2010.5 Citroen C4 PICASSO DAG key
[x] Cancel search: keyPage 89 of 355
IV
84
A C C E S S
Locking the vehicle with
exterior perimeter monitoring
only
Deactivate the interior volumetric
monitoring to avoid unwanted trig-
gering of the alarm in certain cases
such as:
- leaving a pet in the vehicle,
- leaving a window partially open,
- washing your vehicle, To be effective, this deactivation
must be carried out each time the
ignition is switched off.
Deactivation of the interior
volumetric monitoring
Switch off the ignition.
Within ten seconds, press the
button until the indicator lamp is
lit continuously.
Get out of the vehicle.
Press the locking button on the
remote control immediately.
The exterior perimeter monitoring
alone is activated: the indicator lamp
o n t h e b u t t o n fl a s h e s o n c e p e r s e c o n d .
Triggering of the alarm
The monitoring functions remain
active until the alarm has been trig-
gered eleven times in succession.
When the vehicle is unlocked using
t h e r e m o t e c o n t r o l , r a p i d fl a s h i n g
of the indicator lamp on the button
informs you that the alarm was trig-
gered during your absence. When
the ignition is switched on, this
fl a s h i n g s t o p s i m m e d i a t e l y . Failure of the remote control
To deactivate the monitoring func-
tions:
Locking the vehicle without
activating the alarm
Malfunction
Automatic activation *
Lock or deadlock the vehicle us-
ing the key in the driver's door
lock.
W h e n t h e i g n i t i o n i s s w i t c h e d o n , fi x e d
lighting of the indicator lamp on the
button indicates a malfunction of the
system.
Have it checked by a CITROËN dealer.
2 minutes after the last door or the
boot is closed, the system is activat-
ed automatically.
To avoid triggering the alarm on
e n t e r i n g t h e v e h i c l e , fi r s t p r e s s
the unlocking button on the re-
mote control.
Unlock the vehicle using the key
in the driver's door lock.
Open the door; the alarm is trig-
gered.
Switch on the ignition; the alarm
stops. The indicator lamp on the
button switches off.
This is indicated by sounding of the
s i r e n a n d fl a s h i n g o f t h e d i r e c t i o n i n -
dicators for thirty seconds.
Reactivation of the interior
volumetric monitoring
Press the unlocking button on the
remote control to deactivate the
exterior perimeter monitoring.
Press the locking button on the
remote control to activate all the
monitoring functions.
The indicator lamp on the button
a g a i n fl a s h e s o n c e p e r s e c o n d .
* According to country.
Page 91 of 355
IV
86
A C C E S S
Reinitialisation
If a window does not rise automati-
cally, its operation must be reini-
tialised:
pull the control until the window
stops,
release the control and pull it
again until the window closes
fully,
continue to hold the control for
approximately one second after
the window has closed,
press the control to lower the
window automatically to the low
position,
when the window has reached
the low position, press the con-
trol again for approximately one
second.
The safety anti-pinch function
is not operational during these
operations. Deactivation of the rear
electric window and door
controls
For the safety of your children,
press control 5 to deactivate the
rear electric window controls re-
gardless of their position. Always remove the key from the
ignition when leaving the vehicle,
even for a short time.
If an obstacle is encountered during
operation of the electric windows,
you must reverse the movement of
the window. To do this, press the
control concerned.
When the driver operates the con-
trols for the passengers' electric
windows, they must ensure that no
one is preventing correct closing of
the windows.
The driver must ensure that the
passengers use the electric win-
dows correctly.
Be aware of children when operat-
ing the windows.
This warning lamp comes
on temporarily on the instru-
ment panel on deactivation
and each time the ignition is
switched on.
This control also deactivates the
interior controls for the rear doors
(refer to the section "Child safety -
Electric child lock").
Page 92 of 355
IV
87
A C C E S S
DOORS
Opening
From outside When the selective unlocking is
a c t i v a t e d , t h e fi r s t p r e s s o f t h e
remote control unlocking button
permits unlocking of the driver's
door only.
Pull on the front door control to
open the door; this unlocks the
vehicle completely.
Pull on the rear door control to
open the door; this unlocks the
door concerned only.
With the selective unlocking acti-
vated:
- the driver's door control unlocks the driver's door only,
- the other door controls unlock the other doors and the boot.
The interior door controls do not
operate when the vehicle is dead-
locked. Manual central locking
control
System for locking or unlocking the
vehicle - the doors and boot - from
the driving position.
Locking
Press this button to lock the ve-
hicle.
The red indicator lamp on the button
comes on.
If one of the doors is open, the cen-
tral locking does not take place.
If the boot or the rear screen is
open, central locking from the in-
side is active for the doors, to allow
long objects to be carried.
After unlocking the vehicle com-
pletely using the remote control
or the key, pull the door handle. From inside
Page 93 of 355
IV
88
A C C E S S
Unlocking
Press this button again to unlock
the vehicle.
The red indicator lamp on the button
goes off.
If the vehicle is locked or dead-
locked from the outside, the red in-
d i c a t o r l a m p fl a s h e s a n d b u t t o n A
is inactive.
In this case, use the remote
control or the key to unlock the
vehicle.
Automatic central locking
This system automatically locks the
doors, boot and rear screen while
driving.
You can activate or deactivate this
function.
Locking
When the speed exceeds 6 mph
(10 km/h), the doors, the boot and
the rear screen lock automatically. Unlocking
Above 6 mph (10 km/h), press
this button to unlock the doors,
the boot and the rear screen
temporarily.
Ignition on:
Deactivation
Press this button again for more
than two seconds.
A c o n fi r m a t i o n m e s s a g e a p p e a r s i n
the multifunction screen. Emergency control
System which locks or unlocks the
doors mechanically in the event of
a malfunction of the battery or of the
central locking.
Locking the driver's door
Insert the key in the lock, then
turn it to the right.
Unlocking the driver's door
Insert the key in the lock, then
turn it to the left.
Locking the front and rear
passenger doors
Insert the key in the lock, located
on the edge of the door, then turn
it one eighth of a turn .
Unlocking the front and rear
passenger doors
Pull the interior door opening
control.
If one of the doors or the boot or
rear screen is open, the automat-
ic central locking does not take
place. Activation
Press this button for more than
two seconds.
A c o n fi r m a t i o n m e s s a g e a p p e a r s i n
the multifunction screen.
Page 94 of 355
IV
89
A C C E S S
After unlocking the vehicle com-
pletely using the remote control
or the key, with the rear screen
closed, pull on the lever 1 and
raise the tailgate.
Lower the tailgate using one of
the two handholds 3 , located on
the interior trim. -
when the engine is
running , this warning
lamp comes on, accom-
panied by a message on
the multifunction screen
for a few seconds,
- when the vehicle is moving
(speed above 6 mph (10 km/h)),
this warning lamp comes on, ac-
companied by an audible signal
and a message in the multifunc-
tion screen for a few seconds.
If the tailgate is not closed correctly:
REAR SCREEN
This opening gives easy access
to the boot, even if you are parked
close to a wall or another vehicle. Closing
Lower the rear screen guiding
it with the wiper arm until it is
closed.
If the rear screen is not closed cor-
rectly: - when the engine is
running , this warning
lamp comes on, accom-
panied by a message in
the multifunction screen
for a few seconds,
- when the vehicle is moving
(speed above 6 mph (10 km/h)),
this warning lamp comes on, ac-
companied by an audible signal
and a message in the multifunc-
tion screen for a few seconds.
The boot and the rear screen
cannot both be open at the same
time.
When the rear screen is open,
you can access the boot by rais-
ing the rear shelf using its tab
(C4 Picasso).
After unlocking the vehicle com-
pletely using the remote control
or the key, with the boot closed,
press the control 2 and raise the
rear screen using the base 4 of
the wiper arm.
Past the balancing point, allow
the tailgate to lower and close
itself (do not assist it or slow it
down).
Opening
Opening
Closing
Page 97 of 355
IV
91
A C C E S S
FUEL TANK
Capacity of the tank: approxi-
mately 60 litres.
Low fuel level When the low fuel level is
reached, this warning lamp
on the instrument panel
comes on, accompanied by
an audible warning and a message
on the multifunction screen.
W h e n i t fi r s t c o m e s o n , about 7 litres
of fuel remain in the tank.
U n t i l s u f fi c i e n t f u e l h a s b e e n
added, this warning lamp appears
every time the ignition is switched
on, accompanied by an audible
warning and a message. Depending
on version, this audible warning
and message are repeated with
increasing frequency as the fuel
level drops towards " 0 ".
Refuel as soon as possible to avoid
running out. A l a b e l o n t h e i n s i d e o f t h e f u e l fi l l e r
fl a p r e m i n d s y o u o f t h e t y p e o f f u e l
to use, depending on your engine
type.
Additions of fuel must be of at least
5 litres to be registered by the fuel
gauge.
Refuelling
I f y o u a r e fi l l i n g y o u r t a n k t o
the top, do not persist after the
3rd cut-off; this could cause
malfunctions.
With Stop & Start, never refuel with
the system in STOP mode; you
must switch off the ignition with the
key. O p e n i n g t h e fi l l e r c a p m a y r e s u l t i n
an inrush of air. This is entirely nor-
mal and results from the sealing of
the fuel system.
Press control switch A , situated
on the switch panel on the left of
t h e d a s h b o a r d , u n t i l t h e f u e l fl a p
opens.
This control switch remains ac- tive for a few minutes after
switching of the ignition. If nec-
essary, switch the ignition on
again to reactivate it.
Take care to select the pump
that delivers the correct type of
fuel for your vehicle.
Introduce the nozzle so as to push
i n t h e m e t a l n o n - r e t u r n fl a p B.
Make sure that the nozzle is
pushed in as far as possible
before starting to refuel (risk of
blowback).
Maintain this position throughout
the refuelling operation.
P u s h t h e f u e l fl a p t o c l o s e i t .
Page 103 of 355
V
97
V I S I B I L I T Y
OF DIRECTIONAL HEADLAMPS
This system adjusts the height of the
xenon headlamp beams automati-
cally and when stationary, according
to the load in the vehicle, so as to
avoid causing a nuisance to other
road user. If a malfunction occurs,
this warning lamp is
displayed in the instru-
ment panel, accom-
panied by an audible
signal and a message in the multi-
function screen.
The system then places your head-
lamps in the lowest position.
Do not touch the xenon bulbs.
Consult a CITROËN dealer.
MANUAL ADJUSTMENT OF HEADLAMPS
To avoid dazzling other road users,
the height of the halogen bulb head-
lamps must be adjusted according
to the load in the vehicle. To do this,
turn the control, located below the
dashboard to the left of the driver, to
the appropriate position:
0. 1 or 2 people in the front seats.
-. 3 people.
1. 4 to 7 people.
-. Intermediate setting.
2. 4 to 7 people + maximum autho-
rised loads.
-. Intermediate setting.
3. Driver + maximum authorised
loads.
Initial setting is position " 0 ".
EXTERIOR SIDE SPOTLAMPS
These illuminate:
- the zones facing the driver’s and
passenger’s doors,
- the zones forward of the door mirrors and rearward of the front
doors.
Switching on
The side spotlamps come on:
- when you unlock the vehicle or press on the lighting button on
the remote control,
- when you remove the key from the ignition,
- when you open a door,
- when you use the remote control.
Switching off
They are timed to go out automati-
cally.
Page 106 of 355
V
97
V I S I B I L I T Y
OF DIRECTIONAL HEADLAMPS
This system adjusts the height of the
xenon headlamp beams automati-
cally and when stationary, according
to the load in the vehicle, so as to
avoid causing a nuisance to other
road user. If a malfunction occurs,
this warning lamp is
displayed in the instru-
ment panel, accom-
panied by an audible
signal and a message in the multi-
function screen.
The system then places your head-
lamps in the lowest position.
Do not touch the xenon bulbs.
Consult a CITROËN dealer.
MANUAL ADJUSTMENT OF HEADLAMPS
To avoid dazzling other road users,
the height of the halogen bulb head-
lamps must be adjusted according
to the load in the vehicle. To do this,
turn the control, located below the
dashboard to the left of the driver, to
the appropriate position:
0. 1 or 2 people in the front seats.
-. 3 people.
1. 4 to 7 people.
-. Intermediate setting.
2. 4 to 7 people + maximum autho-
rised loads.
-. Intermediate setting.
3. Driver + maximum authorised
loads.
Initial setting is position " 0 ".
EXTERIOR SIDE SPOTLAMPS
These illuminate:
- the zones facing the driver’s and
passenger’s doors,
- the zones forward of the door mirrors and rearward of the front
doors.
Switching on
The side spotlamps come on:
- when you unlock the vehicle or press on the lighting button on
the remote control,
- when you remove the key from the ignition,
- when you open a door,
- when you use the remote control.
Switching off
They are timed to go out automati-
cally.