2010.5 Citroen C4 PICASSO DAG reset
[x] Cancel search: resetPage 8 of 355
11
F A M I L I A R I S A T I O N
8. Controls:
- Trip mileage recorder reset button
- Lighting rheostat
9. W a r n i n g l a m p s d i s p l a y ( w i t h t h e
MyWay or NaviDrive multifunction
s c r e e n )
10. Electric parking brake
11. Instrument panel
12. Hazard warning lamps
13. Switch panels:
- Emergency or assistance
- Lane departure warning system
14. ESP deactivation button
15. Steering lock - Ignition switch
16. Multifunction screen steering
mounted controls
17. Horn
1. Controls:
- Lighting
- Direction indicators
- Front and rear foglamps
2. Paddles for automatic gearbox or
6-speed electronic gearbox system
3. Cruise control and speed limiter
steering mounted controls
4. Direction indicator warning lamps
5. Audio and telematics system
steering mounted controls
6. Selector for automatic gearbox or
6-speed electronic gearbox system
7. Controls:
- Windscreen wipe
- Screenwash
- Rear screen wipe
- Trip computer
I N S T R U M E N T S A N D C O N T R O L S
18. Optional function controls
( o n s t e e r i n g w h e e l )
19. Fusebox access cover
20. Controls:
- F u e l fi l l e r fl a p
- Front and rear parking sensors
- Stop & Start
- Volumetric alarm deactivation
- H e a d l a m p a d j u s t m e n t
21. Bonnet release
22. Mirror controls
Page 26 of 355
I
30M O N I T O R I N G
MONOCHROME INSTRUMENT PANEL (WITH MULTIFUNCTION SCR
EEN A)
1. Rev counter
2. Gear shift indicator for a manual
gearbox or gear selector lever and
gear for the electronic gearbox
system or automatic gearbox
3. "Foot on brake" warning lamp for
the electronic gearbox system or
automatic gearbox/Electric parking
brake
4. Speedometer
5. Cruise control or speed limiter
setting
A. Lighting rheostat (available day
and night)
B. Trip mileage recorder reset
Central screen Controls
TWO-TONE INSTRUMENT PANEL (WITH MULTIFUNCTION SCRE
EN C)
6. Fuel gauge
7. Trip mileage recorder
8. Multifunction screen A/C
9. Total mileage recorder
In this zone, the following infor- mation appears in succession
when the ignition is switched on:
- service indicator,
- engine oil level indicator,
- total mileage recorder.
Page 27 of 355
I
31
M O N I T O R I N G
INSTRUMENT PANEL WITH MYWAY OR NAVIDRIVE MULTIFUNCTION SCREEN
1. Cruise control or speed limiter
setting
2. Speedometer
3. MyWay or NaviDrive multifunc-
tion screen
4. Rev counter
5. "Foot on brake" warning lamp for
the electronic gearbox system or
automatic gearbox/Electric park-
ing brake
6. Fuel gauge
A. Lighting rheostat (available day
and night)
B. Trip mileage recorder reset
Central screen Controls
7. Gear shift indicator for a manual
gearbox or selector lever posi-
tion and gear for the electronic
gearbox system or automatic
gearbox
8. Trip mileage recorder
9. Total mileage recorder
In this zone, the following infor- mation appears in succession
when the ignition is switched on:
- service indicator,
- engine oil level indicator,
- total mileage recorder.
10. Warning lamp zone.
Page 37 of 355
I
41
M O N I T O R I N G
Service indicator
System which informs the driver
when the next service is due, in ac-
cordance with the manufacturer's
servicing schedule.
The point at which the service is due
is calculated from the last indicator
zero reset. It is determined by two
parameters:
- the distance travelled,
- the time elapsed since the last
service. 5 seconds after the ignition is switched
on,
the spanner is switched off ; the
distance recorder resumes its normal
operation. The display then indicates
the total and trip distances.
Less than 620 miles (1 000 km)
remain before the next service is due
Example: 558 miles (900 km) re-
main before the next service is due.
For 5 seconds after the ignition is
switched on, the display indicates: Service overdue
For 5 seconds after the ignition is
switched on,
t h e s p a n n e r fl a s h e s
to indicate that the service must be
carried out as soon as possible.
Example: the service is overdue by
186 miles (300 km).
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition is
switched on, the distance recorder
resumes its normal operation. The
spanner remains on to indicate that
a service must be carried out soon. 5 seconds after the ignition is
switched on, the distance recorder
resumes its normal operation.
The
spanner remains lit .
More than 620 miles (1 000 km)
remain before the next service is
due
For 5 seconds after the ignition is
switched on, the spanner symbol-
ising the service operations comes
on. The distance recorder display
line indicates the distance remaining
before the next service is due.
Example: 2 976 miles (4 800 km)
remain before the next service is
due.
For 5 seconds after the ignition is
switched on, the display indicates:
The distance remaining may be
weighted by the time factor, depend-
ing on the driver's driving habits.
Therefore, the spanner may also
come on if you have exceeded the
two year service interval.
Page 38 of 355
I
42M O N I T O R I N G
Service indicator zero reset
Engine oil level indicator
After each service, the service indi-
cator must be reset to zero.
The procedure for resetting to zero
is as follows:
switch off the ignition,
press and hold the trip distance
recorder zero reset button,
switch on the ignition; the dis-
tance recorder display begins a
countdown,
when the display indicates "=0" ,
release the button; the spanner
disappears. System which informs the driver
whether the engine oil level is cor-
rect or not.
This information is displayed for a
few seconds when the ignition is
switched on, after the service infor-
mation.
The level read will only be correct if
the vehicle is on level ground and
the engine has been off for more
than 15 minutes.
Oil level correct
Oil level low
T h i s i s i n d i c a t e d b y t h e fl a s h i n g o f
"OIL" , accompanied by an audible
signal and a message on the multi-
function screen.
I f t h e l o w o i l l e v e l i s c o n fi r m e d b y a
check using the dipstick, it is essen-
tial that the level is topped up to pre-
vent damage to the engine. Oil level gauge fault
T h i s i s i n d i c a t e d b y t h e fl a s h i n g o f
"OIL--" . Contact a CITROËN dealer.
Dipstick
Refer to the "Checks" section to lo-
c a t e t h e d i p s t i c k a n d t h e o i l fi l l e r c a p
on your engine. There are 2 marks on
the dipstick:
- A = max; never ex-
ceed this level,
- B = min; top up the
l e v e l v i a t h e o i l fi l l e r
cap, using the type
of oil suited to your
engine.
Following this operation, if you wish
to disconnect the battery, lock the
v e h i c l e a n d w a i t a t l e a s t fi v e m i n u t e s
for the zero reset to be taken into ac-
count.
Page 39 of 355
I
42M O N I T O R I N G
Service indicator zero reset
Engine oil level indicator
After each service, the service indi-
cator must be reset to zero.
The procedure for resetting to zero
is as follows:
switch off the ignition,
press and hold the trip distance
recorder zero reset button,
switch on the ignition; the dis-
tance recorder display begins a
countdown,
when the display indicates "=0" ,
release the button; the spanner
disappears. System which informs the driver
whether the engine oil level is cor-
rect or not.
This information is displayed for a
few seconds when the ignition is
switched on, after the service infor-
mation.
The level read will only be correct if
the vehicle is on level ground and
the engine has been off for more
than 15 minutes.
Oil level correct
Oil level low
T h i s i s i n d i c a t e d b y t h e fl a s h i n g o f
"OIL" , accompanied by an audible
signal and a message on the multi-
function screen.
I f t h e l o w o i l l e v e l i s c o n fi r m e d b y a
check using the dipstick, it is essen-
tial that the level is topped up to pre-
vent damage to the engine. Oil level gauge fault
T h i s i s i n d i c a t e d b y t h e fl a s h i n g o f
"OIL--" . Contact a CITROËN dealer.
Dipstick
Refer to the "Checks" section to lo-
c a t e t h e d i p s t i c k a n d t h e o i l fi l l e r c a p
on your engine. There are 2 marks on
the dipstick:
- A = max; never ex-
ceed this level,
- B = min; top up the
l e v e l v i a t h e o i l fi l l e r
cap, using the type
of oil suited to your
engine.
Following this operation, if you wish
to disconnect the battery, lock the
v e h i c l e a n d w a i t a t l e a s t fi v e m i n u t e s
for the zero reset to be taken into ac-
count.
Page 40 of 355
I
43
M O N I T O R I N G
Distance recorders
The total and trip distances are dis-
played for thirty seconds when the
ignition is switched off, when the
driver's door is opened and when
the vehicle is locked or unlocked.
Measures the total distance trav-
e l l e d b y t h e v e h i c l e s i n c e i t s fi r s t
registration.
Trip distance recorder
Lighting rheostat
P e r m i t s m a n u a l a d j u s t m e n t o f t h e
brightness of the instruments and
controls in relation to the exterior
brightness. Only operates when the
vehicle lighting is on, with the excep-
tion of the daytime running lamps.
Activation
Press the button to change the
brightness of the instruments
and controls.
When the lighting reaches the
minimum setting, release the
button, then press again to in-
crease it.
or
When the lighting reaches the
maximum setting, release the
button, then press again to re-
duce it.
When the lighting reaches the
level of brightness required, re-
lease the button.
Deactivation
When the vehicle lighting is off, or
i n d a y m o d e o n v e h i c l e s fi t t e d w i t h
daytime running lamps, pressing the
button does not have any effect.
Total distance recorder
Measures a distance travelled since
it was reset to zero by the driver.
With the ignition on, press and
hold this button until zeros ap-
pear.
Page 49 of 355
II
52
M U L T I F U N C T I O N S C R E E N S
Main Menu
T r a f fi c I n f o r m a t i o n
N a v i g a t i o n / G u i d a n c e
Map
Audio Functions
Telematics
C o n fi g u r a t i o n ,
t o c o n fi g u r e t h e s c r e e n
( d a t e , t i m e . . . ) a n d d e fi n e v e -
hicle parameters
Video
Vehicle Diagnostics
- " A l e r t l o g " ,
- " S t a t u s o f f u n c t i o n s " .
Press button
A t o d i s p l a y t h e " M a i n
M e n u " :
TRIP COMPUTER
System which provides current infor-
mation concerning the trip travelled
( r a n g e , f u e l c o n s u m p t i o n . . . ) .
Monochrome screen A
Information displays
Press the control for more than
two seconds to reset to zero the
distance travelled, the average
fuel consumption and the aver-
age speed.
Zero reset
The trip computer provides the fol-
lowing information:
- range,
- current fuel consumption,
- distance travelled,
- average fuel consumption,
- average speed.
The next press then returns you
to the normal display.
Press the button, located at the
end of the wiper stalk , to display
the various items of trip computer
data in succession.