I
40M O N I T O R I N G
Warning lamp is on Cause Action/Observations
Maximum
coolant
temperature fi x e d r e d .
The temperature of the
cooling system is too high. Stop as soon as it is safe to do so.
Wait until the engine has cooled down
before topping up the level, if necessary.
If the problem persists, contact a
CITROËN dealer.
Battery
charge fi x e d . The battery charging circuit
has a fault (dirty or loose
terminals, slack or cut
alternator belt, ...). The warning lamp should go off when the
engine is started.
If it does not switch off, contact a
CITROËN dealer.
Door(s) open fi x e d i f t h e s p e e d
is below 6 mph (10 km/h).
A door, the boot or the rear
screen is still open. Close the door or boot.
fi x e d a n d
accompanied by
an audible signal if the speed is above 6 mph (10 km/h).
+
Seat belts
not fastened/ unfastened fi x e d . The driver and/or the front/
rear passenger has not
fastened or has unfastened
their seat belt.
Pull the strap then insert the tongue in the buckl
e. The illuminated dots represent the passengers
that have not fastened/unfastened their seat belt.
They come on:
- fi x e d f o r 3 0 a b o u t s e c o n d s o n s t a r t i n g
the vehicle,
- fi x e d f r o m 0 t o 1 2 m p h ( 0 t o 2 0 k m / h ) when driving,
- fl a s h i n g a b o v e 1 2 m p h ( 2 0 k m / h ) , accompanied by an audible signal for
about 120 seconds.
X
176
C H E C K S
CHECKING LEVELS
Check all of these levels regularly
and top them up if necessary, unless
otherwise indicated.
I f a l e v e l d r o p s s i g n i fi c a n t l y , h a v e t h e
corresponding system checked by a
CITROËN dealer.
Oil level
Engine oil change
Refer to the Maintenance and
Warranty Guide for details of the in-
terval for this operation. O i l s p e c i fi c a t i o n
The oil must correspond to your en-
gine and conform to the manufactur-
er's recommendations.
Brake fluid level
C h a n g i n g t h e fl u i d
Refer to the Maintenance and
Warranty Guide for details of the in-
terval for this operation.
F l u i d s p e c i fi c a t i o n
T h e b r a k e fl u i d m u s t c o n f o r m t o t h e
manufacturer's recommendations
a n d f u l fi l t h e D O T 4 s t a n d a r d s .
Coolant level
Changing the coolant
The coolant does not have to be
changed.
F l u i d s p e c i fi c a t i o n
The coolant must conform to the
manufacturer's recommendations.
The reading will only be
correct if the vehicle is on
level ground and the engine
has been off for more than
1 5 m i n u t e s .
The check is carried out either when
the ignition is switched on using the
oil level indicator on the instrument
panel, or using the dipstick. T h e b r a k e fl u i d l e v e l s h o u l d
be close to the "MAX" mark.
If it is not, check the brake
pad wear.
The coolant level should be
close to the "MAX" mark but
should never exceed it.
When the engine is warm,
the temperature of the coolant is
regulated by the fan. This can oper-
ate with the ignition off.
O n v e h i c l e s w h i c h a r e fi t t e d w i t h
a p a r t i c l e e m i s s i o n fi l t e r , t h e f a n
may operate after the vehicle has
b e e n s w i t c h e d o f f , e v e n i f t h e e n -
gine is cold.
In addition, as the cooling system is
pressurised, wait at least one hour
after switching off the engine before
carrying out any work.
To avoid any risk of scalding, un-
screw the cap by two turns to al-
low the pressure to drop. When the
pressure has dropped, remove the
cap and top up the level.
In order to maintain the re-
liability of the engine and
emission control system,
the use of additives in the engine
oil is prohibited. When working under the
bonnet, take care, as cer-
tain areas of the engine
may be extremely hot (risk
of burns).
Power steering fluid level T h e p o w e r s t e e r i n g fl u i d
level should be close to the
"MAX" mark. Unscrew the
cap, with the engine cold, to
check the level.
