2009 YAMAHA MAJESTY 125 brake light

EAUS1133
Replacing a tail/brake light
bulb or a rear turn signal
light bulb
Tail/brake light bulb1. Remove the tail/brake light lens by removing the screw.
1. Screw
2. Tail/brake light lens
3. Bulb
2. Remove the burnt-out bulb bypushing it in and turning it coun-
terclockwise.
3. Insert a new bulb into the socket, push it in, and then turn it clock-
wise until it stops. 4. Install the lens by installing the
screw. NOTICE: Do not over-
tighten the screws, otherwise
the lens may break.
[ECA10681]
Rear turn signal light bulb 1. Remove the left or right tail/brake light lens by removing the screw.
2. Remove the turn signal light lens by pulling it backwards.
3. Remove the turn signal light bulb lens by removing the screw.
1. Turn signal light lens
2. Screw
3. Turn signal light bulb lens
4. Bulb
4. Remove the burnt-out bulb bypushing it in and turning it coun-
terclockwise. 5. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
6. Install the turn signal light bulb lens by installing the screw.
NOTICE: Do not overtighten
the screws, otherwise the lens
may break.
[ECA10681]
7. Install the turn signal light lens.
8. Install the tail/brake light lens by installing the screw. NOTICE: Do
not overtighten the screws,
otherwise the lens may break.
[ECA10681]

1
2
3
4

1
2
3

PERIODIC MAINTENANCE AND ADJUSTMENT
6-29
6
5D8-F8199-E1.QXD 11/7/08 15:49 Página 66

cleaning products, solvent or
thinner, fuel (gasoline), rust
removers or inhibitors, brake
fluid, antifreeze or electrolyte.
●Do not use high-pressure was-
hers or steam-jet cleaners sin-
ce they cause water seepage
and deterioration in the follo-
wing areas: seals (of wheel and
swingarm bearings, fork and
brakes), electric components
(couplers, connectors, instru-
ments, switches and lights),
breather hoses and vents.
●For scooters equipped with a
windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or scrat-
ching. Some cleaning com-
pounds for plastic may leave
scratches on the windshield.
Test the product on a small hid-
den part of the windshield to
make sure that it does not lea-
ve any marks. If the windshield
is scratched, use a quality
plastic polishing compound
after washing.
After normal use
1. Remove dirt with warm water, a
mild detergent, and a soft, clean
sponge, and then rinse tho-
roughly with clean water. Use a
toothbrush or bottlebrush for
hard-to-reach areas. Stubborn
dirt and insects will come off
more easily if the area is covered
with a wet cloth for a few minutes
before cleaning.
After riding in the rain, near the sea or
on salt-sprayed roads
1. Since sea salt or salt sprayed on
the roads during winter are extre-
mely corrosive in combination
with water, carry out the following
steps after each ride in the rain,
near the sea or on salt-sprayed
roads.
TIP
Salt sprayed on roads in the winter
may remain well into spring.
1. Clean the scooter with cold water
and a mild detergent after the
engine has cooled down. NOTI-
CE: Do not use warm watersince it increases the corrosive
action of the salt.
[ECA10791]
2. Apply a corrosion protection
spray on all metal, including
chrome- and nickel-plated, surfa-
ces to prevent corrosion.
After cleaning
1. Dry the scooter with a chamois or
an absorbing cloth.
2. Use a chrome polish to shine
chrome, aluminum and stainless-
steel parts, including the exhaust
system. (Even the thermally indu-
ced discoloring of stainless-steel
exhaust systems can be removed
through polishing.)
3. To prevent corrosion, it is recom-
mended to apply a corrosion pro-
tection spray on all metal, inclu-
ding chrome- and nickel-plated,
surfaces.
4. Use spray oil as a universal clea-
ner to remove any remaining dirt.
5. Touch up minor paint damage
caused by stones, etc.
6. Wax all painted surfaces.
7. Let the scooter dry completely
before storing or covering it.
SCOOTER CARE AND STORAGE
7-2
7
5D8-F8199-E1.QXD 10/7/08 07:39 Página 72

Size:
120 / 70 - 12 51L
Manufacturer/model:
PIRELLI / SL66
Manufacturer/model:
MICHELIN / BOOPER
Manufacturer/model:
CONTINENTAL / ZIPPY 1
Rear tire:Type:
Tubeless
Size:
130 / 70 - 12 56L
Manufacturer/model:
PIRELLI / SL66
Manufacturer/model:
MICHELIN / BOOPER
Manufacturer/model:
CONTINENTAL /ZIPPY 1
Loading:Maximum load:
177 kg (390 lb)
Tire air pressure (measured on cold
tires):
Loading condition:
0–90 kg (0–198 lb)
Front:
190 kPa (1.90 kgf/cm
2, 28 psi, 1.90 bar)
Rear:
220 kPa (2.20 kgf/cm
2, 32 psi, 2.20 bar)
Loading condition:
90 kg - maximum load
Front:
190 kPa (1.90 kgf/cm
2, 28 psi, 1.90 bar)Rear:
240 kPa (2.40 kgf/cm
2, 35 psi, 2.40 bar)
High-speed riding:Front:
190 kPa (1.90 kgf/cm2, 28 psi, 1.90 bar)
Rear:
220 kPa (2.20 kgf/cm
2, 32 psi, 2.20 bar)
Front wheel:Wheel type:
Cast wheel
Rim size:
12 x MT3.5
Rear wheel:Wheel type:
Cast wheel
Rim size:
12 x MT3.75
Front brake:Type:
Single disc brake
Operation:
Right hand operation
Recommended fluid:
DOT 4
Rear brake:Type:
Single disc brake
Operation:
Left hand operation
Recommended fluid:
DOT 4
Front suspension:Type:
Telescopic forkSpring/shock absorber type:
Coil spring/oil damper
Wheel travel:
90.0 mm (3.54 in)
Rear suspension:Type:
Unit swing
Spring/shock absorber type:
Coil spring/oil damper
Wheel travel:
90.0 mm (3.54 in)
Electrical system:Ignition system:
DC. CDI
Charging system:
AC magneto
Battery:Model:
CB7L-B2
Voltage, capacity:
12 V, 8.0 Ah
Headlight:Bulb type:
Halogen bulb
Bulb voltage, wattage x quantity:Headlight:
12 V, 55.0 W x 2
Tail/brake light:
12 V, 21.0 W/5.0 W x 2
Front turn signal light:
12 V, 21.0 W x 2
Rear turn signal light:
12 V, 10.0 W x 2
SPECIFICATIONS
8-2
8
5D8-F8199-E1.QXD 10/7/08 07:39 Página 76

AAcceleration and deceleration ...................5-2
Air filter and V-belt case air filter
elements ................................................6-14
Anti-theft alarm (optional) ..........................3-5
Auxiliary light bulb, replacing ...................6-30
BBattery......................................................6-24
Brake fluid level, checking .......................6-20
Brake fluid, changing ...............................6-21
Brake lever, front ........................................3-7
Brake lever, rear .........................................3-7
Brake levers, lubricating ..........................6-21
Braking .......................................................5-3
CCables, checking and lubricating ............6-21
Carburetor,adjusting.................................6-15
Care............................................................7-1
Catalytic converter ...................................3-10
Centerstand and sidestand, checking
and lubricating .......................................6-22
Clock ..........................................................3-5
Coolant.....................................................6-12
Coolant temperature warning light ............3-2
DDimmer switch ...........................................3-6
EEngine break-in ..........................................5-4
Engine oil ...................................................6-9
FFinal transmission oil ...............................6-11
Front and rear brake lever free play.........6-18
Front and rear brake pads, checking ......6-19
Front fork, checking .................................6-23Fuel ............................................................3-8
Fuel and battery voltage gauge .................3-4
Fuel consumption, tips for reducing ..........5-3
Fuel tank breather/overflow hose ..............3-9
Fuel tank cap .............................................3-7
Fuses, replacing .......................................6-26
HHandlebar switches ...................................3-6
Hazard switch ............................................3-6
Headlight bulb, replacing .........................6-26
High beam indicator light...........................3-2
Horn switch ................................................3-6
IIdentification numbers ...............................9-1
Ignition circuit cut-off system ..................3-14
Indicator and warning lights ......................3-2
KKey identification number ..........................9-1
LLicense plate light bulb, replacing ...........6-30
MMain switch/steering lock ..........................3-1
Matte color, caution ...................................7-1
Model label ................................................9-2
OOil change indicator ...................................3-2
PPanels, removing and installing .................6-7
Parking .......................................................5-4
Part locations .............................................2-1
Periodic maintenance and lubrication
chart .........................................................6-3
Pre-operation check list .............................4-2
SSafe-riding points.......................................1-5
Safety information ......................................1-1
Seat ..........................................................3-10
Shock absorber assemblies, adjusting....3-13
Sidestand .................................................3-13
Spark plug, checking .................................6-8
Specifications.............................................8-1
Speedometer unit ......................................3-3
Start switch ................................................3-6
Starting off .................................................5-2
Starting the engine.....................................5-1
Steering, checking ...................................6-23
Storage.......................................................7-3
Storage compartment ..............................3-11
Storage compartment ..............................3-12
TTail/brake light bulb or rear turn signal light
bulb, replacing .......................................6-29
Throttle cable free play, adjusting ............6-15
Tires .........................................................6-16
Tool kit ........................................................6-1
Troubleshooting .......................................6-31
Troubleshooting charts ............................6-32
Turn signal indicator lights .........................3-2
Turn signal light bulb (front), replacing ....6-28
Turn signal switch ......................................3-6
VValve clearance ........................................6-16
Vehicle identification number .....................9-1
WWheel bearings, checking........................6-24
Wheels .....................................................6-18
INDEX
5D8-F8199-E1.QXD 10/7/08 07:39 Página 80