2009 SUBARU TRIBECA Trim

AB-19
Curtain Airbag Module
AIRBAG SYSTEM
7. Curtain Airbag Module
A: REMOVAL
CAUTION:
Refer to “CAUTION” of “General Description”
before handling the airbag module. 4, CAUTION, General Description.>
1) Turn the ignition switch to OFF.
2) Disconnect the ground cable from battery and
wait for at least 20 seconds before starting work.
3) Remove the front pillar upper trim and center pil-
lar upper trim. PER TRIM, REMOVAL, Side Trim.> CENTER PILLAR UPPER TRIM, REMOVAL, Side
Trim.>
4) Remove the rear quarter trim. REMOVAL, Rear Quarter Trim.>
5) Remove the roof trim. AL, Roof Trim.>
6) Disconnect the curtain airbag module connector.
7) Remove the bolts, and then remove the curtain
airbag module.
CAUTION:
•Be careful not to damage the curtain airbag
module during removal.
•Never open the curtain airbag module before
deploying it. Never reuse the deployed curtain
airbag module.
8) Remove the front piller from front pillar pad.
B: INSTALLATION
CAUTION:
•Refer to “CAUTION” of “General Description”
before handling the airbag module. 4, CAUTION, General Description.>
•When installing the curtain airbag module, in-
stall a specified part at specified place.
•Be careful not to damage the curtain airbag
module during removal.
•Never open the curtain airbag module before
deploying it. Never reuse the deployed curtain
airbag module.
•Make sure that there are no foreign matter on
airbag module.
Install in the reverse order of removal.
Tightening torque:
7.5 N·m (0.77 kgf-m, 5.5 ft-lb)
AB-01277
AB-01278
AB-01279

AB-20
Curtain Airbag Module
AIRBAG SYSTEM
C: INSPECTION
CAUTION:
Refer to “CAUTION” of “General Description”
before handling the airbag module. 4, CAUTION, General Description.>
Check for the following, and replace the damaged
parts with new parts. AIRBAG MODULE, INSPECTION, Inspection Lo-
cations After a Collision.>
1) With side collision (when curtain airbag is de-
ployed)
•Curtain airbag module assembly
•Roof Trim
•Front pillar upper trim
•Front piller pad (blue)
•Center pillar upper trim
•Center piller pad (green)
•Rear quarter upper trim
•Rear quarter piller pad (red)
•Airbag guide
2) When damage is found by visual check
•Assist grip
•Assist grip bracket
•Curtain airbag harness and connector on body
side.
3) With side collision (when curtain airbag is not de-
ployed)
Check the roof trim, pillar trim and airbag module
visually, and then replace them with new ones if
damaged or cracked.
Specially inspect the damage of airbag module
body, mounting bracket and harness connector.
4) Without side collision (dirt and damage of cover)
Replace the corresponding part with a new one.

AB-22
Side Airbag Sensor
AIRBAG SYSTEM
9. Side Airbag Sensor
A: REMOVAL
1) Turn the ignition switch to OFF.
2) Disconnect the ground cable from battery and
wait for at least 20 seconds before starting work.
3) Remove the center pillar lower trim. 44, CENTER PILLAR LOWER TRIM, REMOVAL,
Side Trim.>
4) Remove the seat belt retractor of the front outer
seat belt. SEMBLY, REMOVAL, Front Seat Belt.>
5) Remove the nut and disconnect the airbag con-
nector to remove side airbag sensor.
B: INSTALLATION
CAUTION:
•Do not reuse the bolt and nut.
•Always use new bolts and nuts for them.
Install in the reverse order of removal.
Tightening torque:
8 N·m (0.82 kgf-m, 5.9 ft-lb)
C: INSPECTION
Check for the following, and replace the damaged
parts with new parts.
•Mounting bracket or connector of side airbag
sensor is damaged.
•Side airbag is deployed.
AB-00634

AB-23
Curtain Airbag Sensor
AIRBAG SYSTEM
10.Curtain Airbag Sensor
A: REMOVAL
1) Turn the ignition switch to OFF.
2) Disconnect the ground cable from battery and
wait for at least 20 seconds before starting work.
3) Remove the rear quarter lower trim. 45, REMOVAL, Rear Quarter Trim.>
4) Remove the nut and disconnect the airbag con-
nector to remove the curtain airbag sensor.
B: INSTALLATION
CAUTION:
•Do not reuse the bolt and nut.
•Always use new bolts and nuts for them.
Install in the reverse order of removal.
Tightening torque:
8 N·m (0.82 kgf-m, 5.9 ft-lb)
C: INSPECTION
Check for the following, and replace the damaged
parts with new parts.
•Mounting bracket or connector of curtain airbag
sensor is damaged.
•Curtain airbag is deployed.
AB-00727

ET-15
Front Speaker
ENTERTAINMENT
10.Front Speaker
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the front door trim. MOVAL, Door Trim.>
3) Remove the front speaker mounting screws.
4) Disconnect the harness connector and remove
the front speaker.
B: INSTALLATION
Install in the reverse order of removal.
ET-00175

ET-17
Rear Speaker
ENTERTAINMENT
12.Rear Speaker
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the rear door trim. MOVAL, Door Trim.>
3) Remove the rear speaker mounting screws.
4) Disconnect the harness connector and remove
the rear speaker.
B: INSTALLATION
Install in the reverse order of removal.
ET-00178

ET-18
Woofer
ENTERTAINMENT
13.Woofer
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the quarter trim. MOVAL, Rear Quarter Trim.>
3) Remove the woofer bracket mounting screws.
4) Disconnect the harness connector and detach
the woofers.
B: INSTALLATION
Install in the reverse order of removal.
ET-00179

ET-20
Antenna Amplifier
ENTERTAINMENT
15.Antenna Amplifier
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the rear gate trim. MOVAL, Rear Gate Trim.>
3) Disconnect the harness connectors and termi-
nals.
4) Remove the screws and detach the antenna am-
plifier.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
Measure the resistance of antenna amplifier.
Te r m i n a l N o . S t a n d a r d
(1) and amplifier body 10 kΩ or more
(2)-b and Amplifier body 10 kΩ or more
(3)-a and Amplifier body 10 kΩ or more
ET-00180
ET-00181
(2),(3)
(1)
(3)-a
(2)-b