2009 SUBARU TRIBECA Trim

EI-50
Roof Trim
EXTERIOR/INTERIOR TRIM
23.Roof Trim
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the spot map light. MOVAL, Spot Map Light.>
3) Remove the room light or rear entertainment
(model with rear entertainment system). LI-30, REMOVAL, Room Light.>
4) Remove the sun visor. AL, Sun Visor.>
5) Remove the assist grip. AL, Assist Grip.>
6) Remove the front pillar upper trim and center pil-
lar upper trim. Trim.>
7) Remove the rear quarter upper trim. 45, REMOVAL, Rear Quarter Trim.>
8) Remove the sunroof opening trim.
9) Remove the clips and each harness, pull out the
rear center seat belt, and remove the roof trim.
B: INSTALLATION
Install in the reverse order of removal.
EI-00501
EI-01354

EI-51
Rear Gate Trim
EXTERIOR/INTERIOR TRIM
24.Rear Gate Trim
A: REMOVAL
1) Remove the claws (A), and remove the rear gate
pillar trim.
2) Remove the clips and claws (A), and remove the
rear gate upper trim.
3) Remove the cover in the inner handle, and loos-
en the inside screw.
4) Turn over the weather strip, and remove the
clips.
5) Remove the clips (A), and remove the rear gate
lower trim.
B: INSTALLATION
Install in the reverse order of removal.EI-00670:(A)
EI-01358
(A)(A)(A)
EI-01359
EI-01360
(A)(A)

EI-52
Rear Gate Garnish
EXTERIOR/INTERIOR TRIM
25.Rear Gate Garnish
A: REMOVAL
1) Remove the hexagon cap nut (A).
2) Remove the rear gate garnish.
B: INSTALLATION
Use new double-sided tapes, and install in the re-
verse order of removal.
NOTE:
Refer to the installing procedure of side garnish.
Tightening torque:
4.5 N·m (0.46 kgf-m, 3.32ft-lb)
(A) Hexagon cap nut
(B) Double-sided tape
EI-01355
(A)
EI-01356
(B)
(A)

EI-53
Heat Shield Cover
EXTERIOR/INTERIOR TRIM
26.Heat Shield Cover
A: REMOVAL
1. FRONT HEAT SHIELD COVER
1) Remove the rear exhaust pipe and muffler.
2) Remove the bolts to remove the front heat shield
cover.
2. CENTER HEAT SHIELD COVER
1) Remove the fuel tank protector. REMOVAL, Fuel Tank Protector.>
2) Remove the nut and bolt to remove center heat
shield cover.
3. REAR HEAT SHIELD COVER
1) Remove the muffler. MOVAL, Rear Exhaust Pipe.>
2) Remove the rear heat shield cover.
B: INSTALLATION
Install in the reverse order of removal.
AT-03273
AT-03274
EI-01357
EI-00680

EI-54
Trailer Hitch
EXTERIOR/INTERIOR TRIM
27.Trailer Hitch
A: REMOVAL
1) Remove the spare tire hoist. REMOVAL, Spare Tire Hoist.>
2) Remove the bolt, and then detach the main
frame.
CAUTION:
The trailer hitch main frame is heavy. Be careful
when removing.
3) Remove the bolts, and then remove the center
frame.
4) Remove the side frame from the vehicle.
B: INSTALLATION
Install in the reverse order of removal.
Tightening torque:
Refer to “COMPONENT” of “General Descrip-
tion”.
NENT, General Description.>
EI-01383
EI-01384

GW-9
Front Door Glass
GLASS/WINDOWS/MIRRORS
4. Front Door Glass
A: REMOVAL
1) Remove the front door trim. MOVAL, Door Trim.>
2) Remove the sealing cover. MOVAL, Front Sealing Cover.>
3) Operate the power window switch to move the
glass to the position shown in the figure, and then
remove the two bolts through service holes.
4) Tilt the door glass forward, then remove the door
glass from the glass run rubber.
5) Remove the door glass.
CAUTION:
•Since the gear may be disengaged, do not
turn regulator in the closing direction after re-
moving glass.
•Avoid impact and damage to the glass.
6) Remove the bolt (A), and then remove the door
sash (B).
B: INSTALLATION
Install in the reverse order of removal.
CAUTION:
Make sure that the glass stay is placed securely
in sash.
Tightening torque:
Refer to “COMPONENT” of “General Descrip-
tion”. COMPONENT, General Description.>
GW-00479
GW-00480

GW-13
Outer Mirror Assembly
GLASS/WINDOWS/MIRRORS
8. Outer Mirror Assembly
A: REMOVAL
1) Remove the mirror gusset cover.
2) Remove the door trim. AL, Door Trim.>
3) Disconnect the mirror connector.
4) Remove the screws to remove outer mirror as-
sembly.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
Check that the rearview mirror moves properly
when the battery voltage is applied to terminals.
Replace the outer mirror assembly if defective.
(1) Clip
(2) Hook
GW-00484
(2)
(1)
GW-00483
Mirror movement Terminal No.
OFF —
UP 5 (+) and 6 (–)
DOWN 6 (+) or 5 (–)
LEFT 8 (+) and 7 (–)
RIGHT 7 (+) or 8 (–)

GW-16
Rear Door Glass
GLASS/WINDOWS/MIRRORS
11.Rear Door Glass
A: REMOVAL
1) Remove the rear door trim. MOVAL, Door Trim.>
2) Remove the sealing cover. MOVAL, Rear Sealing Cover.>
3) Apply the protective tape (1) to the areas as
shown in the figure.
4) Operate the power window switch to move the
glass to the position shown in the figure, and then
remove the two bolts through service holes.
5) Remove the sash retaining bolts (A), and loosen
the retaining nuts (B).
6) Move the sash (C) upward, and move the nut (B)
to the position on rear door as shown in the figure.
7) Detach the rear part of door glass from sash (1),
and move it backward (2). Tilt the door glass in-
ward, and move it upward to remove (3).
CAUTION:
•Since the gear may be disengaged, do not
turn regulator in the closing direction after re-
moving glass.
•Avoid impact and damage to the glass.
8) Remove the glass run rubber.
9) Remove the door sash.
B: INSTALLATION
Install in the reverse order of removal.
CAUTION:
Make sure that the glass run rubber is placed
securely in door frame and sash.
Tightening torque:
Refer to “COMPONENT” of “General Descrip-
tion”. COMPONENT, General Description.>
GW-00487
(1)
GW-00488
GW-00491
(B)
(A)
GW-00489
(C)
(B)
GW-00490
(1)
(2)
(3)