2009 SUBARU TRIBECA lock

LAN(diag)-77
General Diagnostic Table
LAN SYSTEM (DIAGNOSTICS)
2. BODY INTEGRATED UNIT
Item OperationSpecificationsNoteYES NO
Illumination VR
power supply
Operate the illumination volume,
illumination light is controlled
according to the change of voltage
on data display.
Illumination light is
controlled with
changing of data.
Inspect the illumi-
nation volume.—
Fuel level resis-
tance
Check the fuel level resistance and
fuel level resistance 2. Both resis-
tances are same.
Same valuesInspect the body
integrated unit.
Compare the input and
output values of body inte-
grated unit.
R wiper SW inputWhen rear wiper SW to ON, data
display turns to ON.Tu r n s t o O N .Inspect the rear
wiper switch.—
R wiper outputWhen rear wiper switch to ON, out-
put signal turns to ON.Tu r n s t o O N .Replace the body
integrated unit.
If not operate with output
turned to ON, check the
rear wiper motor.
Keyless Entr yKeyless entr y LOCK/UNLOCK the
doors.OperateInspect the key-
less antenna.
If the antenna is OK,
replace the body inte-
grated unit.
Brake SWWhen brake pedal is depressed, it
turns to ON.Tu r n s t o O N .Inspect the brake
switch.—
Shift Lock SolenoidThe shift lock releases when
depressing the brake pedal.ReleasedInspect the shift
lock.—
Body integrated
unit registration
function setting
Does Vehicle equipment corre-
spond to setting values?Correspondence
Reconfigure the
values according to
vehicle equipment.
—
CustomizeWhen changing customize setting,
the registration completes correctly.RegisteredInspect the body
integrated unit.
Return to original state
after making changes.
Manual mode
Switch the shift (UP/DOWN) on
Manual mode. Indicator is changed
in 1 — 2.
ChangeInspect the shift
lever.—
Function checkEach checking item operate cor-
rectly. (Except for not equipped)OperateInspect for non-
functional actuator.
Module is normal if output
switches to ON.
Security
After locking with keyless entry sys-
tem and open the door, the security
system operates and the horn
sounds.
Horn sounds.
(Security system
operates.)
Inspect the secu-
rity system.
Horn does not activate if
siren is set to ON by cus-
tomizing.

OD(diag)-15
Airbag Connector
OCCUPANT DETECTION SYSTEM (DIAGNOSTICS)
5. Airbag Connector
A: PROCEDURE
1. BUCKLE SWITCH
1) How to disconnect:
(1) Move the slide lock (A) in the direction of ar-
row.
(2) While holding the slide lock (A) in moved po-
sition, disconnect the connector.
CAUTION:
When pulling the slide lock or disconnecting
connector, be sure to hold the connector, not
the harness.
2) How to connect:
Holding the connector (A), and push it in carefully
until a clicking sound is heard.
CAUTION:
Be sure to insert the connector in until it is
locked. Then pull it gently to make sure that it is
locked.
AB-00721
(A)
AB-00016

SE-2
General Description
SEATS
1. General Description
A: COMPONENT
1. FRONT SEAT (DRIVER’S SEAT)
(1) Backrest cover (11) Rear leg cover inside (21) Power seat switch unit
(2) Backrest pad (12) Seat cushion cover (22) Seat heater unit
(3) Backrest frame ASSY (13) Seat cushion pad (23) Lumber support lever
(4) Headrest ASSY (14) Seat cushion frame ASSY (24) Slide rail cover
(5) Headrest lock bushing (15) Rear leg cover outside
(6) Side airbag module (16) Power seat switch knobTightening torque: N·m (kgf-m, ft-lb)
(7) Cover frame (17) Seat side cover outsideT1: 6 (0.61, 4.43)
(8) Backrest back cover (18) Hinge inner cover LHT2: 17.6 (1.79, 12.7)
(9) Seat side cover inside (19) Inner seat belt ASSYT3: 52 (5.30, 37.6)
(10) Hinge inner cover RH (20) Slide rail ASSYT4: 53 (5.40, 38.3)
(1)
(2)
(23)
(22)
(3)
(8)
(4)
(5)
(6)(9)
(10)(11)
(12)
(13)
(14)
(15)
(17)
(21)(19)
(18)
T4
T4
T2
T3
T1
T2
T3
(7)
(24)
(24)
T4
(16)
(20)
SE-00580

SE-3
General Description
SEATS
2. FRONT SEAT (DRIVER’S SEAT)
(1) Backrest cover (10) Hinge inner cover LH (19) Power seat switch unit
(2) Backrest pad (11) Rear leg cover inside (20) Inner seat belt ASSY
(3) Backrest frame ASSY (12) Seat cushion cover (21) Slide rail cover
(4) Headrest ASSY (13) Seat heater unit
(5) Headrest lock bushing (14) Seat cushion pad & frame ASSYTightening torque: N·m (kgf-m, ft-lb)
(6) Side airbag module (15) Rear leg cover outsideT1: 6 (0.61, 4.43)
(7) Cover frame (16) Hinge inner cover RHT2: 17.6 (1.79, 12.7)
(8) Backrest back cover (17) Seat side cover outsideT3: 52 (5.30, 37.6)
(9) Seat side cover inside (18) Power seat switch knobT4: 53 (5.40, 38.3)
T3
T3
(1)
(2)
(3)
(8)
(4)
(5)
(6)
(9)
(10)
(12)
T4
T2
T2
T1
T4
(7)
(11)
(15)
(14)
(21)
(20)
(16)
(13)
(19)
(18)
(17)
SE-00581

SE-4
General Description
SEATS
3. SECOND-ROW SEATS
(1) Headrest (8) Backrest back cover (14) Armrest
(2) Lock bushing (9) Holder (15) Slide rail cover
(3) Backrest cover (10) Seat back latch cover
(4) Backrest pad (11) Hinge outer coverTightening torque: N·m (kgf-m, ft-lb)
(5) Seat cushion cover (12) Hinge inner coverT1: 40 (4.08, 28.9)
(6) Seat cushion pad (13) Cup holderT2: 52 (5.30, 37.6)
(7) Slide rail ASSY
(1)
(1)
(8)
(8)
(3)
(3)
(5)
(6)
(4)
(4)
(11)
(11)
(11)(10)
(12)
(12)
(15)
(15)(7)
(15)
(2)
(2)
(9)
T2
T2
T1
T2
T2
T2
T1
(8)
(9)
(2)
(12)
(14)
(13)
(7)
(12)
(12)
(11)
(11)
SE-00582

SE-5
General Description
SEATS
4. THIRD-ROW SEATS
(1) Headrest (7) Backrest padTightening torque: N·m (kgf-m, ft-lb)
(2) Headrest lock bushing (8) Seat cushion coverT1: 10 (1.01, 7.23)
(3) Hinge lever ASSY (9) Seat cushion padT2: 52 (5.30, 37.6)
(4) Backrest back cover (10) Hinge plateT3: 53 (5.40 38.3)
(5) Backrest frame (11) Inner hinge ASSY
(6) Backrest cover
(1)
(2)
(2)(3)
(3)
(6)
(7)
(8)
(9)
(4)
(5)
(10)
(11)
T3
T3
T3
T1
T3
T1
T2
SE-00583

SE-8
Front Seat
SEATS
4) Remove the screw (A) and clips (B), and then
disconnect the seat switch connector to remove
seat side cover outside.
5) Remove the TORX® bolt, and then remove the
inner seat belt assembly.
6) Remove the screw (A) and clip (B), and then re-
move the seat side cover inside.
7) Remove the two bolts from the reclining hinge on
each left and right side.
8) Remove the clips and hooks, and then detach
the backrest back cover.
9) Remove the lock clip, and then remove the lum-
ber support lever.
(B)
(B)(A)
SE-00584
SE-00585
SE-00412
(A)(B)
SE-00413
SE-00586
SE-00414

SE-9
Front Seat
SEATS
10) Remove the hooks and hog rings at the rear
side of backrest.
11) Remove the headrest lock bushing.
NOTE:
Push outside to remove it from the inside of seat.
12) Remove the hog rings.
13) Remove the cover frame (A).
14) Pull out the backrest frame assembly.
15) Remove the side airbag module.
16) Remove the two bolts on each left and right
side, and then remove the reclining motor assem-
bly.
17) Remove the hog rings (A) on the surface side
of backrest, and then remove the backrest cover
from backrest.
18) Remove the bolt (A) and hook (B) on left and
right side, and then remove the seat cushion frame
from seat rail assembly.
SE-00587
SE-00243
SE-00588
(A)
SE-00337
SE-00589
SE-00388
SE-00590: (A)
SE-00416(B)(A)