2009 SUBARU TRIBECA timing chain assembly

ME(H6DO)-57
Cylinder Head
MECHANICAL
20.Cylinder Head
A: REMOVAL
1) Remove the crank pulley. 41, REMOVAL, Crank Pulley.>
2) Remove the front chain cover. ME(H6DO)-42, REMOVAL, Front Chain Cover.>
3) Remove the timing chain assembly.
Assembly.>
4) Remove the cam sprocket. 49, REMOVAL, Cam Sprocket.>
5) Remove the crank sprocket.
et.>
6) Remove the rear chain cover.
Cover.>
7) Remove the camshaft. REMOVAL, Camshaft.>
8) Remove the cylinder head bolts in the numerical
order as shown in the figure.
Leave bolts (2) and (4) engaged by three or four
threads to prevent the cylinder head from falling.
9) While tapping the cylinder head with a plastic
hammer, separate it from cylinder block.
10) Remove the bolts (2) and (4) to remove cylin-
der head.
11) Remove the cylinder head gasket.
CAUTION:
Be careful not to scratch the mating surface of
cylinder head and cylinder block.
12) Similarly, remove the cylinder head (RH).
B: INSTALLATION
1) Install the cylinder head and gaskets on cylinder
block.
CAUTION:
•Use new cylinder head gaskets.
•Be careful not to scratch the mating surface
of cylinder head and cylinder block.
2) Tighten the cylinder head bolts.
(1) Apply a coat of engine oil to washers and
cylinder head bolt threads.
(2) Install the cylinder head to cylinder block,
and then tighten the bolts with torque of 20 N·m
(2.0 kgf-m, 14 ft-lb) in numerical sequence as
shown in the figure.
(3) Tighten the bolts with torque of 50 N·m (5.1
kgf-m, 37 ft-lb) in numerical sequence as shown
in the figure.
(4) Back off all the bolts by 180° in reverse order
of installation, and back them off again by 180°.
(5) Tighten the bolts with torque of 20 N·m (2.0
kgf-m, 14 ft-lb) in numerical sequence as shown
in the figure.
(6) Tighten the bolts (1) — (4) with torque of 48
N·m (4.9 kgf-m, 35.4 ft-lb) in numerical se-
quence.
(7) Tighten the bolts (5) — (8) with torque of 44
N·m (4.5 kgf-m, 33 ft-lb) in numerical sequence.
(8) Tighten all bolts 90° in the numerical order
as shown in the figure.
(9) Tighten the bolt (1) — (4) by 45° in the nu-
merical order.
3) Install the camshaft. STALLATION, Camshaft.>
4) Install the rear chain cover. 51, INSTALLATION, Rear Chain Cover.>
5) Install the crank sprocket.
Sprocket.>
6) Install the cam sprocket.
Sprocket.>
7) Install the timing chain assembly.
Chain Assembly.>
(2)
(8) (6)
(5) (7)
(4)
(1)(3)
ME-02063
(2)
(8) (6)
(5) (7)
(4)
(1)(3)
ME-02063
(7)
(1) (3)
(4) (2)
(5)
(8)(6)
ME-02064

ME(H6DO)-62
Cylinder Block
MECHANICAL
21.Cylinder Block
A: REMOVAL
NOTE:
Before conducting this procedure, drain the engine
oil completely.
1) Remove the crank pulley. 41, REMOVAL, Crank Pulley.>
2) Remove the front chain cover. ME(H6DO)-42, REMOVAL, Front Chain Cover.>
3) Remove the timing chain assembly.
Assembly.>
4) Remove the cam sprocket.
et.>
5) Remove the crank sprocket.
et.>
6) Remove the rear chain cover.
Cover.>
7) Remove the camshaft. REMOVAL, Camshaft.>
8) Remove the cylinder head. 57, REMOVAL, Cylinder Head.>
9) Remove the drive plate.
Using the ST, lock the crankshaft.
ST 498497100 CRANKSHAFT STOPPER
10) Remove the crankshaft position sensor plate.
11) Remove the crankshaft position sensor brack-
et.
12) Rotate the engine to set oil pan upper.
13) Remove the bolts which secure oil pan lower to
oil pan upper.
14) Insert an oil pan cutter blade between cylinder
block-to-oil pan clearance and remove the oil pan.
CAUTION:
Do not use a screwdriver or similar tools in
place of oil pan cutter.
15) Remove the oil strainer.
ME-02664
ST
ME-00558
ME-00559
ME-00560
LU-02108

ME(H6DO)-68
Cylinder Block
MECHANICAL
26) Install the crankshaft sensor plate.
27) Install the drive plate.
To lock the crankshaft, use ST.
ST 498497100 CRANKSHAFT STOPPER
Tightening torque:
81 N·m (8.3 kgf-m, 60 ft-lb)
28) Install the cylinder head. 57, INSTALLATION, Cylinder Head.>
29) Install the camshaft. INSTALLATION, Camshaft.>
30) Install the rear chain cover. ME(H6DO)-51, INSTALLATION, Rear Chain Cov-
er.>
31) Install the crank sprocket.
Sprocket.>
32) Install the cam sprocket. 49, INSTALLATION, Cam Sprocket.>
33) Install the timing chain assembly.
Chain Assembly.>
34) Install the front chain cover.
Chain Cover.>
35) Install the crank pulley.
Pulley.>
ME-00558
ME-02664
ST