2009 SUBARU TRIBECA recommended oil

5AT-28
Differential Gear Oil
AUTOMATIC TRANSMISSION
3. Differential Gear Oil
A: INSPECTION
1) Park the vehicle on a level surface.
2) Remove the collector cover.
3) Remove the oil level gauge and wipe it clean.
4) Reinsert the level gauge all the way. Make sure
the level gauge is inserted correctly and in the
proper orientation.
5) Remove the oil level gauge again, and check the
level of differential gear oil. If the differential gear oil
level is below “L” line, add oil to bring the level up to
“F” line.
NOTE:
To prevent overfilling the differential gear oil, do not
add oil above the “F” line.
B: REPLACEMENT
1) Lift-up the vehicle.
2) Remove the differential gear oil drain plug using
TORX® BIT T70, and then drain differential gear
oil.
CAUTION:
•Immediately after the vehicle has been run-
ning or after idling for a long time, the differen-
tial gear oil will be hot. Be careful not to burn
yourself.
•Be careful not to spill differential gear oil on
the exhaust pipe to prevent it from emitting
smoke or causing a fire. If differential gear oil is
spilled on the exhaust pipe, wipe it off com-
pletely.
3) Tighten the differential gear oil drain plug using
TORX® BIT T70.
NOTE:
Use a new gasket.
Tightening torque:
70 N·m (7.1 kgf-m, 51.6 ft-lb)
4) Lower the vehicle.
5) Pour gear oil into the gauge hole.
Recommended gear oil:
SPECIFICATION, General Description.>
Gear oil capacity:
1.3 — 1.5 2 ( 1 . 4 — 1 . 6 U S q t , 1 . 1 — 1 . 3 I m p q t )
6) Check the level of differential gear oil.
Oil.>
(A) Upper level
(B) Lower level
AT-00017
(A)
(B)LF
(A) Oil pan
(B) Differential gear oil drain plug
(B)
AT-03127
(A)

5AT-44
Extension Case Oil Seal
AUTOMATIC TRANSMISSION
15) Pour ATF from the oil charge pipe.
Specified fluid:
SUBARU ATF (Part No. K0140Y0700)
Recommended fluid:
IDEMITSU ATF HP
CASTROL TRANSMAX J
PENNZOIL QUAKERSTATE • PENNZOIL ATF-
J
NOTE:
Use of the recommended fluid is permitted only in
regions where the specified fluid is not available.
Capacity:
Fill with the same amount of ATF as drained.
16) Check the level and leaks of the ATF. 5AT-26, Automatic Transmission Fluid.>

5AT-45
Differential Side Retainer Oil Seal
AUTOMATIC TRANSMISSION
12.Differential Side Retainer Oil
Seal
A: INSPECTION
Check for leakage of gear oil from differential side
retainer oil seal part. If there is an oil leak, replace
the oil seal.
B: REPLACEMENT
1) Lift-up the vehicle.
2) Remove the front exhaust pipe. EX(H6DO)-4, REMOVAL, Front Exhaust Pipe.>
3) Remove the differential gear oil drain plug using
TORX® BIT T70, and then drain differential gear
oil.
CAUTION:
•Immediately after the vehicle has been run-
ning or after idling for a long time, the differen-
tial gear oil will be hot. Be careful not to burn
yourself.
•Be careful not to spill the differential gear oil
on exhaust pipe to prevent it from emitting
smoke or fire. If differential gear oil is spilled on
the exhaust pipe, wipe it off completely.
4) Tighten the differential gear oil drain plug.
NOTE:
Use a new gasket.
Tightening torque:
70 N·m (7.1 kgf-m, 51.6 ft-lb)
5) Separate the front drive shaft from the transmis-
sion. Shaft.>
6) Remove the differential side retainer oil seal us-
ing driver wrapped with vinyl tape etc.
7) Using the ST, install the differential side retainer
oil seal by lightly tapping with a hammer.
ST 18675AA000 DIFFERENTIAL SIDE OIL
SEAL INSTALLER
8) Apply oil to the oil seal lips.
9) Install the front drive shaft. STALLATION, Front Drive Shaft.>
10) Install the front exhaust pipe. EX(H6DO)-5, INSTALLATION, Front Exhaust
Pipe.>
11) Lower the vehicle.
12) Pour gear oil into the gauge hole.
Recommended gear oil:
SPECIFICATION, General Description.>
Gear oil capacity:
1.3 — 1.5 2 ( 1 . 4 — 1 . 6 U S q t , 1 . 1 — 1 . 3 I m p q t )
13) Check the level of differential gear oil. 5AT-28, INSPECTION, Differential Gear Oil.>
(A) Oil pan
(B) Differential gear oil drain plug
(B)
AT-01362
(A)
AT-00029
ST

5AT-54
Control Valve Body
AUTOMATIC TRANSMISSION
4) Attach the magnet at the specified position of the
oil pan.
5) Apply liquid gasket to the oil pan.
Liquid gasket:
THREE BOND 1217B (Part No. K0877YA020)
6) Install the oil pan by equally tightening the bolts.
Tightening torque:
5 N·m (0.5 kgf-m, 3.7 ft-lb)
7) Pour ATF through the oil charge pipe.
Specified and recommended fluid:
SPECIFICATION, General Description.>
Capacity:
Fill with the same amount of ATF as drained.
8) Check the ATF level.

9) Perform Clear Memory 2 operation. 5AT(diag)-17, CLEAR MEMORY MODE, OPERA-
TION, Subaru Select Monitor.>
10) Perform the inspection with driving the vehicle
at the end of repair work, and make sure there is no
faulty as below;
•Excessive shift shock
•Oil leakage from the transmission body, etc.
•Occurrence of noise caused by interference etc.
NOTE:
If excessive shift shock is felt, execute advance op-
eration of learning control. PROCEDURE, Learning Control.>
C: INSPECTION
Check each parts for holes, damages or other for-
eign matters.
AT-01959
AT-03249