2009 SUBARU TRIBECA bulb

LI-16
Front Side Marker Light Bulb
LIGHTING SYSTEM
14.Front Side Marker Light Bulb
A: REMOVAL
1) Open the front hood.
2) Turn the socket (A) and remove the front turn
signal light bulb.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
1) Visually check the bulb for blow out.
2) Check the bulb specification.
tion.>
3) If NG, replace the bulb with a new one.
LI-00508
(A)

LI-18
Front Fog Light Bulb
LIGHTING SYSTEM
16.Front Fog Light Bulb
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Disengage the three clips, and then turn over the
lower mud guard.
3) Disconnect the harness connector.
4) Remove the back cover.
5) Remove the spring retainer (A), then detach the
fog light bulb.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
1) Visually check the bulb for blow out.
2) Check the bulb specification. SPECIFICATION, General Description.>
3) If NG, replace the bulb with a new one.
LI-00510
LI-00511
(A)

LI-20
Rear Combination Light Assembly
LIGHTING SYSTEM
18.Rear Combination Light As-
sembly
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the cover.
3) Remove the two bolts, and then detach the rear
combination light by pulling it to the rear side of ve-
hicle.
4) After turning the sockets of the tail/stop light
bulbs and rear turn signal light bulbs, remove the
rear combination light.
B: INSTALLATION
Install in the reverse order of removal.
LI-00512
LI-00513

LI-21
Tail/Stop Light Bulb
LIGHTING SYSTEM
19.Tail/Stop Light Bulb
A: REMOVAL
1. COMBINATION LIGHT
1) Remove the rear combination light assembly.
Assembly.>
2) Turn the socket and remove the bulb.
2. FINISHER LIGHT
1) Remove the bulb inspection cover of the rear
gate trim.
2) Turn the socket and remove the bulb.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
1) Visually check the bulb for blow out.
2) Check the bulb specification. SPECIFICATION, General Description.>
3) If NG, replace the bulb with a new one.
LI-00514
LI-00518

LI-22
Rear Turn Signal Light Bulb
LIGHTING SYSTEM
20.Rear Turn Signal Light Bulb
A: REMOVAL
1) Remove the rear combination light assembly.
Assembly.>
2) Turn the socket and remove the bulb.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
1) Visually check the bulb for blow out.
2) Check the bulb specification. SPECIFICATION, General Description.>
3) If NG, replace the bulb with a new one.
LI-00515

LI-23
Rear Side Marker Light Bulb
LIGHTING SYSTEM
21.Rear Side Marker Light Bulb
A: SPECIFICATION
The rear side marker light bulb is integrated into the
tail/stop light as a single unit; therefore, refer to the
section on tail/stop light bulbs for the removal pro-
cedures. Bulb.>

LI-24
Rear Finisher Light Assembly
LIGHTING SYSTEM
22.Rear Finisher Light Assembly
A: REMOVAL
1) Remove the bulb inspection cover of the rear
gate trim.
2) Disconnect the harness connector.
3) Remove the mounting nuts and detach the rear
finisher assembly.
B: INSTALLATION
Install in the reverse order of removal.
LI-00516
(A)
LI-00517

LI-25
Back-up Light Bulb
LIGHTING SYSTEM
23.Back-up Light Bulb
A: REMOVAL
1) Remove the bulb inspection cover of the rear
gate trim.
2) Turn the socket and remove the bulb.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
1) Visually check the bulb for blow out.
2) Check the bulb specification. SPECIFICATION, General Description.>
3) If NG, replace the bulb with a new one.