2009 SUBARU TRIBECA Reverse

LI-19
Side Turn Signal Light Assembly
LIGHTING SYSTEM
17.Side Turn Signal Light As-
sembly
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the mirror. MENT, Outer Mirror.>
3) Remove the scalp cap. PLACEMENT, Scalp Cap.>
4) Disconnect the harness connector, remove the 3
mounting screws and then remove the side turn
signal light assembly.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
1) Install the side turn signal light assembly and
check that it blinks normally.
2) If it does not blink normally, replace the side turn
signal light assembly with a new one.
NOTE:
Because a LED (Light Emitting Diode) is used for
the side turn signal light, replace the side turn sig-
nal light as an assembly if the LED does not turn
on.
LI-00293

LI-20
Rear Combination Light Assembly
LIGHTING SYSTEM
18.Rear Combination Light As-
sembly
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the cover.
3) Remove the two bolts, and then detach the rear
combination light by pulling it to the rear side of ve-
hicle.
4) After turning the sockets of the tail/stop light
bulbs and rear turn signal light bulbs, remove the
rear combination light.
B: INSTALLATION
Install in the reverse order of removal.
LI-00512
LI-00513

LI-21
Tail/Stop Light Bulb
LIGHTING SYSTEM
19.Tail/Stop Light Bulb
A: REMOVAL
1. COMBINATION LIGHT
1) Remove the rear combination light assembly.
Assembly.>
2) Turn the socket and remove the bulb.
2. FINISHER LIGHT
1) Remove the bulb inspection cover of the rear
gate trim.
2) Turn the socket and remove the bulb.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
1) Visually check the bulb for blow out.
2) Check the bulb specification. SPECIFICATION, General Description.>
3) If NG, replace the bulb with a new one.
LI-00514
LI-00518

LI-22
Rear Turn Signal Light Bulb
LIGHTING SYSTEM
20.Rear Turn Signal Light Bulb
A: REMOVAL
1) Remove the rear combination light assembly.
Assembly.>
2) Turn the socket and remove the bulb.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
1) Visually check the bulb for blow out.
2) Check the bulb specification. SPECIFICATION, General Description.>
3) If NG, replace the bulb with a new one.
LI-00515

LI-24
Rear Finisher Light Assembly
LIGHTING SYSTEM
22.Rear Finisher Light Assembly
A: REMOVAL
1) Remove the bulb inspection cover of the rear
gate trim.
2) Disconnect the harness connector.
3) Remove the mounting nuts and detach the rear
finisher assembly.
B: INSTALLATION
Install in the reverse order of removal.
LI-00516
(A)
LI-00517

LI-25
Back-up Light Bulb
LIGHTING SYSTEM
23.Back-up Light Bulb
A: REMOVAL
1) Remove the bulb inspection cover of the rear
gate trim.
2) Turn the socket and remove the bulb.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
1) Visually check the bulb for blow out.
2) Check the bulb specification. SPECIFICATION, General Description.>
3) If NG, replace the bulb with a new one.

LI-26
License Plate Light Assembly
LIGHTING SYSTEM
24.License Plate Light Assembly
A: REMOVAL
1) Remove the rear gate garnish. REMOVAL, Rear Gate Garnish.>
2) Disengage the clips, and disconnect the connec-
tors, and then detach the license lamp assembly.
B: INSTALLATION
Install in the reverse order of removal.
LI-00519

LI-27
License Plate Light
LIGHTING SYSTEM
25.License Plate Light
A: REMOVAL
1) Remove the license plate light mounting screw
(A) and then remove the lens (B).
2) Remove the bulb.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
1) Visually check the bulb for blow out.
2) Check the bulb specification. SPECIFICATION, General Description.>
3) If NG, replace the bulb with a new one.
LI-00520
(A)
(B)(B)
(A)