Instruments and Indicator/Warning Lights
31
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Turn signal system
Either the left
or right
indicator light flashes depending on the position of the turn
signal lever. The indicator light flashes at twice its normal rate if a turn signal light fails. This does not apply when towing a trailer. Switching off the hazard warning light system
is switched on will cause all of the turn
signal lights as well as both indicator lights to flash. Further information about the turn signal system
⇒page 59.
Fog lights*
The warning light
comes on when the fog lights are operating
⇒page 56.
Main beam
The indicator light
comes on when the main beam is selected or also when the
headlight flasher is operated. Further information about the main beam
⇒page 59.
Low beam
The warning light
comes on when low beam is selected
⇒page 53.
Rear fog light
The warning light
comes on when the rear fog lights are operating
⇒page 57.
Cruise control system*
The warning light
lights up, when operating the speed regulating system.
Bulb failure
The warning light
comes on if a bulb is faulty:
•
up to 2 seconds after the ignition is switched on;
•
when switching on the defective light bulb.
The following text e.g will be displayed in the information display*:
Check front right dipped beam!
The rear side lights and the licence plate lighting require several light bulbs. The indi- cator light
only lights up if all light bulbs of
the licence plate lighting or the parking
light (in one rear light unit) are defective.
Check regularly the function of the light
bulbs.Diesel particle filter*
(diesel engine)
If the warning light
comes on, this means that soot
has accumulated in the diesel
particle filter because of the frequent short distances. In order to clean the diesel particle filter, the vehicle should be driven at an even speed of at least 60 km/h at engine speeds of 1
800 - 2 500 rpm for at least 15 minutes or until
the warning light goes out with the 4th or
5th gear engaged (automatic gearbox: posi-
tion S) when the traffic situation permits it. This increases the exhaust temperature and the soot deposited in the diesel particle filter is burnt. Always pay attention to the valid speed limits
⇒
.
The warning light
goes out after the successful cleaning of the diesel particle filter.
If the filter is not properly
cleaned, the warning light
does not go out and the
warning light
begins to flash. In the in
formation display* appears
Diesel-particle
Owner's manual
. Afterwards the engine control unit shifts the engine into the emer-
gency mode, which only has a reduced power
output. After switchin
g the ignition off
and on again the warning light
comes on.
Have the vehicle inspected without
delay by your specialist garage.
sgg.6.book Page 31 Thursday, September 24, 2009 2:32 PM
Lights and Visibility
58Headlamp range adjustment
Once the low beam is switched on
you can then adapt the range of the
headlights to the lo
ad of the vehicle.
– Turn the control dial
⇒fig. 48
until you have adjusted the low beam so that
oncoming traffic is not dazzled.
Settings The positions correspond
approximately to the
following vehicle loads:
Front seats occupied, luggage compartment empty. All seats occupied, luggage compartment empty. All seats occupied, luggage compartment laden.Driver seat occupied, lu
ggage compartment laden.
Caution
Set the headlight beam adjustment in such
a way as to avoid dazzling oncoming traffic.
Note
Headlights fitted with Xenon bulbs* adapt
automatically to the load and driving state
of the vehicle (e.g. accelerating, braking) wh
en the ignition is switched on and when
driving. Vehicles which are equipped with
Xenon bulbs* do not have a manual head-
light range adjustment control.
Switch for hazard warning lights
– Press switch
⇒fig. 49
to switch the hazard warning light system on or off.
All the turn signal lights on the vehicle flas
h at the same time when the hazard warning
light system is switched on. The indicator light for the turn signals and the indicator light in the switch also flash at the same time. You can also switch on the hazard warning light system if the ignition is switched off. The hazard warning light system is switched
on automatically if an airbag is deployed
in the event of an accident. Please comply with any legal requirements when using the hazard warning light system.
Note
Switch on the hazard warning light system if, for example:•
you encounter traffic congestion,
•
your vehicle breaks down or an emergency situation occurs.
Fig. 48 Dash panel: Lights and Visibility
A-A1A2A3
Fig. 49 Dash panel: Switch for hazard warning lights
sgg.6.book Page 58 Thursday, September 24, 2009 2:32 PM
Lights and Visibility
59
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
The turn signal
and main beam lever
The parking lights and headlight flas
her are also switched on and off
using the turn signal and main beam lever.The turn signal and main beam le
ver perform the following functions:
Right
and left
turn signal light
– Push the lever upwards or downwards
⇒fig. 50
.
– If you only wish to flash three times* (the
so-called convenience turn signal), push
the lever briefly up to the upper or lower pr
essure point and release it. This function
can be activated/deactivated in the information display*
⇒page 24.
– Turn signal for changing lanes - in order to
only flash briefly, move the lever up or
down to the pressure point and hold it in this position.
Main beam
– Switch on the low beam. – Push the lever forwards.– Pull the lever back into the initial positi
on in order to switch the main beam off
again.
Headlight flasher
– Pull on the lever of the steering whee
l (sprung position) -
the main beam and
warning light in the instrument cluster come on.
Parking light
– Switch off the ignition. – Push the lever up or down - the right-hand
or left-hand parking light is switched
on.
Information concerning the function of the lights•
The
turn signal system
only operates when the ignition is switched on. The corre-
sponding indicator light
or in the instrument cluster also flashes.
•
The turn signal is automatically cancelled after negotiating a curve.
•
The indicator light flashes at twice its normal
rate if a bulb of the turn signal light
fails.•
The side light and rear light on the appropriate side of the vehicle are switched on
when the
parking light
is selected. The parking light only operates if the ignition is
switched off.
Caution
Use main beam or the headlight flasher only
if this does not risk dazzling other road
users.
Note
•
If you have switched on the right or left turn signal light and you switch off the igni-
tion, the parking light is not automatically switched on.•
Use only in accordance with the legal
requirements the described lighting and
signal systems.
Fig. 50 Turn signal and main beam lever
sgg.6.book Page 59 Thursday, September 24, 2009 2:32 PM
Fuses and light bulbs
234
Fuse cover in engine compartment The fuse box in the engine compartment exists in two different versions. You can determine which version your vehicle is fitted with after removing the fuse cover at
the location of the fuses.
On some vehicles, the battery cover must be removed before removing the fuse cover ⇒ page 210.Removing fuse cover– Move the circlips
⇒fig. 193
as far as the stop, the symbol
appears behind the
circlip and remove the cover.
Installing fuse cover– Position the fuse cover on the fuse box and
push the circlips as far as the stop -
the symbol
is visible behind the circlip.
Caution
•
When unlocking and locking the fuse cover, it must be pressed on the sides to the
box, otherwise damage can occur to the locking mechanism.•
Carefully position the fuse
cover in the engine compartment. If the cover was not
correctly positioned, water can get into the
fuses and this results in a damage to the
vehicle!
Fuse assignment in engine compartment - version 1Certain electrical components are only stan
dard on certain vehicle model versions or
only suppliable as optional
equipment for certain models.
Fig. 193 Fuse cover in engine compart- ment
AA
AA
No.
Power consumer
Amperes
F1
Central control unit, right main headlight, right rear light unit
30
F2
Valves for ABS
20
F3
Not assigned
F4
Measuring circuit
5
F5
Horn
15
F6
Not assigned
F7
Valve for fuel dosing
15
F8
Not assigned
F9
Activated charcoal filter, ex
haust gas recirculation valve
10
F10
Leakage diagnosis pump
10
F11
Lambda probe upstream of catalytic converter, engine control unit
10
F12
Lambda probe downstream
of catalytic converter
10
F13
Control unit for automatic gearbox
15
Fig. 194 Schematic representation of fuse box in engine compartment - version 1
sgg.6.book Page 234 Thursday, September 24, 2009 2:32 PM
Fuses and light bulbs
235
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
F14
Not assigned
F15
Coolant pump
10
F16
Not assigned
F17
Instrument cluster, windshield
wiper lever and turn signal
light lever
5
F18
Audio amplifier (sound system)
30
F19
Radio
15
F20
Phone
5
F21
Not assigned
F22
Not assigned
F23
Engine control unit
10
F24
Control unit for CAN databus
5
F25
Not assigned
F26
Not assigned
F27
Not assigned
F28
Engine control unit
15
F29
Actuation for coolant pump after-running
5
F30
Control unit for auxiliary heating
20
F31
Front window wiper
30
F32
Not assigned
F33
Not assigned
F34
Not assigned
F35
Not assigned
F36
Not assigned
F37
Not assigned
F38
Radiator fan, valves
10
No.
Power consumer
Amperes
F39
Clutch pedal switch, brake pedal switch
5
F40
Ignition coils
20
F41
Not assigned
F42
Actuation of fuel pump
5
F43
Not assigned
F44
Not assigned
F45
Not assigned
F46
Not assigned
F47
Central control unit, left main headlight, left rear light unit
30
F48
Pump for ABS
40
F49
Power supply for terminal 15 (ignition on)
40
F50
Not assigned
F51
Not assigned
F52
Power supply relay - terminal X
a)
40
F53
Accessory equipment
50
F54
Not assigned
a)In order not to drain the battery unnecessarily wh
en starting the engine
, the electrical compo-
nents of this terminal are automatically switched off.No.
Power consumer
Amperes
sgg.6.book Page 235 Thursday, September 24, 2009 2:32 PM
Fuses and light bulbs
236
Fuse assignment in engine compartment - version 2Certain electrical components are only standard on certain vehicle model versions or only suppliable as optional
equipment for certain models.
No.
Power consumer
Amperes
F1
Not assigned
F2
Control unit for automatic gearbox DQ 200
30
F3
Measuring circuit
5
F4
ABS control unit
20
F5
Control unit for automatic gearbox
15
F6
Instrument cluster, windshield
wiper lever and turn signal
light lever
5
F7
Power suppy terminal 15, Starter
40
F8
Radio
15
F9
Phone
5
F10
Engine control unit, Main relay
5/10
F11
Control unit for auxiliary heating
20
F12
Control unit for CAN databus
5
F13
Engine control unit
15/30
F14
Ignition
20
Fig. 195 Schematic representation of fuse box in engine compartment - version 2
F15
Lambda probe, fuel pump relay glow plug system relay
155
F16
Central control unit, right main headlight, right rear light unit
30
F17
Horn
15
F18
Amplifier for digital sound processor
30
F19
Front window wiper
30
F20
Control valve for fuel pressure
20
F21
Lambda probe
10/15
F22
Clutch pedal switch, brake pedal switch
5
F23
Coolant pump charge pressure control soleno
id valve, changeover valve
for radiator
5 10
F24
Activated charcoal filter, ex
haust gas recirculation valve
10
F25
ABS control unit
40
F26
Central control unit, left main
headlight, left rear light unit
30
F27
Glow plug system
50
F28
Not assigned
F29
Power supply of the interior
50
F30
Te r m i n a l X
a)
40
a)In order not to drain the battery unnecessarily wh
en starting the engine, the electrical compo-
nents of this terminal are automatically switched off.No.
Power consumer
Amperes
sgg.6.book Page 236 Thursday, September 24, 2009 2:32 PM
Fuses and light bulbs
237
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Fuse assignment in the dash panelCertain electrical components are only standard on certain vehicle model versions or only suppliable as optional
equipment for certain models.
No.
Power consumer
Amperes
1
Heating of the gearbox ve
ntilation (diesel engine)
Control unit for automatic gearbox DQ200
1010
2
To w i n g d e v i c e
20
3
To w i n g d e v i c e
15
4
Not assigned
5
Air blower for heating, radiat
or fan, air conditioning sys-
tem, Climatronic
40
6
Rear window wiper
15
7
Not assigned
8
To w i n g d e v i c e
15
9
Central control unit - interior lights
10
10
Rain sensor, light switch, diagnostic socket
10
11
Left side cornering lights
10
12
Right side cornering lights
10
13
Radio, changer for mobile navigation
15
Fig. 196 Schematic representation of the fuse carrier in the dash panel
14
To w i n g d e v i c e
5
15
Light switch
5
16
Heatable washing nozzles, regulator for seat heating
5
17
Control unit for headlamp be
am adjustment and head-
light swivel
5
18
Diagnostic socket, engine
control unit, brake sensor
10
19
Control unit for ABS, ESP, swit
ch for tyre air pressure con-
trol, control unit for parking aid, switch for Offroad mode
5
20
Switch and control unit for airbag
5
21
WIV, parking light, dimming mirrors, pressure sensor, tele- phone preinstallation, air mass meter
5
22
Instrument cluster, control
unit for electromechanical
power steering, Haldex
5
23
Central locking system and bonnet lid
15
24
Rear power window
30
25
Rear wind
ow heater
Rear window he
ater, Auxiliary heating (auxiliary heating
and ventilation)
25 30
26
Power socket in the luggage compartment
20
27
Electric sliding/tilting roof, electric sun screen
30
28
Fuel pump relay, control unit for fuel pump, injection valves
15
29
Front power window
30
30
front and rear lighter
20
31
Headlight cleaning system
20
32
Front seat heating
20
33
Heating, Climatic, Climatronic
7,5
No.
Power consumer
Amperes
sgg.6.book Page 237 Thursday, September 24, 2009 2:32 PM
Fuses and light bulbs
238
For power consumers, e.g. the radio, which ca
n be operated with the ignition switched
off as long as the ignition key is not withdrawn. Electrically adjustable seats are protected by
automatic circuit breakers
, which
switch on again automatically after a few seconds after the overload has been eliminated.BulbsChanging bulbsThe relevant lamp must always be switch
ed off before a light bulb is replaced.
Defect light bulbs should only be replaced
with light bulbs of the same type. The desig-
nation is located on the ligh
t socket or the glass bulb.
Changing certain bulbs is not something whic
h you can do yourself, but requires to be
done by a specialist. Other parts of the vehicle must be removed in order to change the light bulbs. This applies, in particular, to
bulbs which can only be reached from the
engine compartment. We therefore recommend that you have any
bulbs changed by a specialist garage or,
in exceptional cases, by calling
on other professional assistance.
Please note that the engine compartment is a hazardous area
⇒page 204, “Working
in the engine compartment”. We recommend that you always have a small box of replacement bulbs in your vehicle. You can obtain replacement bulbs from Škoda
original accessories or from a specialist
garage
18).
The set of light bulbs can be stowed
in the box in the luggage compartment.
Fitted with a xenon headlightChange of bulbs on vehicles with Xenon lights (low beam lights, parking lights and main beam lights) should be undertaken by a specialist garage. Bulb - Overview
34
Alarm, spare horn
5
35
Control unit for automatic gearbox DQ200
10
36
Not assigned
18)The small box with replacement bulbs is part of
the basic equipping of th
e vehicle in some coun-
tries.No.
Power consumer
Amperes
Front headlight
Halogen headlight
Xenon headlight
Low beam light
H4
D1S
Main beam light
H4
D1S
Parking lights
W5W
W5W BL
Daylight driving lights
P13W
Turn signals
HPC24WY
Fog lights
H7
Rear light unit
Bulb
Reversing lights, brake lights and rear fog light
P21W
Turn signals
PY21W
Parking lights
W5W
Others
Bulb
Licence plate light
C5W
3. Brake light
LED
Entry lighting
W5W
front interior lighting
W5W
Reading lights
W5W
Rear interior lighting
C5W
sgg.6.book Page 238 Thursday, September 24, 2009 2:32 PM