2009 SKODA YETI display

Instruments and Indicator/Warning Lights
22Outside temperatureThe outside temperature appears in the disp
lay when the ignition is switched on.
If the outside temperature drops below +4°C, a snow flake symbol (warning signal for ice on the road) appears in front of the
temperature indicator and flashes for 10
seconds, then remains displayed together with the outside temperature
⇒fig. 20
. At
the same time an audible signal sounds. Af
ter pressing the rocker switch at the
windshield wiper lever
⇒page 21, fig. 19
or the button at the multifunction
steering wheel
⇒page 21, fig. 19
, the function shown last is indicated.
WARNING
Do not only rely upon the information given on the outside temperature display that there is no ice on the road. Please note that black ice may also be present on the road surface even at temperatures around +4°C - warning, drive with care!Driving timeThe driving time which has elapsed since the memory was last erased, appears in the display. If you wish to measure the driving ti
me as of a particular time, you must set the
memory to zero at this moment in time by
pressing the button on the windshield
wiper lever
⇒page 21, fig. 19
or the handwheel on the multifunction steering
wheel*
⇒page 21, fig. 19
for longer than 1 second.
The maximum distance indicated in both
memories is 99 hours and 59 minutes. The
indicator is set back to null
if this period is exceeded.
Current consumptionThe current fuel consumption level is shown in
the display in litres/100 km. This infor-
mation can help you to adapt your style of
driving to the fuel co
nsumption you wish to
achieve. The display appears in litres/hour if the vehicle is stationary or driving at a low speed.The indicated value will be updated every 0.5 seconds while you are driving.Average fuel consumptionThe average fuel consumption since the memory was last erased is shown in the display in litres/100 km
⇒page 20, fig. 18
. This information can help you to adapt your
style of driving to the fuel co
nsumption you wish to achieve.
If you wish to determine the average fuel
consumption over a certain period of time
you must set the memory to zero at the start of the measurement using the button on the windshield wiper lever
⇒page 21, fig. 19
or with the handwheel on the
multifunction st
eering wheel*
⇒page 21, fig. 19
. A zero appears in the display for the
first 100 m you drive after erasing the memory. The indicated value will be updated every 5 seconds while you are driving.
Note
The amount of fuel consumed will not be indicated.RangeThe estimated range in kilometres is shown on the display. It indicates the distance you can still drive with your vehicle based on th
e present level of fuel in the tank for the
same style of driving. The readout is shown in steps of 10 km. After lighting up of the indicator light for the fuel reserve the display is shown in steps of 5 km. The fuel consumption for the last 50 km is taken as a basis for calculating the range. If you drive in a more economical manner from this moment on, the range will be increased accordingly.
Fig. 20 The outside temperature
AA
AC
AB
AD
AB
AD
sgg.6.book Page 22 Thursday, September 24, 2009 2:32 PM

Instruments and Indicator/Warning Lights
23
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
If the memory is set to zero (after disco
nnecting the battery), th
e fuel consumption of
10 ltr./100 km is calculated for the range; afterwards the value is adapted accordingly to the style of driving.Distance drivenThe distance driven since the memory was last erased appears in the display ⇒ page 20. If you wish to measure the distance
driven of a particular time, you must
set the memory to zero at this moment in time by pressing the button on the wind- shield wiper lever
⇒page 21, fig. 19
or the handwheel on the multifunction
steering wheel*
⇒page 21, fig. 19
.
The maximum distance indicated in both switch positions is 9.999 km. The indicator is set back to null if this
period is exceeded.
Average speedThe average speed since the memory was last erased is shown in the display in km/hour
⇒page 20. If you wish to determine the average vehicle speed over a certain
period of time you must set the memory to zero at the start of the measurement using the button on the windshield wiper lever
⇒page 21, fig. 19
or with the handwheel
on the multifunction steering wheel*
⇒page 21, fig. 19
.
A zero appears in the display for the first 100 m you drive after erasing the memory.The indicated value will be updated every 5 seconds while you are driving.Current speed*The current speed which is identical to the display of the speedometer, is indicated on the display
⇒page 16, fig. 15
.
Oil temperatureThe oil temperature appears in the display when the ignition is switched on. If there is a fault, three lines are displayed instead of the temperature.
Warning against excessive speeds*Fig. 21 Warning against excessive speeds / mu
lti-functional indicator: Control elements
This function enables you to set a speed limit, e.g. if you drive in town. A text in the display is intended to draw your attention
to the fact that you have exceeded the set
speed limit.Warning against excessive speeds– Select the menu point
Speed warning --- km/h (warning at --- km/h).
.
– Drive e.°g at a speed of 50 km/h. – Press the button on the windshield wiper lever
⇒fig. 21
or the handwheel
on the multifunction steering wheel*
⇒page 21, fig. 19
. Speed warning 50 km/h
(warning at 50 km/h)
is displayed in the information display*
⇒fig. 21
. You can
increase or reduce this value with the
button on the windshield wiper lever or
by turning the handwheel on the multifunction steering wheel*.
– The value is stored by repeated pressing
of the button on the windshield wiper
lever or the handwheel on the multifunction steering wheel*.
If you now exceed th
e set speed limit,
Speed 50°km/h exceeded
will be shown on the
display. This message is indicated for as long as the speed is reduced below the set limit or switch off the message by pressing the button on the windshield wiper lever ⇒ fig. 21
or the handwheel on the mu
ltifunction steering wheel*
⇒page 21,
fig. 19
.
An audible signal sounds as an additional warning signal.The set speed limit remains stored even after switching off the ignition.
AB
AD
AB
AD
A2
AB
AD
AA
AD
AB
AD
AB
AD
sgg.6.book Page 23 Thursday, September 24, 2009 2:32 PM

Instruments and Indicator/Warning Lights
24Information display*IntroductionThe information display provides you with information in a convenient way concerning the
current operating state of your vehicle
. The information system also
provides you with data (depending on the equipment installed in the vehicle) relating to the radio, mobile phone, multi-function
al indicator, naviga
tion system, the unit
connected to the MDI input and the automatic gearbox. Certain functions and operating conditions
are always being checked on the vehicle
when the ignition is switched on and also while driving. Functional faults, if required
repair work and other information are indicated by red
symbols
⇒page 26 and yellow symbols
⇒page 27.
Lighting up of certain symbols is combined with an acoustic warning signal.Information and texts giving warnings
are also shown in the display
⇒page 29.
The display of text is possible in the following languages:
Czech, English, German, French, Italian,
Spanish, Portuguese, Russian and Chinese.
You can select the desired language in the setting menu.The following information can be shown in
the display (depending on the equipment
installed on the vehicle):
Caution
Pull out the ignition key while having co
ntact with the display (for example when
cleaning) in order to prevent any damage.Main menuFig. 23 Information display: Controls on the wi
ndshield wiper lever /
controls on the multi-
function steering wheelOperating with the buttons on the windshield wiper lever– You can activate the
MAIN MENU
by pressing the rocker switch
⇒fig. 23
for
more than 1 second.
– You can select indi
vidual menu points by means of the rocker switch . When the
pushbutton is briefly pressed, the info
rmation you have selected is displayed.
Operating with the buttons on the multifunction steering wheel*– You can call up the
MAIN MENU
by pressing the button
⇒fig. 23
.
Fig. 22 Instrument cluster: Information display
Main menu
⇒ page 24
Door, luggage compartment door and bonnet ajar warn- ing
⇒ page 25
Service Interval Display
⇒page 18
Selector lever positions for the automatic gearbox DSG
⇒page 122AAAA
AB
AC
sgg.6.book Page 24 Thursday, September 24, 2009 2:32 PM

Instruments and Indicator/Warning Lights
25
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
– You can select the individual menus by
pressing the handwheel . After briefly
pressing the handwheel , th
e desired menu is indicated.
– After briefly pressing the button you can achieve a higher level, by pressing the
button for longer than 1 second, you can call up the
MAIN MENU
.
You can select the following information (d
epending on the equipment installed on
the vehicle):„
MFD (Onboard computer)
⇒page 20
„
Audio
*
„
Navigation
*
„
Phone
* ⇒page 129
„
Aux. Heating (auxiliary heating)
* ⇒page 105
„
Assistant
* ⇒page 55
„
Vehicle status
⇒page 26
„
Setup
⇒page 27
The menu point
Audio
is only then displayed when
the factory-fitted Radio* is
switched on. The menu point
Navigation
is only then displayed when the factory-fitted Navigation
system* is switched on. The menu point
Aux. Heating
is only then displayed, if
the vehicle is fitted with the
factory-fitted auxiliary heating*. The menu point
Assistant
is only then displayed, if the
vehicle is fitted with cornering
lights*.
Note
•
If warning messages are shown in the information display
⇒page 25
⇒page 26,
these messages can be confirmed with the bu
tton on the windshield wiper lever or
with the button on the multifunction steering wheel in order to call up the main menu.•
If you do not activate the information display at that moment, the menu shifts to
one level higher every 10 seconds.
•
The operation of the factory-fitted radio*
or the navigation system* is described in
separate operating instructions to be
found in the on-board literature.
Door, luggage compartment door and bonnet ajar warningThe door, luggage compartment and bonnet ajar
warning lights up if at least one door,
the luggage compartment or bonnet are not closed. The symbol indicates which door is still open or whether the luggage
compartment door or bonnet is
not closed

⇒ fig. 24
.
The symbol goes out as soon as the doors,
luggage compartment door and bonnet are
completely closed. A warning signal sounds if the car is driven at a speed of more than 6km/hour and if the engine or the luggage compartment door is open.
AD
AD
AC
AC
AB
AD
Fig. 24 Information display: Door warning
sgg.6.book Page 25 Thursday, September 24, 2009 2:32 PM

Instruments and Indicator/Warning Lights
26Auto Check Control*Car stateThe Auto Check Control carries out a chec
k of certain functions and vehicle compo-
nents. The check is performed constantly when
the ignition is switched on, both when
the vehicle is stationary, as well as when driving. Some operational faults, urgent repairs, se
rvice work or other information appear in
the display of the instrument cluster. The di
splays are shown with a red or yellow light
symbol depending on the priority of the message. The red symbols indicate
danger
(priority 1) while the yellow symbols indicate a
warning
(priority 2). Information for the driver
may also appear in addition to the
symbols
⇒page 29.
Shown in the menu
Vehicle status
, if there is at least one error message. After selecting
this menu the first of the error messages is displayed. Several error messages are shown on the display under the message e.°g.
1/3
⇒fig. 25
. This indicates that the first
of a total of three error messages is displayed. The respective messages are displayed one after the other in an interval of 5 second
s. Check as soon as possible the displayed
error messages. As long as the operational faults are not
rectified, the symbols are always indicated
again. After the first display, the symbol
s are indicated without information for the
driver. If a fault occurs, a warning signal will also
sound in addition to the symbol and text in
the display:
•
Priority 1 - three warning signals
•
Priority 2 - one warning signal
Red symbols A red symbol signals danger.– Bring the vehicle to a stop. – Switch the engine off.– Investigate the function indicated. – Obtain professional assistance. Meaning of the red symbols: Three
successive warning signals will sound if a red symbol appears.
Fig. 25 Information display: Display of operational fault

Engine oil pressure too low
⇒ page 33

Overheated clutches of the automatic gear- box DSG*
⇒ page 38
Fig. 26 Information display: Oil pressure is low
sgg.6.book Page 26 Thursday, September 24, 2009 2:32 PM

Instruments and Indicator/Warning Lights
27
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Yellow symbols A yellow symbol signals a warning.Check the relevant function as soon as possible. The meaning of the yellow symbols: One
warning signal will sound if a yellow symbol appears.
If several operational faults
of priority 2 exist, the symbols appear one after the other
and are each illuminated for about 5 seconds.
Set-upYou can change certain settings by means
of the information display. The current
setting is shown on the information display in the respective menu at the top below the line
⇒fig. 28
.
You can select the following information (d
epending on the equipment installed on
the vehicle):•
Language
•
MFD Data (MFA DATA)
•
Convenience
•
Lights & Vision (Lights & Vision)
•
Time
•
Winter tyres
•
Units
•
Assistant (Assistant)
•
Alternative speed displayed (Second speed)
•
Tra v e l m o d e
•
Service Interval (Service)
•
Factory Setting
•
Back
After selecting the menu point
Back
you will reach one level higher in the menu.

Check engine oil level, engine oil sensor faulty
⇒ page 205

Brake pad worn
⇒page 36
Fig. 27 Information display: Brake pad worn
Fig. 28 Setting the clock
sgg.6.book Page 27 Thursday, September 24, 2009 2:32 PM

Instruments and Indicator/Warning Lights
28Language Here you can set in which language the warning and information texts should be displayed. Displays of the MFA Here you can switch off or on certain di
splays of the multi-
functional indicator.
Comfort* You can set the following functions (depen
ding on the equipment installed on the
vehicle):
Lights and Visibility Here you can set how long the light should
stay on for the func
tion Coming/Leaving
Home. Furthermore you can here switch on or
off the function daylight driving lights
and convenience turn signal. After selecting the menu point
Factory setting
the factory setting of the lighting is
established again. Time Here you can set the time, the time format
(12 or 24 hour indicator) and the time
change summer/winter time. Winter tyres Here you can set at which speed a warning signal should sound. This function is used for e.g winter tyres with the permissible maximum speed less than the maximum speed of the vehicle. When exceeding the speed, the following is displayed on the information display*:
Snow tyres max. speed ... km/h (Winter tyres maximum ... km/h)
Measures Here you can set the units for temperat
ure, consumption and distance driven.
Assistant Here you can adjust the tones of the
acoustic signals of the parking aid*.
Second speed Here you can switch on the display of the second speed in mph or in km/h
2).
Tra v e l m o d e Here you can activate / deactivate the mode “tourist light”. This mode makes it possible to drive in countries with opposing traffi
c system, driving on the left/right, without
dazzling the oncoming vehicles. The headligh
t swivel function is deactivated when
switching on this mode. Further information
⇒page 56.
Rain closing
On vehicles with rain sensor you can switch on or off the function for automatic closing of the windows and the sliding/tilting roof in case of ra
in and locked vehicle. If it is
not raining and the function is
set, the windows including
the sliding/tilting roof are closed automatically after approx. 12 hours.
Door open
Here you can switch on or off the functions for opening a single door and automatic closing.
ATA c o n fi r m
Here you can set if a signal to
ne should sound additionally
when activating or deactivating the anti-theft alarm sys- tem.
Window op.
Here you can set the convenience mode only for the driver window or for all the windows.
Mirror down
Here you can switch on or off the function for mirror low-ering on the front passenger side when engaging the reverse gear
a).
Mirror adjust.
Here you can switch on or off the function for left and right exterior mirror adjustment simultaneously.
Fa cto r y se tt ing

After selecting this menu the convenience setting is reset to factory setting. The following is displayed in the infor- mation display: Factory setting for convenience is set
a)This function is only available on vehicles wi
th an electrically adjustable driver seat.
2)Valid for countries where the values ar
e indicated in British measuring units.
sgg.6.book Page 28 Thursday, September 24, 2009 2:32 PM

Instruments and Indicator/Warning Lights
29
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Service Here you can have the kilometers still to
be driven and the days until the following
service interval shown and the Service Interval Display reset.
Factory Setting After selecting the menu point
Factory Setting
the factory setting of the information
display is established again.
Warning lightsOverview The warning lights indicate certain functions or faults.
Fig. 29 Instrument cluster with warning lights

Turn signal lights (to the left)
⇒page 31

Turn signal lights (to the right)
⇒page 31

Fog lights*
⇒page 31

Main beam light
⇒page 31

Low beam light
⇒page 31

Rear fog light
⇒page 31

Speed regulating system*
⇒page 31
sgg.6.book Page 29 Thursday, September 24, 2009 2:32 PM