2009 SKODA YETI sensor

The brief instruction
13
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Switching lights on and offFurther information
⇒page 53, “Switching
lights on and off
”.
Turn signal and main beam lever Turn signal light right Turn signal light left Switching over between low beam and main beam lights Headlight flasherFurther information
⇒page 59, “The turn signal
  and main beam lever
”.
Windscreen wiper lever Intermittent switch, sensitivity setting rain sensor* Wipers off Intermittent wipe

Automatic light control*

Switching off all lights/daylight driving lights

Switching on side lights

Switching on the low beam and main beam

Fog lights*

Rear fog light
Fig. 7 Dash panel: Light switch
Fig. 8 Turn signal and main beam lever
AAABACAD
Fig. 9 Windscreen wiper lever
AAA0A1
sgg.6.book Page 13 Thursday, September 24, 2009 2:32 PM

Instruments and Indicator/Warning Lights
27
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Yellow symbols A yellow symbol signals a warning.Check the relevant function as soon as possible. The meaning of the yellow symbols: One
warning signal will sound if a yellow symbol appears.
If several operational faults
of priority 2 exist, the symbols appear one after the other
and are each illuminated for about 5 seconds.
Set-upYou can change certain settings by means
of the information display. The current
setting is shown on the information display in the respective menu at the top below the line
⇒fig. 28
.
You can select the following information (d
epending on the equipment installed on
the vehicle):•
Language
•
MFD Data (MFA DATA)
•
Convenience
•
Lights & Vision (Lights & Vision)
•
Time
•
Winter tyres
•
Units
•
Assistant (Assistant)
•
Alternative speed displayed (Second speed)
•
Tra v e l m o d e
•
Service Interval (Service)
•
Factory Setting
•
Back
After selecting the menu point
Back
you will reach one level higher in the menu.

Check engine oil level, engine oil sensor faulty
⇒ page 205

Brake pad worn
⇒page 36
Fig. 27 Information display: Brake pad worn
Fig. 28 Setting the clock
sgg.6.book Page 27 Thursday, September 24, 2009 2:32 PM

Instruments and Indicator/Warning Lights
28Language Here you can set in which language the warning and information texts should be displayed. Displays of the MFA Here you can switch off or on certain di
splays of the multi-
functional indicator.
Comfort* You can set the following functions (depen
ding on the equipment installed on the
vehicle):
Lights and Visibility Here you can set how long the light should
stay on for the func
tion Coming/Leaving
Home. Furthermore you can here switch on or
off the function daylight driving lights
and convenience turn signal. After selecting the menu point
Factory setting
the factory setting of the lighting is
established again. Time Here you can set the time, the time format
(12 or 24 hour indicator) and the time
change summer/winter time. Winter tyres Here you can set at which speed a warning signal should sound. This function is used for e.g winter tyres with the permissible maximum speed less than the maximum speed of the vehicle. When exceeding the speed, the following is displayed on the information display*:
Snow tyres max. speed ... km/h (Winter tyres maximum ... km/h)
Measures Here you can set the units for temperat
ure, consumption and distance driven.
Assistant Here you can adjust the tones of the
acoustic signals of the parking aid*.
Second speed Here you can switch on the display of the second speed in mph or in km/h
2).
Tra v e l m o d e Here you can activate / deactivate the mode “tourist light”. This mode makes it possible to drive in countries with opposing traffi
c system, driving on the left/right, without
dazzling the oncoming vehicles. The headligh
t swivel function is deactivated when
switching on this mode. Further information
⇒page 56.
Rain closing
On vehicles with rain sensor you can switch on or off the function for automatic closing of the windows and the sliding/tilting roof in case of ra
in and locked vehicle. If it is
not raining and the function is
set, the windows including
the sliding/tilting roof are closed automatically after approx. 12 hours.
Door open
Here you can switch on or off the functions for opening a single door and automatic closing.
ATA c o n fi r m
Here you can set if a signal to
ne should sound additionally
when activating or deactivating the anti-theft alarm sys- tem.
Window op.
Here you can set the convenience mode only for the driver window or for all the windows.
Mirror down
Here you can switch on or off the function for mirror low-ering on the front passenger side when engaging the reverse gear
a).
Mirror adjust.
Here you can switch on or off the function for left and right exterior mirror adjustment simultaneously.
Fa cto r y se tt ing

After selecting this menu the convenience setting is reset to factory setting. The following is displayed in the infor- mation display: Factory setting for convenience is set
a)This function is only available on vehicles wi
th an electrically adjustable driver seat.
2)Valid for countries where the values ar
e indicated in British measuring units.
sgg.6.book Page 28 Thursday, September 24, 2009 2:32 PM

Instruments and Indicator/Warning Lights
33
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
WARNING
Contact your specialist
garage if the power steering is defective.
Note
•
If the yellow warning light
 goes out after starting the engine again and a short
drive, it is not necessary to visit a specialist garage.•
If the battery has been di
sconnected and reconnected, the yellow warning light

comes on after switching on the ignition. Th
e warning light must go out after driving a
short distance.Engine oil pressure

The warning light

comes on for a few seconds
3) when the ignition is switched on.
Stop the vehicle and switch the engine off
if the warning light does not go off after
the engine has started or flashes while driving. Check the oil level and top up with oil as necessary
⇒page 206, “Replenishing engine oil”.
An audible signal sounds three times as an additional warning signal.Do not continue your journey
if for some reason it is not possible under the condi-
tions prevailing to top up with oil.
Keep the engine switched off
and obtain profes-
sional assistance from a specialist garage, otherwise it could lead to severe engine damage. Do not drive any further
if the warning light flashes even
if the oil is at the correct
level. Do not run the engine
not at idling speed either. Contact the nearest specialist
garage to obtain professional assistance. The following text will be displayed in the information display*:
Oil Pressure Engine off! Owner's manual!
WARNING
•
If you must stop for technical reasons, then park the vehicle at a safe
distance from the traffic and switch of
f the engine and switch on the hazard
warning light system.•
The red oil pressure light

is not an oil level indicator! One should there-
fore check the oil level at regular inte
rvals, preferably after every refueling
stop.Engine oil level

Warning light

lights up
If the warning light

lights up, the quantity of oil in
the engine is probably too low.
Check as soon as possible the oil level or top up
⇒page 206 with engine oil.
A peep sounds as an additional warning signal.The following text will be displayed in the information display*:
Check oil level!
The warning light will go out if the bonnet is
left open for more than 30 seconds. If no
engine oil has been replenished, the warning light will come on again after driving about 100 km. Warning light

flashes
A fault on the engine oil level sensor is indicated additionally by an audible signal and the warning light coming on several times after the ignition has been switched on. In this case have the engine inspecte
d without delay by a specialist garage.
The following text will be displayed in the information display*:
Oil sensor Workshop!
EPC fault light

(petrol engine)
The
 (Electronic Power Control) warning light comes on for a few seconds when the
ignition is switched on.
3)The warning light
 on vehicles fitted with information display does not come on after switch-
ing the ignition on, but only if a fault exists or the engine oil level is too low.
sgg.6.book Page 33 Thursday, September 24, 2009 2:32 PM

Lights and Visibility
54 Switching on daylight driving lights– Switch on the ignition without turning the light switch out of the position 0.Deactivating the function daylight driving lights– Pull the turn signal light lever towards the steering wheel up to 3 seconds after
switching on the ignition and at the same time, slide it to the bottom and hold it in this position for at least 3 seconds.
Activating the function daylight driving lights– Pull the turn signal light lever towards the steering wheel up to 3 seconds after
switching on the ignition and at the same time, slide it to the top and hold it in this position for at least 3 seconds.
When the daylight driving lights are switch
ed on, the side lights and the low beam
come on together. In some countries, the national legal provisions require that the parking lights come on together with the bulbs for daylight driving lights when activating the function daylight driving lights. On vehicles which are fitted with bulbs for daylight driving lights in the fog lights, the parking lights do not come on when activa
ting the function dayl
ight driving lights.
When the daylight driving lights are switch
ed on, the illumination of the instrument
cluster is switched off, however,
it is switched on in the position

when it is dark
and the low beam shines with full br
ightness (100% of the performance).
On vehicles fitted with an information displa
y*, you can also activate or deactivate in
the menu the function da
ylight driving lights:
„
Setup
„
Lights & Vision (Lights & Vision)
Automatic driving lamp control*Switching on automatic driving lamp control*– Turn the light switch
⇒fig. 45
into position

.
Switching off automatic driving lamp control*– Turn the light switch to the position 0,
 or .
If the light switch is in the position

, the symbol illuminates when the ignition is
switched on

next to the light switch. If the low beam is activated with the light
sensor, the symbol
 illuminates additionally next to the light switch.
If the light comes on automatically, the side lights and low beam as well as licence plate light light up at the same time. If the automatic light control is switched on,
the light is regulated with the light sensor
in the rear mirror holder. If the light intensity drops below the set value, e.g when driving during the day into a tunnel, the lo
w beam and the side li
ghts as well as the
licence plate light come on automatically. If
the light intensity increases again, the
lights switch off automatically. Motorway lights If the automatic light control has been swit
ched on and the vehicle speed is over 140
km/h for at least 10 seconds, the side ligh
ts and low beam are switched on automati-
cally. If the vehicle speed is below 65 km/h for at least 2 minutes, the lights are switched off.
Fig. 45 Dash panel: Light switch
sgg.6.book Page 54 Thursday, September 24, 2009 2:32 PM

Lights and Visibility
55
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Rain lights If you switch on the windscreen wipe in th
e operation rain sensor* for longer than 10
seconds or in the operation permanent wipe (position 2 or 3)
⇒page 63 switching on
for longer than 15 seconds, the side lights
and low beam are switched on automati-
cally. The light switches off if the windscreen wipe is in operation rain sensor* for more than 4 minutes or is not switched
on in the operation permanent wipe.
WARNING
The automatic light control only operat
es as a support. Th
e driver is not
released from his responsibility to inspect the light and if necessary to switch on the light depending on the light conditions. The light sensor cannot detect for example rain or snow. For these conditions we recommend to switch on the low beam
!
Note
•
Do not affix any stickers in front of the light sensor, so that you do not impair its
function or put it out of operation.•
The same principles as for using the automa
tic light control also
apply to the light
which is switched on manually
⇒page 53.
Cornering lights*The cornering lights are used to illuminate
the curves by means of the cone of light
swiveling together with the front headlight with Xenon lights*. This function is active when the speed of the car increases to more than 10km/h. The swiveling function of the headlights ca
n be switched off / on via the menu point
Assistant
in the main menu of the Information display*
⇒page 24.
WARNING
If the cornering ligh
ts are defective, the headlights are automatically lowered to
the emergency position, which prevents a
possible dazzling of oncoming traffic.
Thus the illuminated length of the road is shortened. Drive carefully and have the car inspected immediatel
y by a specialist garage.
Coming Home FunctionThe function makes it possible to switch on the lights in the darkness for a short time after leaving the vehicle.Switching on Coming Home Function– The light switch is in the position automatic driving lamp control

and the low
beam illuminates.
– Switch off the ignition. – After opening the driver's door, the function Coming Home is switched on.– Close all the doors and the boot lid and lo
ck the vehicle. After a short time, switch
all lights off.
Depending on equipment fitted the function Coming Home switches on the following lights:•
Parking lights,
•
Low beam,
•
Entry lighting in the exterior mirrors,
•
Licence plate light.
Coming Home Function The lights go out 10 seconds after cl
osing all the doors and the boot lid.
If a door or the boot lid re
mains open, the lights go out
60 seconds after switching off
the ignition. The function Coming Home is controlled with the light sensor in the mount of the inte- rior rear mirror. If the light intensity is higher than the set value of the light sensor, the Coming Home Function is not switched on after switching off the ignition.
Note
•
If the Coming Home Function is switched
on constantly, the battery will be heavily
discharged particularly in short-haul traffic.•
The switching on of the described lights
should only be undertaken in accordance
with the legal requirements.
sgg.6.book Page 55 Thursday, September 24, 2009 2:32 PM

Lights and Visibility
56•
You can change the illumination period
for the Coming Home Function by means
of the information display*.Leaving Home FunctionThis function makes it possible to switch
on the lights when approaching the vehicle.
Switching on Leaving Home Function– Unlock the vehicle with the radio remote control - the lights come on. Depending on equipment fitted
the function Leaving Home switches on the following
lights:•
Parking lights,
•
Low beam,
•
Entry lighting in the exterior mirrors,
•
Licence plate light.
Leaving Home Function The function Leaving Home is
controlled with the light sensor in the mount of the inte-
rior rear mirror. If the light intensity is higher than the set value of the light sensor, the Leaving Home Function is not switched on
after unlocking the vehicle with the radio
remote control. After unlocking the vehicle with the radio remote control, the lights come on for 10 seconds. The Leaving Home Function is also
switched off after the ignition is switched
on and after locking the vehicle. If no door is opened within 30 seconds, the lights go out and the vehicle is locked auto- matically.
Note
•
If the Leaving Home Function is switched
on constantly, the batt
ery will be heavily
discharged particularly
in short-haul traffic.
•
The switching on of the described lights
should only be undertaken in accordance
with the legal requirements.
•
You can change the illumination period
for the Leaving Home Function by means
of the information display*.Tourist light*Xenon headlight This mode makes it possible to drive in countries with opposing traffic system, driving on the left/right, without dazzling the oncoming vehicles. When the mode “tourist light” is active, the side to side swivel of the headlights is deactivated. The mode “tourist light” is activated / deactivated via the information display* in the menu:„
SETUP (Settings)
„
Tra v e l m o d e„
Off
„
On
Halogen headlight When using Halogen headlights, it is necessary to stick a sticker over a certain part of the headlights in order to prevent the dazzling of oncoming traffic. You can purchase headlight stickers from the range of the Škoda original accessories.Fog lights*

Fig. 46 Dash panel: Light switch
sgg.6.book Page 56 Thursday, September 24, 2009 2:32 PM

Lights and Visibility
57
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Switching on the fog lights– First of all turn the light switch into position
 or  ⇒page 56, fig. 46
.
– Pull the light switch into position . The rear fog light warning light
 ⇒page 29 lights up in the instrument cluster when
the fog light is switched off.Fog lights with the function “Corner”* The fog lights with the function “Corner” improve the illumination of areas close to the vehicle when turning, parking etc.The fog lights with the function “Corner” ar
e regulated according to the steering angle
or after switching on the turn signal light
8) in the following circumstances:
•
the vehicle is stationary and the engine
is running or it moves with a speed of
maximum 40 km/h;•
the daylight driving lights are not switched on;
•
the low beam is switched on or th
e light switch is
in the position

and the
intensity of the ambient light causes the low beam to be switched on;•
the fog lights are not switched on;
•
no reverse gear is engaged.Note
If you engage the reverse gear during the
active function “Corne
r”, both fog lights
illuminate.Rear fog light

Switching on the rear fog light– First of all turn the light switch into position
 or  ⇒page 56, fig. 46
.
– Pull the switch into position .
The rear fog light warning light
 ⇒page 29 lights up in the instrument cluster when
the fog light is switched off. Only the rear fog light of the trailer lights
up automatically when you are towing a trailer
using a factory-fitted towing device
which is fitted with the rear fog light.
The rear fog light is located in the rear light array on the driver's side.
Caution
The rear fog light should only be switched on
if visibility is partic
ularly poor (conform
with any varying legal provisions) to avoi
d dazzling vehicles behind your vehicle.
Instrument lighting*

You can adjust the brightness of the instrument lighting.Instrument lighting– Switch on the light. – Turn the control dial
⇒fig. 47
to the desired intensity of the instrument lighting.
For the information display*
⇒page 24 the intensity of the lighting is automatically
set. It is only possible to adjust the instrume
nt lighting with the co
ntrol dial if the light
intensity drops below the set value of the light sensor.
8)If both switch on versions are conflicting, for ex
ample if the steering wheel is turned to the left
and the right turn signal light is switched on, the turn signal light has the higher priority.
A1
A2
Fig. 47 Dash panel:
Instrument lighting
sgg.6.book Page 57 Thursday, September 24, 2009 2:32 PM