The brief instruction
12Seat belt height adjuster– Move the height adjuster in the desired direction up or down
⇒fig. 4
.
– Then pull firmly on the belt to ensure that
the seat belt height
adjuster has correctly
locked in place.
Further information
⇒page 143, “Seat belt height adjuster”.
WARNING
Adjust the height of the belt in such a way that the shoulder part of the belt is positioned approximately across the middle of your shoulder - on no account across your neck!Adjusting the front seats
Adjusting a seat in a forward/back direction Adjusting height of seat Adjust the angle of the seat backrest Adjusting lumbar support*Further information
⇒page 69, “Adjusting the front seats”.
WARNING
Only adjust the driver seat when the ve
hicle is stationary - risk of injury!
Electric exterior mirror adjustment*Further information
⇒page 67, “Exterior mirror”.
Fig. 4 Front seat: Seat belt height adjusterFig. 5 Controls at seat
Heating of the external mirror*
Adjusting left and right exterior mirrors simultaneously
Adjusting the right-hand exterior mirror
Switching off operating control
A1A2A3A4
Fig. 6 Inner part of door: Rotary knob
sgg.6.book Page 12 Thursday, September 24, 2009 2:32 PM
Seats and Stowage
70 Adjusting lumbar support*– Pull on the lever until you have set th
e most comfortable curvature of the seat
upholstery in the area of your spine.
The driver's seat should be adjusted in such a way that the pedals can be fully pressed to the floor with slightly bent legs. The seat backrest on the driver's seat should
be adjusted in such a way that the upper
point of the steering wheel can be easi
ly reached with slightly bent arms.
WARNING
•
Only adjust the driver seat when the vehicle is stationary - risk of injury!
•
Take care when adjusting the seat! Adjusting the seat without care can lead
to bruises or injuries.•
The seat backrests must not be angled too far back when driving otherwise
this will affect proper operation of the se
at belts and of the airbag system - risk
of injury!Adjusting front seats electrically*Adjusting seatsFig. 63 Side view: Controls for adju
sting the seat / seat setting switch
Adopt the correct seated position before setting
⇒page 69.
Adjusting a seat in a forward/back direction– Press the switch
⇒fig. 63
forwards or backwards
⇒fig. 63
.
Set the height of the seat cushion– Press the switch
⇒fig. 63
upwards or downwards.
Adjust the angle of the seat cushion– Press the switch at the front
⇒fig. 63
or at the back
⇒fig. 63
.
Adjusting the seat backrest– Press the switch
⇒fig. 63
in the direction of the desired setting.
Adjusting lumbar support– Press the switch front
⇒fig. 63
in order to enlarge the curvature of the lumbar
support.
– Press the switch rear in order to reduce the curvature of the lumbar support. – Press the switch top in order to adjust the curvature of the lumbar support
higher.
– Press the switch bottom in order to adjust the curvature of the lumbar support
lower.
Switch is operated in order to move
the seat up/down and forward/back, while
switch is operated in order to move the backrest forward or back.
WARNING
•
Only adjust the driver seat when the ve
hicle is stationary - risk of injury!
•
Caution when adjusting the seat! You ma
y suffer injuries or bruises as a
result of adjusting the seat without paying proper attention.•
In view of the fact that the seats can also be adjusted when the ignition is
switched off (even when ignition key withdrawn), you should never leave chil-dren unattended in the vehicle.
A4
AB
A1
ABAB
A2
A3
ACAAAAAAAA
ABAC
sgg.6.book Page 70 Thursday, September 24, 2009 2:32 PM
