2009 SKODA YETI belt

Seats and Stowage
73
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
– Move the head restraint downwards if required by pressing the locking button with
one hand in direction of arrow
⇒fig. 65
and by pressing with the other hand
the head restraint downwards.
Removing and installing a head restraint– Pull the head restraint out of the seat backrest as far as the stop. – Press the locking button in the direction of arrow
⇒page 72, fig. 65
and pull the
head restraint out.
– To re-insert the head restraint, push it down into the seat backrest far enough until
you hear the locking button engage.
The position of the front and rear outer head restraints is adjustable in height. The middle rear head restraint is adjustable in two positions. The head restraints must be adjusted to ma
tch the size of the seat occupant. Correctly
adjusted head restraints together with the
seat belts offer effective protection for the
occupants
⇒page 138, “Correct seated position”.
WARNING
•
The head restraints must be correctly
adjusted in order to offer effective
protection for the occupants in the event of an accident.•
Do not drive under any circumstance with removed head restraints - risk of
injury!•
If the rear seats are occupied, the rear head restraint must not be in the
lower position.
Middle rear head restraint*IIn certain countries national
legal provisions also require
the equipment of the rear
seat with fixing eyes for child seat using the “Top Tether” system
⇒page 162. For vehi-
cles, which are equipped with such fixing eyes, a deviating sequence for removing the middle head restraint must be observed.Removing and installing the rear middle head restraint– Pull the head restraint out of the seat backrest as far as the stop. – Press the locking button in the direction of arrow
⇒fig. 66
and pull the head
restraint out.
– To re-insert the head restraint, push it do
wn into the seat backrest far enough until
you hear the locking button engage.
WARNING
•
The head restraints must be correctly adjusted in order to offer effective
protection for the occupants in the event of an accident.•
Do not drive under any circumstance with removed head restraints - risk of
injury!•
If the rear seats are occupied, the rear
head restraint must not be in the
lower position.
A2
Fig. 66 Rear seats: middle head restraint
sgg.6.book Page 73 Thursday, September 24, 2009 2:32 PM

Seats and Stowage
74Rear seatsAdjusting seats in forward/back directionFig. 67 Releasing at the front / rearTo enlarge the luggage compartment, the ou
ter rear seats can be pushed forwards,
folded fully forwards or the seats can be removed.Moving seats in forward/back direction– Pull the lever
⇒fig. 67
up in direction of arrow or on the release loop in
direction of arrow
⇒fig. 67
and move the seat into the desired position .
Note
Please refer to the following guidelines
⇒page 139, “Correct seated position for the
occupants on the rear seats”.
Adjusting the seat backrestAdjust the angle of the seat backrest– Pull the lever
⇒fig. 68
and adjust the desired an
gle of the seat backrest.
Folding rear seats forwardsFig. 69 Fold seat forward / secure folded forward seatsFolding rear seats fully forwards and secure– Open the guide loop for the seat belt on the side of the outer seats and put the belt
tongue into the opening of the wheel housing on the respective side trim panel - safety holder.
– Remove the head restraint from the rear middle seat
⇒page 73.
– Move the rear exterior seats as far as possible to the rear
⇒page 74.
AA
A1
A2
A3
Fig. 68 Adjusting the seat backrest
sgg.6.book Page 74 Thursday, September 24, 2009 2:32 PM

Seats and Stowage
75
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
– Pull on the levers
⇒page 74, fig. 68
and fold the seat backrests of the rear exterior
seats onto the seat cushion as far as the stop.
– Fold the middle rear seat backrest forwards in the same way, then pull once more
on the lever
⇒page 74, fig. 68
and press the seat backre
st downwards until it is
heard to lock into a lower position.
– Pull the lever
⇒page 74, fig. 69
up and then fold the seat fully forwards.
– Secure the folded forward seat with the aid of the fixing belt to a guide rod of
the head restraint for the front seat
⇒page 74, fig. 69
.
WARNING
•
Immediately secure the folded forward seat
with the aid of the fixing belt to
a guide rod of the head restraint for the front seat - there is a risk of injury as soon as the vehicle starts off.•
If the seat is not in the rear end position, damage can occur to the locking
bolts if the seat is unlocked.
Caution
Make sure that the storage compartment, th
e ashtray and the cup holder in the rear
part of the centre console are closed (o
therwise these could get damaged) before
folding forward the rear middle seat.
Note
Please refer to the following guidelines
⇒page 138, “Correct seated position for the
driver”.
Removing seatsFig. 70 Unlocking the folded forward seat
/ carrying handles on the seat cushion
Unlocking and removing seats– Unlock the folded forward seat by pressin
g the seat locks in direction of arrow
⇒ fig. 70
.
– Remove the seat by way of the carrying
handles on the seat cushion and
⇒ fig. 70
.
Note
The outer seats are not replaceable alternatively.
In the rear area the left seat is marked
with the letter L and the right seat with the letter R.
Note
Please refer to the following guidelines
⇒page 139, “Correct seated position for the
occupants on the rear seats”.
AB
A1
AA
AB
sgg.6.book Page 75 Thursday, September 24, 2009 2:32 PM

Seats and Stowage
76Adjusting seats in crosswise directionMoving seats in crosswise direction– Remove the middle seat
⇒page 75.
– Fold the outer seat forwards
⇒page 74 and lock it
⇒page 75, fig. 70
.
– Move the folded forward and unlocked seat on the guide towards the middle of the
vehicle up to the stop.
– Lock the seat at the end of the guide
⇒fig. 71
.
Move seats into the initial positionLocking seats and folding back into position– If the seat is removed, first of all position it on the guide and lock the seat
⇒fig. 71
.
Check for yourself that the seat is correctly locked by pulling it up.
– Fold the seat into the horizontal position until it is heard to lock. Check for yourself
that the seat can no longer
be lifted by pulling it up.
– Push the lever
⇒fig. 72
and fold the backrest back in
to position. Check for yourself
that the seat backrest is engaged.
– Take the belt tongue out of the safety holder.– Close the guide loop of the seat belt on the side of the outer seats until it is heard
to lock.
WARNING
•
The belt locks and the belts must be in their original position after folding
back the seat cushions and the seat backrests - they must be ready to use.•
The seat backrests must be securely interlocked in position so that no
objects in the luggage compartment can
slide into the passenger compartment
if there is sudden braking - risk of injury!•
When folding the seat backrest always
make sure that it has safely locked
into position, this is confirmed by the position and a visible marking on the cover of the lever.
Note
The seat belts of the outer seats must always be guided through the guide loops next to the head restraints. Otherwise the seat belts can slip behind the seat.Folding table on the middle seat backrest*
Fig. 71 Locking the seatFig. 72 Folding the seat backrest back into position
Fig. 73 Rear seats: Armrest
sgg.6.book Page 76 Thursday, September 24, 2009 2:32 PM

Seats and Stowage
77
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
– The middle seat backrest can be folded
⇒page 74, “Folding rear seats forwards”
forwards and used as armres
t or table with cup holder
⇒page 76, fig. 73
.
– You can place two cups or beverage cans into the recesses.
Note
If the middle rear seat backrest should be
folded forward for lengthy periods, then
make sure that the belt locks are not located below it - this can result in permanent damage to the upholstery.Seat heating of the front seats*You can electrically heat the seat cushions and the seat backrests of the front seats.Front seats– You can switch on and regulate the seat heating of the driver or front passenger
seat by pressing the surface of the regulator at the point at which the symbol is located
 ⇒fig. 74
.
– With one press, you can switch the heating to highest intensity which is indicated
by the lighting up of the three warning lights in the switch.
– With repeated pressing of the switch, the intensity of the heating is down-regulated
up to the switch-off. The intensity of the heating is indicated by the number of illu- minated warning lights in the switch.
WARNING
If, as an occupant, you have a subdued pain and/or temperature sensitivity, e.g. through medication, paralysis or because of chronic illness (e.g. diabetes), we recommend not to use the seat heating.
This can lead to burns on the back, the
posterior and the legs which
are difficult to heal. If the seat heating is used, we
recommend to make regular breaks in your journey when driving long distances, so that in specific cases as
mentioned above the body can recuperate
from the stress of the journey. Please consult your doctor, who can evaluate your specific condition.
Caution
•
You should not kneel on the seats or otherwise apply pressure at specific points in
order to avoid damaging the heating elements of the seat heaters.•
Do not use the seat heating if the seats ar
e not occupied by persons or if objects
are fastened or stored on them, for example a child seat, a bag etc. A fault of the heating elements in the seat heating can occur.•
Do not clean the seats moist
⇒page 197.
Note
•
The seat heating should only be switched on when the engine is running. This has
a significant effect of savi
ng on the battery capacity.
•
If the on-board voltage drops, the seat heating is switched off automatically, in
order to provide sufficient electrical energy for the engine control.PedalsConcerning a secure depressing of the peda
l, you should use only footmats from the
Škoda genuine accessories. Operation of the pedals must not be hindered!
WARNING
•
Greater pedal distances may be needed when there is a fault in the brake
system.
Fig. 74 Dash panel: Regulator for front seat heating
sgg.6.book Page 77 Thursday, September 24, 2009 2:32 PM

Seats and Stowage
82 Pack static separation net– Press the red button of the joint - so that it releases. – Put the separation net folded together in the bag and close it. – Attach the bag with the aid of the plastic carabines to the eyes on the left and right
luggage compartment trim panel.
Installing and removing the static separation net behind the rear seats with variable loading floor*
⇒page 82 is carried out analogously as
behind the rear seats without
variable loading floor. Use the lower fixing ey
es on the carrier rails in order to attach
the carabines. The opening
⇒page 81, fig. 80
in the static separation net is designed to feed
through the three-point seat belt
⇒page 144.
Variable loading floor*Remove variable loading floorFig. 81 Luggage compartment: fold up variable
loading floor / remove variable loading floor
The variable loading floor makes it easier to handle bulky goods and creates an even luggage compartment floor when the rear seat backrests are folded forward. The maximum permissable surface load of the variable loading floor is 75 kg.
Remove variable loading floor– You can fold together the loading floor
by moving in direction of arrow
⇒ fig. 81
.
– Raise the floor in direction of arrow
⇒fig. 81
.
– Pull on both sides of the locking levers in direction of arrow
⇒fig. 81
.
– Pull the loading floor up and out in direction of arrow . – The installation of the variable loading floor is carried out in the reverse order.Secure the variable loading floor in the raised position– Fold up the hooks on the fastening strip in direction of arrow
⇒page 79, fig. 77
.
– Fold up the variable loading floor behind
the seat backrests of the rear seats.
– Fold down the hooks in direction
of arrow as far as the stop
⇒page 79, fig. 77
.
– Support the variable loading floor on the hooks folded downwards.
WARNING
Pay attention when installing that the ca
rrier rails and the variable loading floor
are correctly fixed, otherwis
e the occupants are at risk.
Note
If the variable loading floor* is installed, no flexible storage compartment can be installed.
AA
AD
A1
A2
A3
A4
A1
A3
sgg.6.book Page 82 Thursday, September 24, 2009 2:32 PM

Seats and Stowage
93
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Removing– Take hold of the flexible storage
compartment at both upper corners.
– Press the upper corners to the inside
and release the storage compartment by
pulling upwards.
– Remove by pulling towards you.Installing– Insert both ends of the flexible storage
compartment into the openings of the right
side trim panel of the luggage compartment and push it downwards until it locks.
Clothes hooksThe clothes hooks are located on the middle
pillar and on the handle of the headliner
above each of the rear doors.
WARNING
•
Ensure that any clothes hanging from the hooks do not impair your vision to
the rear.•
Use the hooks for hanging only light item
s of clothing and ensure that there
are no heavy or sharp-edge
d objects in the pockets.
•
The maximum permissable load of the hooks is 2 kg.
•
Do not use clothes hangers for hanging up items of clothing otherwise this
will interfere with the protection offered by the head airbag*.
Removeable through-loading bag*The removeable through-loading bag
is solely used for transporting
skis.The removeable through-loading bag is foreseen for two pairs of skis. The total weight of the skis which are transported must not exceed 10 kg.Loading– Open a rear side door of the vehicle. – Fold the backrest of the middle seat forwards
⇒page 74.
– Place the empty removeable through-loading bag in the gap between the front and
rear seats in such a way that the end of
the bag with the zip lies in the luggage
compartment.
– Open the boot lid.– Push the skis into the removeable through-loading bag from the luggage compart-
ment
⇒
.
– Close the removeable through-loading bag with the zip.Securing– Pull the securing belt with both lock to
ngues out of the pocket of the removeable
through-loading bag.
– Insert the lock tongues in the belt locks
of the rear middle seat belt , first of
all on the one side and then on the other side
⇒fig. 105
.
Fig. 105 Securing the removeable through-loading bag
AA
AC
sgg.6.book Page 93 Thursday, September 24, 2009 2:32 PM

Seats and Stowage
94– Place the securing belt in the middle of
the skis between the heel and the tip of the
bindings and pull the secu
ring belt tight at the free end of the belt .
Stowing– Carefully fold the empty (dry) removeable through-loading bag together, place it in
the luggage compartment and secure it to prevent it slipping.
WARNING
•
After placing the skis into the remove
able through-loading bag, you must
secure it with the securing belt .•
The securing belt must hold the skis tight.
•
Ensure that the securing belt for skis
grasps the middle between the tip and
the heel element of the binding (see al
so imprint on the removeable through-
loading bag).
Note
•
You must put the skis and the sticks in
the removeable through-loading bag with
the tips facing the rear.•
If there are skis with different lengths in the removeable through-loading bag,
ensure that the bindings are always positioned at the same height.•
The removeable through-loading bag must never be folded together or stowed
when moist.
AB
AA
sgg.6.book Page 94 Thursday, September 24, 2009 2:32 PM