2009 SKODA YETI warning light

Inspecting and replenishing
207
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
For the sake of the environment
•
You must on no account pour oil into
the ground or into the sewage system.
•
In view of the problems involved in prop
erly disposing of old oil, the necessary
special tools and the knowledge required for such work, we recommend that you have the oil and oil filter change carried out
by an authorised Škoda Service Partner.
Note
After your skin has come in contact with th
e oil, you must thoroughly wash your skin.
Cooling systemCoolant The job of the coolant is to cool the engine.The cooling system does not require any maintenance under normal operating condi- tions. The coolant consists of water with a
concentration of coolant additive of 40 %.
This mixture not only provides
antifreeze protection down to -25°C but also protects
the cooling and heating system from corrosion.
It also prevents the formation of scale
and significantly increases the boiling point of the coolant. You must therefore not reduce the concentration of antifreeze agent in the coolant by adding water, also not during the summer mo
nths or in countries with a warm climate.
The concentration of coolant additive in the coolant must be at least 40%. You can increase the amount of antifreeze in the coolant if a higher concentration of antifreeze is necessary for climatic reasons
but only up to 60% (antifreeze protection
down to approx. -40°C). The antifreeze prot
ection tails off above that concentration.
Vehicles exported to countries with a cold
climate (e.g. Sweden, Norway, Finland) are
already factory-filled with a coolant which offers antifreeze protection down to about -35°C. In these countries the concentration of
coolant additive should be at least 50 %.
Coolant The cooling system is factor
y-filled with coolant (purple
in colour), which complies
with the specification TL-VW 774 G.
We recommend that you use the same cool
ant additive - G12 PLUS-PLUS (purple in
colour) for topping up the system. Please contact an authorised Škoda Serv
ice Partner if you have any questions
regarding the coolant or if you wish
to fill up with a different coolant.
An authorised Škoda Service Partner can also supply you with the correct coolant addi- tives.
Caution
•
Other coolant additives may cause operational problems which, in particular,
involves significantly reduci
ng the anticorrosion effect.
•
Any faults or problems resulting from corrosion may cause a loss of coolant
and, as a consequenc
e of this, result in
major engine damage.
Inspecting the coolant levelThe coolant expansion bottle is located in the engine compartment on the right. – Switch the engine off. – Open the bonnet
⇒page 203.
– Check the level of coolant in the coolant expansion bottle
⇒fig. 173
. When the
engine is cold, the coolant level must
lie between the and markings. When
the engine is warm, the level may also lie slightly above the hatched part.
If the coolant level in the reservoir is too low, this is indicated by the warning light in the instrument cluster
⇒page 34, “Coolant temperature/ Coolant quantity
”. We
Fig. 173 Engine compartment: Coolant expansion bottle
Aa
Ab
sgg.6.book Page 207 Thursday, September 24, 2009 2:32 PM

Inspecting and replenishing
209
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Radiator fan The radiator fan may switch on suddenly.The radiator fan is driven by an electric
motor and controlled according to the coolant
temperature. The radiator fan may continue running for up
to 10 minutes after the engine has been
switched off - even if the igni
tion is also off. It may also
switch on suddenly after a
certain time, if•
the coolant temperature has risen beca
use of an accumulation of heat or
•
the warm engine compartment is heated
up additionally by strong sunlight.
WARNING
You must therefore be aware when workin
g in the engine compartment that the
fan may switch on suddenly - risk of injury!Brake fluidInspecting the brake fluid levelThe brake fluid reservoir is lo
cated on the left of the engine compartment. The brake
fluid reservoir on right-hand steering models is positioned on the other side of the engine compartment. – Switch the engine off.
– Open the bonnet
⇒page 203.
– Inspect the brake fluid level in the reservoir
⇒fig. 174
. The level must be between
the “MIN” and “MAX” markings.
A slight drop in the fluid level results when driving due to normal wear-and-tear and automatic adjustment of the brak
e pads, and is perfectly normal.
There may be an indication of a leak in the brake system, however, if the fluid level drops significantly within a short time or if it drops below the “MIN” marking. If the brake fluid level is too low, this
is indicated by the warning light
⇒page 37, “Brake
system
” lighting up in the instru
ment cluster. In this case
stop immediately and do
not drive any further! Obtain
professional assistance.
WARNING
•
Read and observe the warning notes
⇒page 204, “Working in the engine
compartment” before working
in the engine compartment.
•
If the fluid level has dropped below
the MIN marking, do not drive any
further - risk of accident! Obtain professional assistance.Replacing brake fluidBrake fluid absorbs moisture. This causes
the fluid to absorb moisture from the
surrounding air over a period of time. Exce
ssive water in the brake fluid may be the
cause of corrosion in the brake system. The water content also lowers the boiling point of the brake fluid.
This is why brake fluid must be replaced every two years.
One may only use new genuine brake fluid from Škoda Auto. The specification for the brake fluid is “FMVSS 116 DOT 4”. We recommend that you have th
e brake fluid re
placed by an
authorised Škoda
Service Partner
as part of an Inspection Service.
WARNING
Using old brake fluid can result in severe stress on the brakes because of the formation of vapour bubbl
es in the brake system. This greatly impairs the
braking efficiency an
d thus also the safety of your vehicle.
Fig. 174 Engine compartment: Brake fluid reservoir
sgg.6.book Page 209 Thursday, September 24, 2009 2:32 PM

Inspecting and replenishing
211
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
cable (-) on the battery. If you wish to replace a bulb it is sufficient to switch off the appropriate light.•
Never charge a frozen or thawed battery - risk of explosion and caustic
burns! Replace a frozen battery.•
Never use a battery which is damaged
- risk of explosion! Immediately
replace a damaged battery.
Caution
•
You must only disconnect the battery if th
e ignition is switched off, otherwise the
electrical system (electronic components
) of the vehicle may be damaged. When
disconnecting the battery from the electrical system of the vehicle, first disconnect the negative terminal (-) of the battery. Th
en disconnect the positive terminal (+).
•
When reconnecting the battery, first connect the positive terminal (+) and only
then the negative terminal (-) of the batt
ery. You must on no account connect the
cables wrongly - risk of a cable fire.•
Ensure that battery acid does not come
into contact with th
e vehicle body other-
wise damage could occur to the paintwork.•
Do not place the battery in
direct daylight in order to protect the battery housing
from the effects of ultra-violet light.
For the sake of the environment
A removed battery is a special type of waste which is harmful to the environment - contact your specialist garage re
garding disposing of the battery.
Note
Please also refer to the guidelines
⇒page 213, also after connecting the battery.
Battery with a two-tone indicatorAn indicator for the electrolyte level, the so-called magic eye
⇒fig. 176
, is located on
the top of the battery. The indicator changes its colour in line with the electrolyte level in the battery. Air bubbles can influence the colour of the in
dicator. For this reason carefully knock on
the indicator before carrying out the check.•
Black colour - electrolyte level is correct.
•
Colourless or light yellow colour - electrolyte level too low, the battery must be
replaced. Batteries, which are more than 5 years old, must be replaced. We recommend you have the battery checked or repl
aced by a specialist garage.
Caution
If the vehicle has not been driven for more th
an 3 to 4 weeks, the battery will discharge
because certain electrical co
mponents consume electricity (e.g. control units) also in
idle state. You can prevent the discharging of
the battery by disconnecting the negative
terminal or charging the battery constantly
with a very low charging current. Please
also refer to the notes when working on the battery
⇒page 210.
Note
•
Batteries with two-tone indicator, which
are mounted as of factory, are marked
with a code which always begins with
5K0
. The exact marking can be e.g.
5K0 915 105 D
.
WARNING (continued)
Fig. 176 The battery: Show
sgg.6.book Page 211 Thursday, September 24, 2009 2:32 PM

Inspecting and replenishing
214
Windshield washer systemThe windshield washer reservoir contains the cleaning fluid for the windscreen or rear window and for the headlamp
cleaning system*. The reserv
oir is located at the front
right of the engine compartment
⇒fig. 177
.
The
filling level
of the container is 3 litres, 5.5 li
tres on vehicles which also have a
headlight washing system. Clear water is not sufficient to intensively clean the windscreen and headlights. We therefore recommend using clean washing water together with the screen cleaner from Škoda genuine accessories (in winter
additionally with antifreeze) which is
capable of removing stubborn dirt. Follow
the instructions for use on the packaging
when using screen cleaning products. You should always add antifreeze to the cleani
ng water in winter even
if your vehicle is
fitted with heated wind
screen washer nozzles*.
It is also possible in exceptional cases to use methylated spirits when no screen cleaner with antifreeze is available. The concentratio
n of methylated spirits must not be more
than 15 %. Please note, however, that the antifreeze protection at this concentration is only adequate down to -5°C.
WARNING
Read and observe the warning notes
⇒page 204, “Working in the engine
compartment” before working in the engine compartment.
Caution
•
On no account should you add radiator an
tifreeze or other additives to the wind-
screen washer fluid.•
If the vehicle is fitted with headlight clea
ning system, you should only add cleaning
products which do not attack the polycarbonate coating of the headlights to the wind- screen washer fluid. Please contact your specialist garage, who will tell you which cleaning agent you can use.
Fig. 177 Engine compartment: Wind- shield washer fluid reservoir
sgg.6.book Page 214 Thursday, September 24, 2009 2:32 PM

Wheels and Tyres
218
means, for example, that the tyre was ma
nufactured in the 45th week of the year 2009.
Any
spare wheel
which differs from the tyres fitted to the vehicle (e.g. winter tyres or
low-profile tyres) should only be used for a short time in the event of a puncture and when adopting an appropriately cautious styl
e of driving. It should be replaced as
quickly as possible by a normal wheel.
WARNING
•
Only use those tyres or wheel rims
which have been approved for your
model of Škoda Auto vehicle. Failure to observe this instruction will adversely affect the road safety of your vehicle - risk of accident! Approval and licencing of your vehicle on public roads ma
y also become vo
id as a result.
•
You must on no account drive at a high
er speed than is permissible for your
tyres - risk of an accident resulting from tyre damage and loss of control over your vehicle.•
Tyres which are 6 years old or more should only be fitted in exceptional
cases and when adopting an approp
riately cautious style of driving.
•
Never fit tyres which have already b
een used without having adequate
knowledge of their previous history. Tyre
s age even if they have not been used
at all or only very little. A spare tyre must only be used in exceptional cases and only then when adopting an appropriately cautious style of driving.•
Do not, where possible, replace individu
al tyres but at least replace them on
both wheels of a given axle at the same time. Always fit the tyres with the deeper tread depth to the front wheels.
For the sake of the environment
Old tyres must be disposed of in conf
ormity with the appropriate regulations.
Note
It is not normally possible to
fit wheels from other models of cars for technical reasons.
This may also apply
in certain circumstances to the wheels of the same type of
vehicle.
Wheel boltsWheels and
wheel bolts
are matched to each other in terms of design. Each time you
fit other wheels - e.g. light alloy wheels or wheels with winter tyres - you must therefore also use the matching wheel bolts of the corr
ect length and shape of spherical cap. This
is essential to ensure that the wheels are tightly fitted and that the brake system oper- ates properly. If you retrofit
wheel trims
(or have this done), please
also ensure that an adequate
flow of air remains assured for cooling the brake system. The authorised Škoda Service Partners are instructed in the technical possibilities which exist regarding converting or retrofitting tyres, wheels and wheel trims.
WARNING
•
In case of incorrect treatment of the
wheel bolts, the wheel can loosen when
the car is moving - risk of accident!•
The wheel bolts must be clean and must
turn easily. However, they must
never be treated with grease or oil.•
If the wheel bolts are tightened to a
too low tightening torque, the rim can
lossen when the car is moving - risk of accident! A tightening torque which is too high can damage the bolts and threads and this can result in permanent deformation of the contact surfaces on the rims.
Caution
The prescribed tightening torque of the wheel bolts for steel and light alloy wheels is 120 Nm.Winter tyresThe handling of your vehicle will be signi
ficantly improved when driving on wintry
roads if you fit winter tyres. Summer tyres do not offer the same grip on ice, snow and at temperatures below 7 °C because of thei
r construction (width, rubber blend, tread
pattern). This particularly applies
to vehicles which
are equipped with
low-profile
tyres
or high-speed tyres
(code index H or V on wall of tyre).
sgg.6.book Page 218 Thursday, September 24, 2009 2:32 PM

Breakdown assistance
225
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Changing a wheelPreliminary workThe following steps should be carried ou
t before actually changing the wheel.
– If it is necessary to change a wheel, park
the vehicle as far aw
ay as possible from
the traffic flow. The place you choose should be
level
.
–Have
all the occupants get out.
While changing a wheel, the occupants of the
vehicle should not stand on the ro
ad (e.g. behind a crash barrier).
– Apply the
handbrake
firmly.
–Engage
1st gear
or if your vehicle is fitted with
an automatic gearbox, position the
selector lever into position P
.
– If a trailer is coupled, uncouple it. –Take the
vehicle tool kit
⇒page 223 and the
spare wheel*
⇒page 224 out of the
luggage compartment.
WARNING
•
If you find yourself in flowing traffic switch on the hazard warning lights
system and place the warning triangle on
the side of the road at the prescribed
distance from your vehicle while observing all national legal provisions. In this way you are protecting not only yourself but also other road users.•
Never start the engine with the vehicle si
tting on the raised
jack - danger of
suffering injury.
Caution
If you have to change a wheel on a slope first block the opposite wheel with a stone or similar object in order to secure the
vehicle from unexpectedly rolling away.
Note
Comply with the national legal regulations.
Changing a wheelAlways change a wheel on a level surface as far as possible. – Take off the full wheel trim*
⇒page 226 or the caps
⇒page 226.
– In the case of light alloy wheels remove the wheel trim cap
⇒page 227.
– First of all slacken the safety wheel bolt * and afterwards the other wheel bolts
⇒ page 227.
– Jack up the vehicle until the wheel to
be changed is clear of the ground
⇒ page 227.
– Unscrew the wheel bolts and place them
on a clean surface (cloth, paper etc.).
– Take off the wheel. – Fit on the spare wheel and tighten the wheel bolts slightly.– Lower the car. – Tighten the wheel bolts firmly, alternatel
y and diagonally using the wheel wrench
(crosswise) and last the safety wheel bolt*
⇒page 227.
Note
•
All bolts must be clean and must turn easily.
•
You must never grease or oil the wheel bolts!
•
When fitting on unidirectiona
l tyres, ensure that the tyres rotate in the correct
direction
⇒page 215.
Subsequent stepsAfter changing the wheel, you mu
st perform the following steps.
– Stow the vehicle tool kit in the space provided.– Stow the replaced wheel in the luggage compartment. –
Check
the
tyre pressure
on the spare wheel just mounted as soon as possible.
sgg.6.book Page 225 Thursday, September 24, 2009 2:32 PM

Breakdown assistance
226
– Have the
tightening torque
of the wheel bolts
checked
with a torque wrench as
soon as possible. Steel and light alloy wh
eels must be tightened to a tightening
torque of
120 Nm
.
– Change the damaged wheel or consult a specialist garage about possibilities for
getting repairs done.
WARNING
It is necessary to observe the guidelines given on
⇒page 217 if the vehicle is
subsequently fitted with tyres which are different to those it was fitted with at the works.
Note
•
If you find, when changing the wheel, that
the wheel bolts are corroded and diffi-
cult to turn, the bolts must be replaced
before checking the tightening torque.
•
Drive cautiously and only at a moderate speed to a workshop where the tightening
torque can be checked.Full wheel trim*Pulling off– Hook the clamp found in the vehicle tool
kit into the reinforced edge of the full
wheel trim.
– Push the wheel key through the clamp, support the wheel key at the tyre and pull
off the wheel trim.
Installing– First press the full wheel trim onto the wheel at the valve opening provided. Then
press the full wheel trim into the wheel in
such a way that its entire circumference
locks correctly in place.
Caution
•
Use the pressure of your hand, do not knock on the full wheel trim! Heavy knocks
mainly on the points where the full wheel trim has not been inserted into the wheel, can result in damage to the guide and centering elements of the full wheel trim.•
Check for yourself that the safety wheel bolt
is located in the hole in the area of the
valve before fitting the full wheel trim onto a
steel wheel which is attached with a safety
wheel bolt
⇒page 228.
Wheel bolts with caps*Pulling off– Push the plastic clip sufficie
ntly far onto the cap until th
e inner catches of the clip
are positioned at the collar
of the cap and detach the cap.
Installing– Push the caps fully onto the wheel bolts. The caps are located in the well of the luggage compartment.
Fig. 184 Removing the cap
sgg.6.book Page 226 Thursday, September 24, 2009 2:32 PM

Breakdown assistance
227
Using the system
Safety
Driving Tips
General Maintenance
Breakdown assistance
Technical Data
Wheel trim caps*Pulling off– Carefully remove the wheel tr
im cap using the wire clamp
⇒fig. 185
.
Slackening and tightening wheel bolts Slacken the wheel bolts befo
re jacking up the vehicle.
Slackening wheel bolts– Push the wheel wrench* fully onto the wheel bolt
16).
– Grasp the end of the wrench* and turn the bolt about
one
turn to the left
⇒ fig. 186
.
Tightening wheel bolts– Push the wheel wrench* fully onto the wheel bolt
16).
– Grasp the end of the wrench* and turn the bolt to the right until it is tight.
WARNING
Slacken the wheel bolts only a little (about one turn) as long as the vehicle has not yet been jacked up - risk of an accident!
Note
Apply pressure carefully with your
foot
to the end of the wrench* if it proves difficult
to slacken the bolts. Hold tight on the vehicl
e when doing this and ensure that you have
a steady position.Raise vehicle You have to raise the vehicle with the
lifting jack* in order to be able to
take off the wheel.Position the lifting jack* by selecting the ja
cking point which is closest to the wheel to
be removed
⇒fig. 187
. The jacking point is located directly below the marking on the
plastic cover of the lower sill. – Position the lifting jack* be
low the jacking point and move it up until its claw is
positioned directly below the
vertical web of the lower sill.
16)Use the appropriate adapter for slackening and tightening the safety wheel bolts
⇒page 228.
Fig. 185 Pulling off wheel trim cap on light alloy wheelsFig. 186 Changing a wheel: Slackening wheel bolts
Fig. 187 Changing a wheel: Jacking points for positioning lifting jack
sgg.6.book Page 227 Thursday, September 24, 2009 2:32 PM