2009 SATURN VUE light

Fuel Gage
When the ignition is on, the fuel
gage indicates how much fuel is
left in the tank.
When the indicator nears empty,
the low fuel light comes on. There is
still a little fuel left, but the fuel tank
should be relled soon. SeeLow
Fuel Warning Light on page 3-41
for more information.
An arrow on the fuel gage indicates
the side of the vehicle the fuel
door is on.Here are four things that some
owners ask about. None of these
means the fuel gage is not working
properly:
At the service station, the fuel
pump shuts off before the
gage reads full.
It takes a little more or less fuel
to ll up than the gage indicated.
For example, the gage may have
indicated the tank was half full,
but it actually took a little more or
less than half the tank’s capacity
to ll the tank.
The gage moves a little while
turning a corner or speeding up.
The gage takes a few seconds to
stabilize after the ignition is turned
on, but it goes back to empty
when the ignition is turned off.
For fuel tank capacity, see
Capacities and Specifications
on page 5-86.
Low Fuel Warning Light
The low fuel warning light, below
the fuel gage, comes on briey when
the engine is started.
This light also comes on when the
fuel tank is low on fuel. When fuel is
added, the light should go off. If it
does not, have the vehicle serviced. United StatesCanada
Instrument Panel 3-41
ProCarManuals.com

If the DIC display does not show a
heading, for example, N for North,
or the heading does not change after
making turns, there may be a strong
magnetic eld interfering with the
compass. Such interference may
be caused by a magnetic CB or cell
phone antenna mount, a magnetic
emergency light, magnetic note pad
holder, or any other magnetic item.
Turn off the vehicle, move the
magnetic item, then turn on the
vehicle and calibrate the compass.
To calibrate the compass, use the
following procedure:
Compass Calibration Procedure
1. Before calibrating the compass,
make sure the compass is set to
the variance zone in which the
vehicle is located. See “Compass
Variance (Zone) Procedure”
earlier in this section.Do not operate any switches
such as window, sunroof, climate
controls, seats, etc. during the
calibration procedure.
2. Press the vehicle information
button until PRESS
VTO
CALIBRATE COMPASS
displays.
3. Press the set/reset button to start
the compass calibration.
4. The DIC will display
CALIBRATING COMPASS:
TURN IN CIRCLES. Drive the
vehicle in tight circles at less than
5 mph (8 km/h) to complete the
calibration. The DIC will display
COMPASS CALIBRATION
COMPLETE for a few seconds
when the calibration is complete.
The DIC display will then return to
the previous menu.
DIC Warnings and
Messages
Messages are displayed on the DIC
to notify the driver that the status
of the vehicle has changed and that
some action may be needed by
the driver to correct the condition.
Multiple messages may appear
one after another.
Some messages may not require
immediate action, but you can
press any of the DIC buttons,
or the trip odometer reset stem
on the instrument panel cluster to
acknowledge that you received the
messages and to clear them from
the display.
Some messages cannot be cleared
from the DIC display because they
are more urgent. These messages
require action before they can be
cleared. Take any messages that
appear on the display seriously
and remember that clearing the
messages will only make the
messages disappear, not correct
the problem.
Instrument Panel 3-49
ProCarManuals.com

CHECK TIRE PRESSURE
On vehicles with the Tire Pressure
Monitor System (TPMS), this
message displays when the pressure
in one or more of the vehicle’s tires
needs to be checked. This message
also displays LEFT FRONT, RIGHT
FRONT, LEFT REAR, or RIGHT
REAR to indicate which tire needs to
be checked. You can receive more
than one tire pressure message at a
time. To read the other messages
that may have been sent at the same
time, press the set/reset button. If a
tire pressure message appears on
the DIC, stop as soon as you can.
Have the tire pressures checked
and set to those shown on the Tire
Loading Information label. SeeTires
on page 5-43,Loading the Vehicle
on page 4-28, andInflation - Tire
Pressure on page 5-49. The DIC
also shows the tire pressure values.
SeeDIC Operation and Displays on
page 3-42. If the tire pressure is low,
the low tire pressure warning light
comes on. SeeTire Pressure Light
on page 3-34.
COMPASS CALIBRATION
COMPLETE
This message displays when the
compass calibration is complete.
SeeDIC Compass on page 3-47.
CRUISE CONTROL SET
TO XXX
This message displays whenever
the cruise control is set. SeeCruise
Control on page 3-9for more
information.
DRIVER DOOR OPEN
This message displays when the
driver door is not closed properly.
Close the door completely.
ENGINE HOT A/C
(Air Conditioning) OFF
This message displays when the
engine coolant becomes hotter than
the normal operating temperature.
To avoid added strain on a hotengine, the air conditioning
compressor is automatically turned
off. When the coolant temperature
returns to normal, the A/C operation
automatically resumes. You can
continue to drive your vehicle.
ENGINE OVERHEATED IDLE
ENGINE
Notice:If you drive your vehicle
while the engine is overheating,
severe engine damage may occur.
If an overheat warning appears
on the instrument panel cluster
and/or DIC, stop the vehicle as
soon as possible. Do not increase
the engine speed above normal
idling speed. SeeEngine
Overheating on page 5-25for
more information.
This message displays when the
engine coolant temperature is
too hot. Stop and allow the vehicle
to idle until it cools down.
Instrument Panel 3-51
ProCarManuals.com

ICE POSSIBLE DRIVE
WITH CARE
This message displays when the
outside air temperature is cold
enough to create icy road
conditions. Adjust your driving
accordingly.
LIFTGATE OPEN
This message displays when the
liftgate is not closed completely.
Close the liftgate completely.
SeeLiftgate on page 2-9.
OIL PRESSURE LOW STOP
ENGINE
Notice:If you drive your vehicle
while the engine oil pressure
is low, severe engine damage
may occur. If a low oil pressure
warning appears on the Driver
Information Center (DIC), stop
the vehicle as soon as possible.Do not drive the vehicle until the
cause of the low oil pressure
is corrected. SeeEngine Oil on
page 5-14for more information.
This message displays when the
vehicle’s engine oil pressure is low.
The oil pressure light also appears
on the instrument panel cluster.
SeeOil Pressure Light on page 3-37.
Stop the vehicle immediately,
as engine damage can result
from driving a vehicle with low oil
pressure. Have the vehicle serviced
by your dealer/retailer as soon as
possible when this message is
displayed.PASSENGER DOOR OPEN
This message displays when one
or more of the passenger doors
are not closed properly. Close the
doors completely.
REMOTE KEY LEARNING
ACTIVE
This message displays while
matching a Remote Keyless
Entry (RKE) transmitter to your
vehicle. See “MATCHING
TRANSMITTERS TO YOUR
VEHICLE” underRemote Keyless
Entry (RKE) System Operation on
page 2-4andDIC Operation and
Displays on page 3-42for more
information.
REMOTE KEY LEARNING
COMPLETE
This message displays while
matching a Remote Keyless Entry
(RKE) transmitter to your vehicle.
See “MATCHING TRANSMITTERS
TO YOUR VEHICLE” underRemote
Keyless Entry (RKE) System
Operation on page 2-4andDIC
Operation and Displays on
page 3-42for more information.
Instrument Panel 3-53
ProCarManuals.com

REPLACE REMOTE KEY FOB
BATTERY
This message displays if a Remote
Keyless Entry (RKE) transmitter
battery is low. The battery needs
to be replaced in the transmitter.
See “Battery Replacement” under
Remote Keyless Entry (RKE)
System Operation on page 2-4.
SERVICE A/C
(Air Conditioning) SYSTEM
This message displays when there
is a problem detected in the air
conditioning system. Have the
vehicle serviced by your dealer/
retailer.
SERVICE AIR BAG
This message displays when
there is a problem with the airbag
system. Have your vehicle serviced
by your dealer/retailer immediately.
SeeAirbag Readiness Light on
page 3-29for more information.
SERVICE BRAKE SYSTEM
This message displays along with
the brake system warning light if
there is a problem with the brake
system or when the brake uid level
is low. SeeBrake System Warning
Light on page 3-31. Have the brake
system serviced by your dealer/
retailer as soon as possible.
SERVICE POWER STEERING
If the vehicle has electric power
steering, this message displays if
a problem has been detected with
the power steering. SeeSteering
on page 4-9for more information.
SERVICE STABILITRAK
This message displays if there
has been a problem detected with
StabiliTrak
®. A warning light also
appears on the instrument panel
cluster. SeeStabiliTrak
®Indicator
Light on page 3-33. SeeStabiliTrak®
System on page 4-7for more
information.If this message turns on while you
are driving, pull off the road as soon
as possible and stop carefully. Try
resetting the system by turning the
ignition off and then back on. If this
message still stays on or turns back
on again while you are driving, your
vehicle needs service. Have the
system inspected by your dealer/
retailer as soon as possible.
SERVICE TIRE MONITORING
SYSTEM
On vehicles with the Tire Pressure
Monitor System (TPMS), this
message displays if a part on the
TPMS is not working properly.
The tire pressure light also ashes
and then remains on during the
same ignition cycle. SeeTire
Pressure Light on page 3-34.
Several conditions may cause
this message to appear. SeeTire
Pressure Monitor Operation on
page 5-53for more information.
If the warning comes on and stays
on, there may be a problem with the
TPMS. See your dealer/retailer.
3-54 Instrument Panel
ProCarManuals.com

SERVICE TRACTION
CONTROL
This message displays when the
Traction Control System (TCS) is not
functioning properly. A warning light
also appears on the instrument panel
cluster. SeeTraction Control System
(TCS) Warning Light on page 3-33
andTraction Control System (TCS)
on page 4-8for more information.
Have the TCS serviced by your
dealer/retailer as soon as possible.
SERVICE TRANSMISSION
This message displays when there
is a problem with the transmission.
See your dealer/retailer for service.
SERVICE VEHICLE SOON
This message displays when
a non-emissions related malfunction
occurs. Have the vehicle serviced
by your dealer/retailer as soon
as possible.
STABILITRAK NOT READY
If your vehicle has StabiliTrak,
this message may display and the
StabiliTrak indicator light on the
instrument panel cluster may be on
after rst driving the vehicle and
exceeding 20 mph (32 km/h) for
30 seconds. The StabiliTrak system
is not functional until the light has
turned off. SeeStabiliTrak
®System
on page 4-7for more information.
STABILITRAK OFF
If your vehicle has StabiliTrak, this
message displays when you turn off
the StabiliTrak, or when the stability
control has been automatically
disabled. To limit wheel spin and
realize the full benets of the stability
enhancement system, you should
normally leave StabiliTrak on.
However, you should turn StabiliTrak
off if your vehicle gets stuck in sand,
mud, ice, or snow and you want to
rock your vehicle to attempt to free it,or if you are driving in extreme
off-road conditions and require more
wheel spin. SeeIf Your Vehicle is
Stuck in Sand, Mud, Ice, or Snow on
page 4-27. To turn the StabiliTrak
system on or off, seeStabiliTrak
®
System on page 4-7.
TIGHTEN GAS CAP
This message may display along
with the check engine light on the
instrument panel cluster if the
vehicle’s fuel cap is not tightened
properly. SeeMalfunction Indicator
Lamp on page 3-35. Reinstall the
fuel cap fully. SeeFilling the Tank
on page 5-8. The diagnostic system
can determine if the fuel cap has
been left off or improperly installed.
A loose or missing fuel cap allows
fuel to evaporate into the
atmosphere. A few driving trips
with the cap properly installed should
turn this light and message off.
Instrument Panel 3-55
ProCarManuals.com

VERIFICATION LIGHTS ONLY:The
exterior lamps will ash when you
press the lock button on the RKE
transmitter.
VERIFICATION HORN ONLY:
The horn will sound on the second
press of the lock button on the
RKE transmitter.
VERIFICATION HORN & LIGHTS
(default):The exterior lamps will
ash when you press the lock button
on the RKE transmitter, and the horn
will sound when the lock button is
pressed again within ve seconds
of the previous command.
VERIFICATION NO CHANGE:No
change will be made to this feature.
The current setting will remain.
To select a setting, press the
set/reset button while the desired
setting is displayed on the DIC.REMOTE DOOR UNLOCK
This feature allows you to select
the type of feedback you will receive
when unlocking the vehicle with
the Remote Keyless Entry (RKE)
transmitter. You will not receive
feedback when unlocking the vehicle
with the RKE transmitter if the doors
are open. SeeRemote Keyless
Entry (RKE) System Operation on
page 2-4for more information.
Press the customization button
until PRESS
VTO SET REMOTE
DOOR UNLOCK appears on the
DIC display. Press the set/reset
button once to access the settingsfor this feature. Then press the
customization button to scroll
through the following settings:
VERIF LIGHTS OFF:The exterior
lamps will not ash when you press
the unlock button on the RKE
transmitter.
VERIF LIGHTS ON (default):
The exterior lamps will ash when
you press the unlock button on
the RKE transmitter.
VERIF NO CHANGE:No change
will be made to this feature.
The current setting will remain.
To select a setting, press the
set/reset button while the desired
setting is displayed on the DIC.
3-60 Instrument Panel
ProCarManuals.com

DELAY DOOR LOCK
This feature allows you to select
whether or not the locking of the
vehicle’s doors will be delayed.
When locking the doors with the
power door lock switch and a door
is open, this feature will delay locking
the doors until ve seconds after
the last door is closed. You will
hear three chimes to signal that the
delayed locking feature is in use.
The key must be out of the ignition
for this feature to work. You can
temporarily override delayed locking
by pressing the power door lock
switch twice or the lock button on the
RKE transmitter twice. SeeDelayed
Locking on page 2-8for more
information.Press the customization button
until PRESS
VTO SET DELAY
DOOR LOCK appears on the
DIC display. Press the set/reset
button once to access the settings
for this feature. Then press the
customization button to scroll
through the following settings:
OFF:There will be no delayed
locking of the vehicle’s doors.
ON (default):The doors will not
lock until ve seconds after the last
door is closed.
NO CHANGE:No change will be
made to this feature. The current
setting will remain.
To select a setting, press the
set/reset button while the desired
setting is displayed on the DIC.EXIT LIGHTING
This feature allows you to select the
amount of time you want the exterior
lamps to remain on when it is dark
enough outside. This happens after
the key is turned from ON/RUN to
LOCK/OFF.
Press the customization button until
PRESS
VTO SET EXIT LIGHTING
appears on the DIC display. Press
the set/reset button once to access
the settings for this feature. Then
press the customization button to
scroll through the following settings:
OFF:The exterior lamps will not
turn on.
10 SECONDS (default):The
exterior lamps will stay on for
10 seconds.
Instrument Panel 3-61
ProCarManuals.com