2009 HUMMER H3 child restraint

Some child restraints that have a top
tether are designed for use with or
without the top tether being attached.
Others require the top tether always
to be attached. In Canada, the law
requires that forward-facing child
restraints have a top tether, and that
the tether be attached. Be sure to
read and follow the instructions for
the child restraint.
If the child restraint does not have a
top tether, one can be obtained,
in kit form, for many child restraints.
Ask the child restraint manufacturer
whether or not a kit is available.Lower Anchor and Top Tether
Anchor Locations
i(Top Tether Anchor): Seating
positions with top tether anchors.
j(Lower Anchor): Seating positions
with two lower anchors.Each outboard seating position in
the rear seat has exposed metal
lower anchors in the crease between
the seatback and the seat cushion.
For H3T models, the top tether
anchor symbol is located near the
top tether anchors to assist you
in locating the top tether anchors.
Rear Seat
Seats and Restraint System 1-35

For H3T models, the top tether
anchors are located on the back
panel behind each rear seating
position. Be sure to use an anchor
located on the same side of the
vehicle as the seating position where
the child restraint will be placed.For H3 models, the top tether
anchors are located on the back of
the rear seatbacks. Be sure to use
an anchor located on the same side
of the vehicle as the seating position
where the child restraint will be
placed.
Do not secure a child restraint in a
position without a top tether anchor if
a national or local law requires that
the top tether be attached, or if the
instructions that come with the child
restraint say that the top tether must
be attached.According to accident statistics,
children and infants are safer when
properly restrained in a child restraint
system or infant restraint system
secured in a rear seating position.
SeeWhere to Put the Restraint on
page 1-32for additional information.
Securing a Child Restraint
Designed for the LATCH System
{CAUTION
If a LATCH-type child restraint is
not attached to anchors, the child
restraint will not be able to protect
the child correctly. In a crash, the
child could be seriously injured or
killed. Install a LATCH-type child
restraint properly using the
anchors, or use the vehicle’s
safety belts to secure the
restraint, following the instructions
that came with the child restraint
and the instructions in this manual. H3TH3
1-36 Seats and Restraint System

{CAUTION
Do not attach more than one child
restraint to a single anchor.
Attaching more than one child
restraint to a single anchor could
cause the anchor or attachment to
come loose or even break during
a crash. A child or others could
be injured. To reduce the risk of
serious or fatal injuries during a
crash, attach only one child
restraint per anchor.
{CAUTION
Children can be seriously injured
or strangled if a shoulder belt is
wrapped around their neck and
the safety belt continues to
tighten. Buckle any unused safety
(Continued)
CAUTION (Continued)
belts behind the child restraint so
children cannot reach them. Pull
the shoulder belt all the way out
of the retractor to set the lock, if
your vehicle has one, after the
child restraint has been installed.
Notice:Do not let the LATCH
attachments rub against the
vehicle’s safety belts. This may
damage these parts. If necessary,
move buckled safety belts to avoid
rubbing the LATCH attachments.
Do not fold the empty rear seat
with a safety belt buckled. This
could damage the safety belt or
the seat. Unbuckle and return the
safety belt to its stowed position,
before folding the seat.
H3T Models
1. If the child restraint manufacturer
recommends that the top tether
be attached, attach and tightenthe top tether to the top tether
anchor (A), if equipped. Refer to
the child restraint instructions and
the following steps:
1.1. Put the child restraint on
the seat.
1.2. Pull the seatback forward
to access the top tether
anchors (A). See60/40 Split
Bench Seat (H3) on page 1-7
or60/40 Split Bench
Seat (H3T) on page 1-9
for additional information.
Seats and Restraint System 1-37

1.3. Route the top tether
according to the child
restraint instructions and the
following instructions:
If the position you are using
does not have a headrest or
head restraint and you are
using a single tether, route
the tether over the seatback.If the position you are using
does not have a headrest or
head restraint and you are
using a dual tether, route the
tether over the seatback.If the position you are using
has a xed headrest or
head restraint and you are
using a single tether,
route the tether over the
headrest or head restraint.
1-38 Seats and Restraint System

If the position you are using
has a xed headrest or
head restraint and you are
using a dual tether,
route the tether around the
headrest or head restraint.
1.4. Attach the top tether to the
anchor (A). Make sure that
you secure the top tether to
the top tether anchor and not
to the seatback latch (B).
1.5. Push rearward on the
seatback until it locks
into its upright position.
Push and pull on the
seatback to make sure it is
secured properly.2. Attach and tighten the lower
attachments to the lower
anchors. If the child restraint
does not have lower attachments
or the desired seating position
does not have lower anchors,
secure the child restraint with the
top tether and the safety belts.
Refer to the child restraint
manufacturer instructions and the
instructions in this manual.
2.1. Find the lower anchors for
the desired seating position.
2.2. Attach and tighten the
lower attachments on
the child restraint to the
lower anchors.
3. Tighten the top tether. If the
headrest interferes with the
installation of the child restraint,
remove the headrest by
pressing the button on the
headrest post, at the top of the
seatback and lift to remove. Store
the headrest under the outboard
side of the rear seat.4. Push and pull the child restraint
in different directions to be sure
it is secure. When removing
the child restraint, reinsert
the headrest if it has been
removed from the seatback.
H3 Models
1. Attach and tighten the lower
attachments to the lower
anchors. If the child restraint
does not have lower attachments
or the desired seating position
does not have lower anchors,
secure the child restraint with
the top tether and the safety
belts. Refer to the child restraint
manufacturer instructions and
the instructions in this manual.
1.1. Find the lower anchors
for the desired seating
position.
1.2. Put the child restraint on
the seat.
1.3. Attach and tighten the
lower attachments on
the child restraint to the
lower anchors.
Seats and Restraint System 1-39

2. If the child restraint manufacturer
recommends that the top tether
be attached, attach and tighten
the top tether to the top tether
anchor, if equipped. Refer to the
child restraint instructions and the
following steps:
2.1. Find the top tether anchor.
2.2. Route, attach and tighten the
top tether according to the
child restraint instructions
and the following
instructions:
If the position you are using
does not have a headrest or
head restraint and you are
using a single tether, route
the tether over the seatback.If the position you are using
does not have a headrest or
head restraint and you are
using a dual tether, route the
tether over the seatback.
If the position you are using
has a xed headrest or
head restraint and you are
using a single tether,
route the tether over the
headrest or head restraint.If the position you are using
has a xed headrest or
head restraint and you are
using a dual tether,
route the tether around the
headrest or head restraint.
3. Push and pull the child restraint
in different directions to be sure
it is secure.
1-40 Seats and Restraint System

Securing a Child
Restraint in a Rear
Outside Seat Position
When securing a child restraint
in a rear seating position, study the
instructions that came with the
child restraint to make sure
it is compatible with this vehicle.
If the child restraint has the LATCH
system, seeLower Anchors and
Tethers for Children (LATCH) on
page 1-34for how and where to
install the child restraint using
LATCH. If a child restraint is secured
in the vehicle using a safety belt and
it uses a top tether, seeLower
Anchors and Tethers for Children
(LATCH) on page 1-34for top tether
anchor locations.Do not secure a child seat in a
position without a top tether anchor
if a national or local law requires
that the top tether be anchored, or if
the instructions that come with
the child restraint say that the top
strap must be anchored.
In Canada, the law requires that
forward-facing child restraints have
a top tether, and that the tether
be attached.
If the child restraint does not have
the LATCH system, you will be using
the safety belt to secure the child
restraint in this position. Be sure to
follow the instructions that came
with the child restraint. Secure the
child in the child restraint when
and as the instructions say.If more than one child restraint
needs to be installed in the
rear seat, be sure to readWhere to
Put the Restraint on page 1-32.
1. Put the child restraint on the seat.
2. Pick up the latch plate, and
run the lap and shoulder portions
of the vehicle’s safety belt
through or around the restraint.
The child restraint instructions
will show you how.
3. For H3T models, tilt the latch
plate to adjust the belt if needed.
Seats and Restraint System 1-41

4. Push the latch plate into the
buckle until it clicks.
Position the release button on
the buckle so that the safety belt
could be quickly unbuckled if
necessary.5. For H3 models, pull the rest of the
shoulder belt all the way out of the
retractor to set the lock.6. To tighten the belt, push down on
the child restraint, pull the
shoulder portion of the belt to
tighten the lap portion of the belt
and feed the shoulder belt back
into the retractor. When installing
a forward-facing child restraint, it
may be helpful to use your knee
to push down on the child
restraint as you tighten the belt.
1-42 Seats and Restraint System