2009 HUMMER H3 tire size

seats, safety belts, the airbag
sensing and diagnostic module,
steering wheel, instrument panel,
roof-rail airbag modules, ceiling
headliner or pillar garnish trim,
overhead console, front sensors,
side impact sensors, rollover
sensor module, or airbag wiring
can affect the operation of the
airbag system.
In addition, the vehicle has a
passenger sensing system for the
right front passenger position,
which includes sensors that are
part of the passenger seat.
The passenger sensing system
may not operate properly if the
original seat trim is replaced with
non-GM covers, upholstery or
trim, or with GM covers,
upholstery or trim designed for a
different vehicle. Any object, such
as an aftermarket seat heater or a
comfort enhancing pad or device,
installed under or on top of theseat fabric, could also interfere
with the operation of the
passenger sensing system.
This could either prevent proper
deployment of the passenger
airbag(s) or prevent the
passenger sensing system from
properly turning off the passenger
airbag(s). SeePassenger
Sensing System on page 1-54.
If you have any questions, call
Customer Assistance. The phone
numbers and addresses for
Customer Assistance are in
Step Two of the Customer
Satisfaction Procedure in this
manual. SeeCustomer
Satisfaction Procedure on
page 7-1.
If the vehicle has rollover
roof-rail airbags, seeDifferent
Size Tires and Wheels on
page 5-61for additional
important information.Q:Because I have a disability,
I have to get my vehicle
modied. How can I nd out
whether this will affect my
airbag system?
A:If you have questions, call
Customer Assistance. The phone
numbers and addresses for
Customer Assistance are in
Step Two of the Customer
Satisfaction Procedure in this
manual. SeeCustomer
Satisfaction Procedure on
page 7-1.
In addition, your dealer/retailer and
the service manual have information
about the location of the airbag
sensors, sensing and diagnostic
module and airbag wiring.
Seats and Restraint System 1-59

Combine several trips into a
single trip.
Replace the vehicle’s tires with
the same TPC Spec number
molded into the tire’s sidewall
near the size.
Follow recommended scheduled
maintenance.
Defensive Driving
Defensive driving means “always
expect the unexpected.” The
rst step in driving defensively is to
wear your safety belt — See
Safety Belts: They Are for Everyone
on page 1-11.
{CAUTION
Assume that other road users
(pedestrians, bicyclists, and other
drivers) are going to be careless
and make mistakes. Anticipate
what they might do and be ready.
In addition:
Allow enough following
distance between you and
the driver in front of you.
Focus on the task of driving.
Driver distraction can cause
collisions resulting in injury or
possible death. These simple
defensive driving techniques could
save your life.
Drunk Driving
{CAUTION
Drinking and then driving is very
dangerous. Your reexes,
perceptions, attentiveness, and
judgment can be affected by even
a small amount of alcohol. You
can have a serious — or even
fatal — collision if you drive after
drinking. Do not drink and drive or
ride with a driver who has been
drinking. Ride home in a cab; or if
you are with a group, designate a
driver who will not drink.
Death and injury associated with
drinking and driving is a global
tragedy.
Alcohol affects four things that
anyone needs to drive a vehicle:
judgment, muscular coordination,
vision, and attentiveness.
4-2 Driving Your Vehicle

The Tire and Loading
Information label shows the
number of occupant seating
positions (A), and the maximum
vehicle capacity weight (B) in
kilograms and pounds.
The Tire and Loading Information
label also shows the size of the
vehicle’s original equipment
tires (C) and the recommended
cold tire ination pressures (D).
For more information on tires and
ination seeTires on page 5-44
andInflation - Tire Pressure on
page 5-51.
There is also important
information on the
Certication/Tire label. It tells
Gross Vehicle Weight Rating
(GVWR) and the Gross
Axle Weight Rating (GAWR)
for the front and rear axles. See
“Certication/Tire Label” later
in this section.Steps for Determining Correct
Load Limit
1.
Locate the statement “The
combined weight of occupants
and cargo should never
exceed XXX kg or XXX lbs” on
your vehicle’s placard.
2.Determine the combined
weight of the driver and
passengers that will be riding
in your vehicle.
3.Subtract the combined weight
of the driver and passengers
from XXX kg or XXX lbs.
4.The resulting gure equals the
available amount of cargo and
luggage load capacity. For
example, if the “XXX” amount
equals 1400 lbs and there will
be ve 150 lb passengers in
your vehicle, the amount
of available cargo and
luggage load capacity is
650 lbs (1400−750
(5 x 150) = 650 lbs).
5.Determine the combined
weight of luggage and
cargo being loaded on the
vehicle. That weight may not
safely exceed the available
cargo and luggage load
capacity calculated in Step 4.
6.If your vehicle will be towing a
trailer, the load from your
trailer will be transferred to
your vehicle. Consult
this manual to determine how
this reduces the available
cargo and luggage load
capacity of your vehicle.
SeeTowing a Trailer
on page 4-42for important
information on towing a
trailer, towing safety, and
trailering tips.
4-36 Driving Your Vehicle

Windshield Wiper Blade
Replacement
Windshield Wiper Blade
Replacement...................5-44
Tires
Tires.................................5-44
Tire Sidewall Labeling.......5-45
Tire Terminology and
Denitions.......................5-48
Ination - Tire Pressure. . . .5-51
Tire Pressure Monitor
System............................5-52
Tire Pressure Monitor
Operation........................5-54
Tire Inspection and
Rotation..........................5-57
When It Is Time for
New Tires.......................5-58
Buying New Tires.............5-59
Different Size Tires and
Wheels............................5-61
Uniform Tire Quality
Grading...........................5-62
Wheel Alignment and Tire
Balance...........................5-63
Wheel Replacement..........5-64
Tire Chains.......................5-65
If a Tire Goes Flat............5-66
Changing a Flat Tire.........5-66
Removing the Spare Tire
and Tools (H3)................5-68
Removing the Spare Tire
and Tools (H3T)..............5-69
Removing the Flat Tire
and Installing the
Spare Tire
.......................5-72
Secondary Latch
System (H3T)..................5-76
Storing a Flat or Spare
Tire and Tools (H3).........5-78
Storing a Flat or Spare
Tire and Tools (H3T).......5-80
Spare Tire........................5-82
Appearance Care
Interior Cleaning................5-83
Fabric/Carpet....................5-84
Leather.............................5-85
Instrument Panel, Vinyl,
and Other Plastic
Surfaces
..........................5-85
Care of Safety Belts.........5-85
Weatherstrips....................5-86
Washing Your Vehicle.......5-86
Cleaning Exterior Lamps/
Lenses............................5-86
Finish Care.......................5-86
Windshield, Backglass,
and Wiper Blades............5-87
Aluminum or
Chrome-Plated Wheels
and Trim
.........................5-88
Tires.................................5-89
Sheet Metal Damage........5-89
Finish Damage..................5-89
Underbody Maintenance. . . .5-89
Chemical Paint Spotting. . . .5-90
Vehicle Identication
Vehicle Identication
Number (VIN)..................5-90
Service Parts
Identication Label...........5-90
5-2 Service and Appearance Care

CAUTION (Continued)
Underinated tires pose
the same danger as
overloaded tires. The
resulting accident could
cause serious injury.
Check all tires frequently to
maintain the recommended
pressure. Tire pressure
should be checked when
your vehicle’s tires are
cold. SeeInflation - Tire
Pressure on page 5-51.
Overinated tires are more
likely to be cut, punctured,
or broken by a sudden
impact — such as when
you hit a pothole. Keep
tires at the recommended
pressure.
Worn, old tires can cause
accidents. If the tire’s tread
is badly worn, or if your
vehicle’s tires have been
damaged, replace them.
Tire Sidewall Labeling
Useful information about a tire
is molded into the sidewall.
The following illustrations are
examples of a typical P-Metric
and a LT-Metric tire sidewall.
(A) Tire Size
:The tire size code
is a combination of letters and
numbers used to dene a
particular tire’s width, height,aspect ratio, construction type,
and service description.
See the “Tire Size” illustration
later in this section for more
detail.
(B) TPC Spec (Tire
Performance Criteria
Specication)
:Original
equipment tires designed to
GM’s specic tire performance
criteria have a TPC specication
code molded onto the sidewall.
GM’s TPC specications meet
or exceed all federal safety
guidelines.
(C) DOT (Department of
Transportation)
:The
Department of Transportation
(DOT) code indicates that
the tire is in compliance
with the U.S. Department of
Transportation Motor Vehicle
Safety Standards.
Passenger (P-Metric) Tire
Service and Appearance Care 5-45

(D) Tire Identication Number
(TIN):The letters and numbers
following DOT code are the
Tire Identication Number (TIN).
The TIN shows the manufacturer
and plant code, tire size, and
date the tire was manufactured.
The TIN is molded onto both
sides of the tire, although only
one side may have the date
of manufacture.
(E) Tire Ply Material
:The type
of cord and number of plies in the
sidewall and under the tread.
(F) Uniform Tire Quality
Grading (UTQG)
:Tire
manufacturers are required to
grade tires based on three
performance factors: treadwear,
traction, and temperature
resistance. For more information,
seeUniform Tire Quality
Grading on page 5-62.(G) Maximum Cold Ination
Load Limit
:Maximum load that
can be carried and the maximum
pressure needed to support that
load. For information on
recommended tire pressure see
Inflation - Tire Pressure on
page 5-51andLoading the
Vehicle on page 4-35.
(A) Tire Size
:The tire size code
is a combination of letters and
numbers used to dene a
particular tire’s width, height,aspect ratio, construction type,
and service description.
See the “Tire Size” illustration
later in this section for more
detail.
(B) TPC Spec (Tire
Performance Criteria
Specication)
:Original
equipment tires designed to
GM’s specic tire performance
criteria have a TPC specication
code molded onto the sidewall.
GM’s TPC specications meet
or exceed all federal safety
guidelines.
(C) Dual Tire Maximum Load
:Maximum load that can be
carried and the maximum
pressure needed to support
that load when used in a dual
conguration. For information on
recommended tire pressure see
Inflation - Tire Pressure on
page 5-51andLoading the
Vehicle on page 4-35.
Light Truck (LT-Metric) Tire
5-46 Service and Appearance Care

(D) DOT (Department of
Transportation):The
Department of Transportation
(DOT) code indicates that
the tire is in compliance
with the U.S. Department of
Transportation Motor Vehicle
Safety Standards.
(E) Tire Identication Number
(TIN)
:The letters and numbers
following DOT code are the
Tire Identication Number (TIN).
The TIN shows the manufacturer
and plant code, tire size, and
date the tire was manufactured.
The TIN is molded onto both
sides of the tire, although
only one side may have the date
of manufacture.
(F) Tire Ply Material
:The type
of cord and number of plies in the
sidewall and under the tread.
(G) Single Tire Maximum Load
:Maximum load that can be
carried and the maximum
pressure needed to support that
load when used as a single.For information on recommended
tire pressure seeInflation - Tire
Pressure on page 5-51and
Loading the Vehicle on
page 4-35.
Tire Size
The following examples show
the different parts of a tire size.(A) Passenger (P-Metric) Tire
:The United States version of
a metric tire sizing system.
The letter P as the rst
character in the tire size
means a passenger vehicle
tire engineered to standards
set by the U.S. Tire and
Rim Association.
(A) Light Truck (LT-Metric)
Tire
:The United States version
of a metric tire sizing system.
The letters LT as the rst
two characters in the tire
size means a light truck tire
engineered to standards set
by the U.S. Tire and Rim
Association.
(B) Tire Width
:The three-digit
number indicates the tire section
width in millimeters from sidewall
to sidewall.
Passenger (P-Metric) Tire
Light Truck (LT-Metric) Tire
Service and Appearance Care 5-47

(C) Aspect Ratio:A two-digit
number that indicates the tire
height-to-width measurements.
For example, if the tire size
aspect ratio is 75, as shown
in item C of the light truck
(LT-Metric) tire illustration,
it would mean that the tire’s
sidewall is 75 percent as high
as it is wide.
(D) Construction Code
:A letter code is used to indicate
the type of ply construction in
the tire. The letter R means
radial ply construction; the
letter D means diagonal or
bias ply construction; and the
letter B means belted-bias
ply construction.
(E) Rim Diameter
:Diameter of
the wheel in inches.
(F) Service Description
:The service description indicates
the load range and speed
rating of a tire. The load index
can range from 1 to 279. Speed
ratings range from A to Z.
Tire Terminology and
Denitions
Air Pressure:The amount of
air inside the tire pressing
outward on each square inch
of the tire. Air pressure is
expressed in pounds per square
inch (psi) or kilopascal (kPa).
Accessory Weight
:This means
the combined weight of optional
accessories. Some examples
of optional accessories are,
automatic transmission, power
steering, power brakes, power
windows, power seats, and air
conditioning.
Aspect Ratio
:The relationship
of a tire’s height to its width.
Belt
:A rubber coated layer of
cords that is located between the
plies and the tread. Cords may
be made from steel or other
reinforcing materials.Bead
:The tire bead contains
steel wires wrapped by steel
cords that hold the tire onto
the rim.
Bias Ply Tire
:A pneumatic tire
in which the plies are laid at
alternate angles less than
90 degrees to the centerline
of the tread.
Cold Tire Pressure
:The
amount of air pressure in a tire,
measured in pounds per
square inch (psi) or kilopascals
(kPa) before a tire has built
up heat from driving. See
Inflation - Tire Pressure on
page 5-51.
Curb Weight
:The weight of a
motor vehicle with standard
and optional equipment including
the maximum capacity of fuel,
oil, and coolant, but without
passengers and cargo.
5-48 Service and Appearance Care