2009 HUMMER H2 Owners Manual

15. Tighten the nuts
rmly in a crisscross
sequence as shown
by turning the wheel
wrench with the wheel
wrench extender
clockwise.
16. When you install the wheel and tire, you must also
reinstall the center cap. Place the cap on the wheel
and tap it into place until it sits ush with the wheel.Storing a Flat or Spare Tire and
Tools (SUT)
Storing the Flat or Spare Tire
Use the following art and text to help you store the
spare or at tire back into its proper location when you
are done.
To store the at or spare tire on the tire carrier:
1. Close the tire carrier. SeeTailgate/Spare Tire
Carrier on page 2-16for tire carrier operation.
2. Place the at or spare tire onto the tire carrier with
the outside of the wheel facing you.
3. Reinstall the wheel nuts holding the spare or at
tire to the tire carrier. Tighten the nuts by hand.
5-95

4. Use the wheel wrench and the wheel wrench
extension to tighten the nuts rmly. Try to move the
tire back and forth slightly to be sure it is secure.
5. Slide the license plate holder onto the spare or at
tire. Secure it from the back of the tire carrier with
the wing nut.
If you choose not to reinstall the spare or at tire on
the vehicle, you will still need to reinstall the
license plate holder on the spare tire carrier.
5-96

Storing the Jack and Tools
To store the jack and tools:
1. Lower the jack completely.
2. Place the jack in the mounting bracket.
3. Turn the hole at the top of the jack clockwise until
the jack is held tight in the mounting bracket.
4. Push and pull on the jack and retighten if necessary
to make sure the jack is secure.
5. Place the wheel blocks in the tool bag.6. Place the remaining tools in the tool bag.
7. Make sure nothing is located under or in front of the
seat and then lift the rear driver’s side second row
seat so that the oor is exposed.
8. Place the narrow end of the tool bag under the seat
rails as shown. Slide the tool bag under the rear seat.
Be careful not to pinch the seat cables or electrical
harnesses.
9. Reinstall the strap to the seat rail.
10. Return the seat to the correct position.
5-97

Storing a Flat or Spare Tire and
Tools (SUV)
Storing the Flat or Spare Tire
Use the following art and text to help store the spare or
at tire back into its proper location when done
changing a tire.
To store the at or spare tire on the tire carrier:
1. Close the tire carrier. SeeTailgate/Spare Tire
Carrier on page 2-16for tire carrier operation.
2. Place the at or spare tire onto the tire carrier with
the outside of the wheel facing out.
3. Reinstall the wheel nuts holding the spare or the at
tire to the tire carrier. Tighten the nuts by hand.4. Use the wheel wrench and wheel wrench extension
to tighten the nuts rmly.
5. Try to move the tire back and forth slightly to make
sure it is secure.
5-98

6. Slide the license plate holder onto the spare or at
tire. Secure it from the back of the tire carrier with
the wing nut.
If you choose not to reinstall the spare or at tire on
the vehicle, you still need to reinstall the license
plate holder on the spare tire carrier.
Storing the Jack and Tools
To store the jack and tools:
1. Lower the jack completely.
2. Place the jack in the mounting bracket.
3. Turn the hole at the top of the jack clockwise until
the jack is held tight in the mounting bracket.
4. Push and pull on the jack and retighten if necessary
to make sure the jack is secure.
5-99

5. Replace the trim cover. Make sure the latches are
pushed down.
6. Place all the tools, except for the wheel blocks, in
the tool bag.
7. Place the tool bag in the storage area.8. Use the wheel blocks (B) to secure the tool bag (A)
to the bracket.
9. Turn the retainer nut (C) clockwise to secure the
wheel blocks (B) and tool bag (A) into place.
5-100

10. Return the storage tray to its original location by
pushing down on the nger depression.
Spare Tire
Your vehicle, when new, had a fully-inated spare tire.
A spare tire may lose air over time, so check its
ination pressure regularly. SeeInflation - Tire Pressure
on page 5-63andLoading the Vehicle on page 4-44
for information regarding proper tire ination and loading
your vehicle. For instruction on how to remove, install
or store a spare tire, seeRemoving the Flat Tire
and Installing the Spare Tire on page 5-90andStoring
a Flat or Spare Tire and Tools (SUT) on page 5-95
orStoring a Flat or Spare Tire and Tools (SUV)
on page 5-98.
After installing the spare tire on your vehicle, you should
stop as soon as possible and make sure the spare is
correctly inated.
Have the damaged or at road tire repaired or replaced
as soon as you can and installed back onto your vehicle.
This way, a spare tire will be available in case you need it
again. Do not mix tires and wheels of different sizes,
because they will not t. Keep your spare tire and its
wheel together.
5-101

Appearance Care
Interior Cleaning
The vehicle’s interior will continue to look its best if it is
cleaned often. Although not always visible, dust and dirt
can accumulate on the upholstery. Dirt can damage
carpet, fabric, leather, and plastic surfaces. Regular
vacuuming is recommended to remove particles from the
upholstery. It is important to keep the upholstery from
becoming and remaining heavily soiled. Soils should be
removed as quickly as possible. The vehicle’s interior
may experience extremes of heat that could cause stains
to set rapidly.
Lighter colored interiors may require more frequent
cleaning. Use care because newspapers and garments
that transfer color to home furnishings may also transfer
color to the vehicle’s interior.
When cleaning the vehicle’s interior, only use cleaners
specically designed for the surfaces being cleaned.
Permanent damage may result from using cleanerson surfaces for which they were not intended. Use glass
cleaner only on glass. Remove any accidental over-spray
from other surfaces immediately. To prevent over-spray,
apply cleaner directly to the cleaning cloth.
Notice:Using abrasive cleaners when cleaning
glass surfaces on the vehicle, could scratch
the glass and/or cause damage to the rear window
defogger. When cleaning the glass on the vehicle,
use only a soft cloth and glass cleaner.
Many cleaners contain solvents that may become
concentrated in the vehicle’s breathing space. Before
using cleaners, read and adhere to all safety instructions
on the label. While cleaning the vehicle’s interior,
maintain adequate ventilation by opening the vehicle’s
doors and windows.
Dust may be removed from small buttons and knobs
using a small brush with soft bristles.
Products that remove odors from the vehicle’s upholstery
and clean the vehicle’s glass can be obtained from your
dealer/retailer.
5-102