2009 FIAT SEDICI key

65
If the lever is equipped with the “INT
TIME” control, turn the control forward
or rearward to adjust the intermittent
wiper operation to the desired interval.WINDSHIELD WASHER
To spray windshield washer fluid, pull the
lever toward you. The windshield wipers
will automatically turn on at low speed if
they are not already on and the “INT” po-
sition is equipped.
WINDSHIELD WIPER
AND WASHER LEVER
WINDSHIELD WIPERS
To turn the windshield wipers on, move
the lever down to one of the three op-
erating positions. In the “INT” position
(for versions/markets, where provided),
the wipers operate intermittently. The
“INT” position is very convenient for dri-
ving in mist or light rain. In the “LO” po-
sition, the wipers operate at a steady low
speed. In the “HI” position, the wipers op-
erate at a steady high speed. To turn off
the wipers, move the lever back to the
“OFF” position.
Move the lever up and hold it to the
“MIST” position, the windshield wipers
will turn on continuously at low speed.
IMPORTANT Never use the window
wiper to remove ice or snow from the
windscreen. In these conditions, the wiper
is submitted to excessive effort that re-
sults in motor protection cutting in and
wiper operation inhibition for few seconds
as a consequence. If operation is not re-
stored (also after restarting the vehicle by
the ignition key) contact Fiat Dealership.
MIST
OFF
INT
LO
HI
63J301
63J302
63J303
To prevent windshield icing in
cold weather, turn on the de-
froster to heat the windshield before
and during windshield washer use.
Do not use radiator antifreeze in the
windshield washer reservoir. It can se-
verely impair visibility when sprayed
on the windshield, and can also dam-
age your vehicle’s paint.
WARNING
057-070 SEDICI LUM FL GB 1E 19-06-2009 10:32 Pagina 65

81
MAIN BEAM (HIGH BEAM)
INDICATOR LIGHT
50G055
64J045When you turn on the left or right turn
signals, the corresponding green arrow on
the instrument cluster will flash along with
the respective turn signal lights. When you
turn on the hazard warning switch, both
arrows will flash along with all of the turn
signal lights.
50G056
This indicator comes on when headlight
main beams (high beams) are turned on. TURN SIGNAL INDICATORS KEYLESS START SYSTEM
INDICATOR LIGHT
(for versions/markets, where provided)
80JM122
When you push the ignition switch for ve-
hicle with the keyless start system, this
light will come on in blue or red. If this
light comes on in blue, you can turn the
ignition switch without using an ignition
key. If this light comes on in red, you can
not turn the ignition switch without us-
ing an ignition key. For details, refer to “Ig-
nition Switch” in the “STEERING COL-
UMN CONTROLS” section.
If this light blinks in red, it reminds you that
the remote controller is not in the vehi-
cle. For details, refer to “Keyless Start Sys-
tem” in the “BEFORE DRIVING” section.REAR FOG LIGHT INDICATOR
LIGHT
(for versions/markets, where provided)
54G491
The rear fog light indicator light comes on
when the rear fog light operates. ILLUMINATION INDICATOR
LIGHT
This indicator light comes on while the po-
sition lights, tail light and/or the headlights
are on.
071-128 SEDICI LUM FL GB 1E 19-06-2009 12:05 Pagina 81

138
NOTE The number of doors involved in
the lighting operation of the interior light
depends on the vehicle specification. If
there is a switch (rubber projection) at the
door opening as shown, the door is in-
volved in the lighting operation.
SPOT LIGHT
(for versions/markets, where provided)
Push the switch to turn on the light and
push it again to turn off the light.
INTERIOR LIGHT
SWITCH
This light switch has three positions which
function as described below:
ON (1)
The light comes on and stays on regard-
less of whether the door is open or
closed.
DOOR (2)
The light comes on when the door is
opened.
After closing all doors, the light will remain
on for about 15 seconds and then fade
out. If you insert the key into the ignition
switch during that time, the light will start
to fade out immediately.
After removing the key from the ignition
switch, the light will turn on for about 15
seconds and then fade out.
OFF (3)
The light remains off even when the door
is opened.
(1) (2) (3)
64J104
79J075
79J074
129-148 SEDICI LUM FL GB 1E 19-06-2009 13:31 Pagina 138

151
Brake fluid level
Power steering (for versions/markets,
where provided) fluid level
Windshield washer fluid level
Battery solution level
Hood latch operation
Pull the hood release handle inside the
vehicle. Make sure that you cannot
open the hood all the way without re-
leasing the secondary latch. Be sure to
close the hood securely after check-
ing for proper latch operation. See “All
latches, hinges & locks” of “CHASSIS
AND BODY” in the “Periodic Main-
tenance Schedule” in the “INSPEC-
TION AND MAINTENANCE” section
for lubrication schedule.
Once a month, or each time you fill your
fuel tank, check the tire pressure using a
tire pressure gauge. Also check the tire
pressure of the spare tire.
Adjust the seat and adjustable head re-
straint (for versions/markets, where
provided).
Check the brake pedal and the park-
ing brake lever.
Adjust the mirrors.
Make sure that you and all passengers
have properly fastened your seat belts.
Make sure that all warning lights come
on as the key is turned to the “ON” or
“START” position.
Check all gauges.
Make sure that the BRAKE SYSTEM
WARNING light turns off when the
parking brake is released.
Once a week, or each time you fill your
fuel tank, perform the following under-
hood checks:
Engine oil level
Coolant level
60A187S
Make sure the hood is fully
closed and latched before
driving. If it is not, it can fly up un-
expectedly during driving, obstructing
your view and resulting in an acci-
dent.
WARNING
ENGINE OIL
CONSUMPTION
It is normal for the engine to consume
some engine oil during normal vehicle op-
eration.
The amount of engine oil consumed de-
pends on the viscosity of the oil, the qual-
ity of the oil and the conditions the vehi-
cle is driven under.
More oil is consumed during high- speed
driving and when there is frequent accel-
eration and deceleration. Under high
loads, your engine also will consume more
oil.
A new engine also consumes more oil,
since its pistons, piston rings and cylinder
walls have not yet become conditioned.
New engines reach the normal level of oil
consumption only after approximately
5000 km (3000 miles) driving.
149-168 SEDICI LUM FL GB 1E 19-06-2009 13:33 Pagina 151

152
Oil consumption: Max. 1.0 L per
1000 km (1 Qt. per 600 miles)
When judging the amount of oil con-
sumption, note that the oil may become
diluted and make it difficult to accurately
judge the true oil level.
As an example, if a vehicle is used for re-
peated short trips, and consumes a nor-
mal amount of oil, the dipstick may not
show any drop in the oil level at all, even
after 1000 km (600 miles) or more of dri-
ving. This is because the oil is gradually be-
coming diluted with fuel or moisture, mak-
ing it appear that the oil level has not
changed.
You should also be aware that the dilut-
ing ingredients evaporate out when the ve-
hicle is subsequently driven at high speeds,
such as on an expressway, making it ap-
pear that oil is excessively consumed af-
ter high- speed driving.STARTING THE ENGINE
BEFORE STARTING THE ENGINE
NOTE Gearshift levers shown in the
above illustration are examples of 5-
speed manual transaxle (for gasoline en-
gine model) and automatic transaxle.

Make sure the parking brake is set fully.
Manual transaxle – Shift into “N” (Neu-
tral) and depress the clutch pedal all the
way to the floor. Hold the clutch ped-
al while starting the engine.
Automatic transaxle – If the gearshift
lever is not in “P” (Park) position, shift
into “P” (Park). (If you need to re- start
the engine while the vehicle is moving,
shift into “N”.)
NOTE Automatic transaxle vehicles have
a starter interlock device which is de-
signed to keep the starter from operat-
ing if the transaxle is in any of the drive
positions.
Make sure that the parking
brake is set fully and the
transaxle is in Neutral (or Park for ve-
hicles with an automatic transaxle)
before attempting to start the engine.
WARNING
IMPORTANT We recommend that dur-
ing the initial period you do not drive to
full vehicle performance (e.g.: excessive ac-
celeration, long journeys at top speed,
sharp braking, etc.).
IMPORTANT When the engine is
switched off never leave the key into the
ignition switch to prevent pointless cur-
rent absorption from draining the battery.
MT
80JS008
149-168 SEDICI LUM FL GB 1E 19-06-2009 13:33 Pagina 152

153
STARTING A COLD ENGINE
(For Gasoline Engine Model)
With your foot off the accelerator pedal,
crank the engine by turning the ignition
key to “START”. Release the key when
the engine starts.
IMPORTANT
Stop turning the starter immediately af-
ter the engine has started or the starter
system can be damaged.
Do not crank the engine for more than
15 seconds at a time. If the engine does-
n’t start on the first try, wait about 15
seconds before trying again.
If the engine does not start after 15 sec-
onds of cranking, wait about 15 seconds,
then press down the accelerator pedal to
1/3 of its travel and try cranking the en-
gine again. Release the key and accelera-
tor pedal when the engine starts.
If the engine still does not start, try hold-
ing the accelerator pedal all the way to the
floor while cranking. This should clear the
engine if it is flooded.
STARTING A COLD ENGINE
(for Diesel Engine Model)
Turn the ignition switch to the “ON” po-
sition and wait until the glow plug indica-
tor goes out if it comes on. Crank the en-
gine by turning the ignition key to
“START”. Release the key when the en-
gine starts.IMPORTANT
The starter is allowed to crank the
engine up to 30 seconds. If the engine
failed to start, wait 15 seconds, then
restart cranking. Even if the third
trial failed, consult authorized Fiat
Dealership.

If the engine is started after long time
parking at extremely cold atmosphere
such as the ambient temperature is be-
low –20°C, release ignition key from
start position and stop cranking after
confirming the engine speed increase
around 800 to 1000 rpm.
STARTING WARM ENGINE
Crank the engine by turning the ignition
key to “START”. Release the key when
the engine starts.
CAUTION WHEN STOPPING
THE ENGINE WITH
TURBOCHARGER
When stopping the engine after climbing or
high speed driving, let the engine idle for
about one minute or more (if it is not pro-
hibited) to cool down the turbocharger and
engine oil. This is to prevent the engine oil
from over-deteriorating. Deteriorated en-
gine oil will damage the bearings of the tur-
bocharger.RESTARTING D20AA DIESEL
ENGINE AFTER FUEL-EMPTY
STOP
The engine stops if the engine feels fuel
emptiness. To restart the engine, stop the
vehicle, hold the ignition key in “ON” po-
sition for 5 – 10 seconds to feed fuel, then
perform above engine starting procedure.
DIESEL PARTICULATE FILTER
The diesel particulate filter filters off the
soot particles in the exhaust gas, so the
diesel particulate filter could get clogged
depending on the driving condition. The
diesel particulate filter is cleaned by the
regenerating function that combusts the
soot particles in the diesel particulate fil-
ter by raising the exhaust gas temperature
during driving or idling.
When a certain amount of soot particles
is accumulated in the diesel particulate fil-
ter, the diesel particulate filter will regen-
erate automatically to avoid clogging the
filter.
When the regeneration of the diesel par-
ticulate filter that started during driving
continues in idling, the engine revolutions
will increase by about 100 rpm and the ra-
diator fan will operate. Therefore, you
may hear a little louder engine sounds (in-
cluding the fan sounds) and/or the exhaust
gas temperature could be higher due to
combustion of the soot particles.
149-168 SEDICI LUM FL GB 1E 19-06-2009 13:33 Pagina 153

154
NOTE When you drive or idle your ve-
hicle, white smoke may be emitted de-
pending on the grade of fuel used. This is
due to the particle filter regenerating au-
tomatically, and does not affect the way
the vehicle runs.If the diesel particulate filter warning light
comes on when driving, the diesel partic-
ulate filter is nearly clogged. You should
regenerate the diesel particulate filter
when the diesel particulate filter warning
light comes on. To regenerate the diesel
particulate filter, you must drive the ve-
hicle until the light goes out, at a speed
of 50 km/h (31 mph) or higher for a while
(max. 30 minutes depending on the vehi-
cle speed).
However, you should drive carefully and
within the legal speed limit, and should
take in to consideration the surrounding
traffic conditions.
If you drive your vehicle until the light goes
out, the regeneration of the diesel partic-
ulate filter will be completed.
IMPORTANT Be sure to regenerate the
diesel particulate filter when the Diesel
Particulate Filter warning light comes on.
Failure to regenerate the diesel particu-
late filter will cause the vehicle malfunc-
tion due to the clogged filter.VEHICLE WITH KEYLESS
START SYSTEM
The ignition switch can be operated with-
out using an ignition key when the remote
controller is in an area of the vehicle oth-
er than the rear luggage area. To turn the
ignition switch, first push in the switch.
64J244
Diesel Particulate Filter warning
light
Keep away from the exhaust
pipe when the engine is run-
ning. If the diesel particulate filter is
regenerating, the exhaust gas tem-
perature could be higher.
WARNING
56KN082
79JF001
149-168 SEDICI LUM FL GB 1E 19-06-2009 13:33 Pagina 154

155
Manual transaxle vehicle
You must push in the ignition switch to
turn it from the “LOCK” position to the
“ACC” position. To return to the
“LOCK” position from the “ACC” posi-
tion, turn the ignition switch counter-
clockwise while pushing in the switch.
Automatic transaxle vehicle
To turn the ignition switch, push the
switch.
If the keyless start system blue indicator
light illuminates on the instrument cluster,
you can turn the ignition switch. If the red
indicator light illuminates, you cannot turn
the ignition switch.NOTE
 The ignition switch can be turned to the
“ACC” position when the keyless start
system blue indicator light illuminates.
The blue indicator light will illuminate
for several seconds when you push in
the ignition switch and then will turn off
to protect the system. In this case, you
must release the ignition switch and
push it again to illuminate the blue in-
dicator light.
 If the keyless start system red indicator
light illuminates, the remote controller
may not be in the vehicle or the battery
of the remote controller may be unre-
liable.
NOTE
 If the battery of the remote controller
runs down or there are strong radio
waves or noise, the operating range
may be narrower or the remote con-
troller may be inoperative.
 If the remote controller is too close to
the door glass, it may not operate.
 The ignition switch may not turn when
the remote controller is on the instru-
ment panel, in the glove box, in a stor-
age compartment, in the sun visor or
on the floor.IMPORTANT The remote controller is
a sensitive electronic instrument. To avoid
damaging it, do not expose it to impacts,
moisture or high temperature (such as on
the dashboard under direct sunlight).
If you leave any of the doors open with the
ignition switch in the “ACC” position for
a while (and no key inserted), the engine
may not start when you turn the ignition
switch to “START”. If the engine does not
start, close all doors completely or turn
the ignition switch back to the “LOCK”
position, then start the engine.
You can also turn the ignition switch by
inserting the ignition key into the slot. Re-
fer to “Ignition Switch” in the “STEERING
COLUMN CONTROLS” section.
149-168 SEDICI LUM FL GB 1E 19-06-2009 13:33 Pagina 155