2008 YAMAHA TZR50 engine

SAFETY INFORMATION.....................1-1
DESCRIPTION.....................................2-1
Left view ...........................................2-1
Right view .........................................2-2
Controls and instruments .................2-3
INSTRUMENT AND CONTROL
FUNCTIONS........................................3-1
Main switch/steering lock .................3-1
Indicator and warning lights .............3-1
Speedometer unit .............................3-2
Tachometer .......................................3-3
Handlebar switches ..........................3-3
Clutch lever .......................................3-4
Shift pedal.........................................3-4
Brake lever ........................................3-5
Brake pedal.......................................3-5
Fuel ...................................................3-5
Catalytic converter............................3-6
Fuel tank cap ....................................3-6
Fuel tank breather/overflow hose .....3-7
2-stroke engine oil ............................3-7
Fuel cock ..........................................3-8
Starter (choke) lever “
q” .................3-8
Seat...................................................3-9
Anti-theft device housing..................3-9
Rear view mirrors ..............................3-9
Sidestand ........................................3-10
Ignition circuit cut-off system .........3-10PRE-OPERATION CHECKS...............4-1
Pre-operation check list....................4-2
OPERATION AND IMPORTANT RIDING
POINTS................................................5-1
Starting a cold engine ......................5-1
Starting a warm engine ....................5-2
Shifting ..............................................5-2
Tips for reducing fuel consumption..5-3
Engine break-in.................................5-3
Parking ..............................................5-4
PERIODIC MAINTENANCE AND
MINOR REPAIR...................................6-1
Owner’s tool kit .................................6-1
Periodic maintenance and
lubrication chart ............................6-2
Removing and installing cowlings
and panels .....................................6-5
Checking the spark plug ..................6-7
Transmission oil ................................6-8
Coolant .............................................6-9
Air filter element ..............................6-12
Adjusting the carburetor .................6-12
Adjusting the throttle cable free
play ..............................................6-12
Adjusting the engine idling speed ..6-13
Tires ................................................6-14
Cast wheels ....................................6-16
Adjusting the clutch lever free
play ..............................................6-16Checking the front brake lever free
play ..............................................6-17
Adjusting the brake pedal free
play ..............................................6-17
Adjusting the shift pedal position ...6-18
Adjusting the rear brake light
switch ..........................................6-18
Checking the front and rear brake
pads.............................................6-18
Checking the brake fluid level ........6-19
Changing the brake fluid ................6-20
Drive chain slack.............................6-21
Cleaning and lubricating the drive
chain ............................................6-22
Checking and lubricating the
cables ..........................................6-23
Checking and lubricating the
throttle grip and cable .................6-23
Adjusting the Autolube pump .........6-24
Checking and lubricating the brake
and shift pedals ...........................6-24
Checking and lubricating the brake
and clutch levers .........................6-24
Checking and lubricating the
sidestand .....................................6-25
Checking the front fork ...................6-25
Checking the steering.....................6-26
Checking the wheel bearings .........6-26
Battery ............................................6-27
Replacing the fuse ..........................6-28
Replacing the headlight bulb..........6-28
TABLE OF CONTENTS
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 6

warranted by road and traffic
conditions.
• Always signal before turning or
changing lanes. Make sure that
other motorists can see you.
The posture of the operator and
passenger is important for proper
control.
• The operator should keep both
hands on the handlebar and
both feet on the operator foo-
trests during operation to
maintain control of the
motorcycle.
• The passenger should always
hold onto the operator, seat
strap, or grab bar, if equipped,
with both hands and keep both
feet on the passenger foo-
trests.
• Never carry a passenger
unless he or she can firmly pla-
ce both feet on the passenger
footrests.
Never ride under the influence of
alcohol or other drugs.
This motorcycle is designed for
on-road use only, therefore, it is
not suitable for off-road use.Protective apparel
The majority of fatalities from
motorcycle accidents are the result of
head injuries. The use of a safety hel-
met is the single most critical factor in
the prevention or reduction of head
injuries.
Always wear an approved hel-
met.
Wear a face shield or goggles.
Wind in your unprotected eyes
could contribute to an impair-
ment of vision which could delay
seeing a hazard.
The use of a jacket, heavy boots,
trousers, gloves, etc., is effective
in preventing or reducing abra-
sions or lacerations.
Never wear loose-fitting clothes,
otherwise they could catch on
the control levers, footrests, or
wheels and cause injury or an
accident.
Never touch the engine or
exhaust system during or after
operation. They become very hot
and can cause burns. Always
wear protective clothing thatcovers your legs, ankles, and
feet.
Passengers should also observe
the precautions mentioned abo-
ve.
Modifications
Modifications made to this motorcy-
cle not approved by Yamaha, or the
removal of original equipment, may
render the motorcycle unsafe for use
and may cause severe personal injury.
Modifications may also make your
motorcycle illegal to use.
Loading and accessories
Adding accessories or cargo to your
motorcycle can adversely affect sta-
bility and handling if the weight distri-
bution of the motorcycle is changed.
To avoid the possibility of an acci-
dent, use extreme caution when
adding cargo or accessories to your
motorcycle. Use extra care when
riding a motorcycle that has added
cargo or accessories. Here are some
general guidelines to follow if loading
cargo or adding accessories to your
motorcycle:
Loading
The total weight of the operator, pas-
1
SAFETY INFORMATION t
1-2
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 9

tem, an electric failure could
result, which could cause a dan-
gerous loss of lights or engine
power.
Gasoline and exhaust gas
GASOLINE IS HIGHLY FLAMMA-
BLE:
• Always turn the engine off
when refueling.
• Take care not to spill any gaso-
line on the engine or exhaust
system when refueling.
• Never refuel while smoking or
in the vicinity of an open flame.
Never start the engine or let it run
for any length of time in a closed
area. The exhaust fumes are poi-
sonous and may cause loss of
consciousness and death within
a short time. Always operate your
motorcycle in an area that has
adequate ventilation.
Always turn the engine off before
leaving the motorcycle unatten-
ded and remove the key from the
main switch. When parking the
motorcycle, note the following:
• The engine and exhaust sys-
tem may be hot, therefore,park the motorcycle in a place
where pedestrians or children
are not likely to touch these hot
areas.
• Do not park the motorcycle on
a slope or soft ground, other-
wise it may fall over.
• Do not park the motorcycle
near a flammable source (e.g. a
kerosene heater, or near an
open flame), otherwise it could
catch fire.
When transporting the motorcy-
cle in another vehicle, make sure
that it is kept upright and that the
fuel cock is turned to “ON” or
“RES” (for vacuum type) / “OFF”
(for manual type). If it should lean
over, gasoline may leak out of the
carburetor or fuel tank.
If you should swallow any gasoli-
ne, inhale a lot of gasoline vapor,
or allow gasoline to get into your
eyes, see your doctor immedia-
tely. If any gasoline spills on your
skin or clothing, immediately
wash the affected area with soap
and water and change your clot-
hes.
1
SAFETY INFORMATION t
1-4
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 11

EAU10460
Main switch/steering lock
The main switch/steering lock con-
trols the ignition and lighting systems,
and is used to lock the steering. The
various positions are described
below.
EAU10640
f
All electrical circuits are supplied with
power, and the engine can be started.
The key cannot be removed.
NOTE:
The headlight, meter lighting and tai-
llight come on automatically when the
engine is started.
EAU10660
e
All electrical systems are off. The key
can be removed.
EAU10680
m
The steering is locked, and all electri-
cal systems are off. The key can be
removed.
T
o lock the steering
1. Turn the handlebars all the way to
the left.
2. Push the key in from the “
e”
position, and then turn it to “
m”
while still pushing it.
3. Remove the key.
T
o unlock the steering
Push the key in, and then turn it to
“
e” while still pushing it.EWA10060
s s
WARNING
Never turn the key to “
e” or “m”
while the vehicle is moving, other-
wise the electrical systems will be
switched off, which may result in
loss of control or an accident.
Make sure that the vehicle is stop-
ped before turning the key to “
e”
or “
m”.
EAU11003
Indicator and warning lights
1. Coolant temperature warning light “y”
2. Oil level warning light “z”
3. Neutral indicator light “N”
4. Engine trouble warning light “ ”
5. Turn signal indicator light “
b”
EAU11020
Turn signal indicator light “cd”
This indicator light flashes when the
turn signal switch is pushed to the left
or right.
EAU11060
Neutral indicator light “N”
This indicator light comes on when
the transmission is in the neutral posi-
tion.
3
INSTRUMENT AND CONTROL FUNCTIONS
3-1
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 1

EAU11440
Coolant temperature warning light
“
y”
This warning light comes on when the
engine overheats. When this occurs,
stop the engine immediately and
allow the engine to cool.
The electrical circuit of the warning
light can be checked by turning the
key to “
f”.
If the warning light does not come on
for a few seconds, then go off, have a
Yamaha dealer check the electrical
circuit.
ECA10020
CAUTION:
Do not operate the engine if it is
overheated.
EAUM1061
Oil level warning light “z”
This warning light comes on when the
key is in the “
f” position or when the
oil level in the 2-stroke engine oil tank
is low during operation. If the warning
light comes on during operation, stop
immediately and fill the oil tank with
2-stroke engine oil of either JASO
grade “FC” or ISO grades “EG-C” or
“EG-D”. The warning light should gooff after the 2-stroke engine oil tank
has been refilled.
NOTE:
If the warning light does not come on
when the key is in the “
f” position or
does not go off after the 2-stroke
engine oil tank has been refilled, have
an Yamaha dealer check the electrical
circuit.
ECA10010
CAUTION:
Do not operate the vehicle until you
know that the engine oil level is suf-
ficient.
EAU11500
Engine trouble warning light “ ”
This warning light comes on or
flashes when an electrical circuit
monitoring the engine is defective.
When this occurs, have a Yamaha
dealer check the self-diagnosis sys-
tem.
The electrical circuit of the warning
light can be checked by turning the
key to “
f”. If the warning light does
not come on for a few seconds, then
go off, have a Yamaha dealer check
the electrical circuit.
EAU11621
Speedometer unit
1. Speedometer
2. Odometer
The speedometer unit is equipped
with a speedometer and an odometer.
The speedometer shows riding spe-
ed. The odometer shows the total dis-
tance traveled.
3
INSTRUMENT AND CONTROL FUNCTIONS
3-2
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 2

EAU11851
Tachometer
1. Tachometer
The electric tachometer allows the
rider to monitor the engine speed and
keep it within the ideal power range.
ECA10031
CAUTION:
Do not operate the engine in the
tachometer red zone.
Red zone: 10.000 r/min and above
EAU12345
Handlebar switches
1. Pass switch “j”
2. Dimmer switch “j/k”
3. Turn signal switch “c/d”
4. Horn switch“a”
1. Engine stop switch “
f/e”
2. Start switch “f”
EAU12380
Pass switch “j”
Press this switch to flash the head-
lights.
EAU12400
Dimmer switch “j/k”
Set this switch to “
j” for the high
beam and to “
k” for the low beam.
EAU12460
Turn signal switch “c/d”
To signal a right-hand turn, push this
switch to “
d”. To signal a left-hand
turn, push this switch to “
c”. When
released, the switch returns to the
center position. To cancel the turn
signal lights, push the switch in after it
has returned to the center position.
EAU12500
Horn switch “a”
Press this switch to sound the horn.
EAU12660
Engine stop switch “f/e”
Set this switch to “
f” before starting
the engine. Set this switch to “
e” to
stop the engine in case of an emer-
gency, such as when the motorcycle
overturns or when the throttle cable is
stuck.
1
2
j
k
1
2
43
3
INSTRUMENT AND CONTROL FUNCTIONS
3-3
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 3

EAU12710
Start switch “f”
Push this switch to crank the engine
with the starter.
ECA10050
CAUTION:
See page 5-1 for starting instruc-
tions prior to starting the engine.
EAU31640
Clutch lever
1. Clutch lever
The clutch lever is located at the left
handlebar grip. To disengage the
clutch, pull the lever toward the hand-
lebar grip. To engage the clutch, rele-
ase the lever. The lever should be
pulled rapidly and released slowly for
smooth clutch operation.
The clutch lever is equipped with a
clutch switch, which is part of the
starting circuit cut-off system. (See
page 3-10.)
EAU12870
Shift pedal
1. Shift pedal
The shift pedal is located on the left
side of the engine and is used in com-
bination with the clutch lever when
shifting the gears of the 6-speed
constant-mesh transmission equip-
ped on this motorcycle.
1
j
k
13
INSTRUMENT AND CONTROL FUNCTIONS
3-4
5WX-F8199-E2.qxd 29/05/2006 17:53 Página 4

EAU12890
Brake lever
1. Brake lever
The brake lever is located at the right
handlebar grip. To apply the front bra-
ke, pull the lever toward the handle-
bar grip.
EAU12941
Brake pedal
1. Brake pedal
The brake pedal is on the right side of
the motorcycle. To apply the rear bra-
ke, press down on the brake pedal.
EAU13210
Fuel
1. Fuel tank filler tube
2. Fuel level
Make sure that there is sufficient fuel
in the tank. Fill the fuel tank to the
bottom of the filler tube as shown.
EWA10880
s s
WARNING
Do not overfill the fuel tank,
otherwise it may overflow
when the fuel warms up and
expands.
Avoid spilling fuel on the hot
engine.
1
1
3
INSTRUMENT AND CONTROL FUNCTIONS
3-5
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 5