2008 YAMAHA TZR50 recommended oil

NOTE:
The fuel tank cap cannot be closed
unless the key is in the lock. In addi-
tion, the key cannot be removed if the
cap is not properly closed and loc-
ked.
EWA11090
s s
WARNING
Make sure that the fuel tank cap is
properly closed before riding.
EAUB1300
Fuel tank breather/overflow
hose
1. Fuel tank breather/overflow hose
Before operating the motorcycle:
Check the fuel tank breather/over-
flow hose connection.
Check the fuel tank
breather/overflow hose for
cracks or damage, and replace it
if damaged.
Make sure that the end of the fuel
tank breather/overflow hose is
not blocked, and clean it if
necessary.
Make sure that the end of the fuel
tank breather/overflow hose is
positioned inside of the clamp.
EAU13460
2-stroke engine oil
1. 2-stroke engine oil tank
2. 2-stroke engine oil tank cap
Make sure that there is sufficient oil in
the 2-stroke engine oil tank. Add the
recommended 2-stroke engine oil if
necessary.
NOTE:
Make sure that the 2-stroke engine oil
tank cap is properly installed.
Recommended oil:
Yamalube 2 or equivalent 2-stroke
engine oil (JASO grade “FC”, or
ISO grades “EG-C” or “EG-D”)
Oil quantity:
1.4 L (1.48 US qt) (1.23 Imp qt)
12
1
3
INSTRUMENT AND CONTROL FUNCTIONS
3-7
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 7

EAU15603
Pre-operation check list
4
PRE-OPERATION CHECKS
4-2
ITEM CHECKS PAGE
• Check fuel level in fuel tank.
Fuel• Refuel if necessary. 3-5, 3-6, 3-7
• Check fuel line for leakage.
• Check oil level in oil tank.
2-stroke engine oil• If necessary, add recommended oil to specified level. 3-7
• Check vehicle for oil leakage.
Transmission oil• Check oil level in transmission case.
• If necessary, add recommended oil to specified level.6-8
• Check coolant level in reservoir.
Coolant• If necessary, add recommended coolant to specified level. 6-9
• Check cooling system for leakage.
• Check operation.
• If soft or spongy, have Yamaha dealer bleed hydraulic system.
• Check brake pads for wear.
Front brake• Replace if necessary. 3-5, 6-17 ~ 6-20
• Check fluid level in reservoir.
• If necessary, add recommended brake fluid to specified level.
• Check hydraulic system for leakage.
• Check operation.
• If soft or spongy, have Yamaha dealer bleed hydraulic system.
• Check brake pads for wear.
Rear brake• Replace if necessary. 3-5, 6-17 ~ 6-20
• Check fluid level in reservoir.
• If necessary, add recommended brake fluid to specified level.
• Check hydraulic system for leakage.
• Check operation.
Clutch• Lubricate cable if necessary.
3-4, 6-16, 6-24
• Check lever free play.
• Adjust if necessary.
• Make sure that operation is smooth.
Throttle grip• Check cable free play.
6-12, 6-23
• If necessary, have Yamaha dealer adjust cable free play and lubricate
cable and grip housing.
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 13

2. Remove the oil check bolt, andthen check the oil level.
NOTE:
The oil should be at the brim of the
check hole.
3. If the oil is below the brim of thecheck hole, remove the oil filler
cap, add sufficient oil of the
recommended type to raise it to
the correct level, and then install
the oil filler cap.
4. Install the oil check bolt, and then tighten it to the specified torque.
To change the transmission oil 1. Place an oil pan under the trans- mission oil case to collect the
used oil.
2. Remove the drain bolt and the oil check bolt to drain the oil.
3. Install the drain bolt and the check bolt, and then tighten them
to the specified torque. 4. Remove the oil filler cap, add the
specified amount of the recom-
mended transmission oil, and
then install and tighten the oil
filler cap.
ECAM1020
CAUTION:
Make sure that no foreign material
enters the transmission case.
5. Start the engine and let it idle for several minutes while checking
the transmission oil case for oil
leakage. If oil is leaking, imme-
diately turn the engine off and
check for the cause.
EAU20070
Coolant
The coolant level should be checked
before each ride. In addition, the coo-
lant must be changed at the intervals
specified in the periodic maintenance
and lubrication chart.
EAU33030
Changing the coolantEWA10380
s s WARNING
Never attempt to remove the radia-
tor cap when the engine is hot.
The coolant must be changed at the
intervals specified in the periodic
maintenance and lubrication chart.
Have a Yamaha dealer change the
coolant.
EAU20080
To check the coolant level 1. Place the vehicle on a level surfa- ce and hold it in an upright posi-
tion.
Recommended transmission oil:See page 8-1.
Oil change quantity: 0.82 L (0.87 US qt) (0.72 Imp.qt)
Tightening torque:Transmission oil drain bolt:17.5 Nm (1.7 m•kgf, 12.7 ft•lbf)
Oil check bolt: 6 Nm (0.6 m•kgf, 4.3 ft•lbf)
Tightening torque:Oil check bolt: 6 Nm (0.6 m•kgf, 4.3 ft•lbf)6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-9
5WX-F8199-E2.qxd 31/05/2006 10:23 Página 9

fluid is above the minimum level mark
and replenish if necessary. A low bra-
ke fluid level may indicate worn brake
pads and/or brake system leakage. If
the brake fluid level is low, be sure to
check the brake pads for wear and
the brake system for leakage.
Observe these precautions:
When checking the fluid level,
make sure that the top of the bra-
ke fluid reservoir is level.
Use only the recommended qua-
lity brake fluid, otherwise the rub-
ber seals may deteriorate, cau-
sing leakage and poor braking
performance.
Refill with the same type of brake
fluid. Mixing fluids may result in a
harmful chemical reaction and
lead to poor braking performan-
ce.
Be careful that water does not
enter the brake fluid reservoir
when refilling. Water will signifi-cantly lower the boiling point of
the fluid and may result in vapor
lock.
Brake fluid may deteriorate pain-
ted surfaces or plastic parts.
Always clean up spilled fluid
immediately.
As the brake pads wear, it is nor-
mal for the brake fluid level to
gradually go down. However, if
the brake fluid level goes down
suddenly, have a Yamaha dealer
check the cause.
EAU22730
Changing the brake fluid
Have a Yamaha dealer change the
brake fluid at the intervals specified in
the NOTE after the periodic mainte-
nance and lubrication chart. In addi-
tion, have the oil seals of the master
cylinders and calipers as well as the
brake hoses replaced at the intervals
listed below or whenever they are
damaged or leaking.
Oil seals: Replace every two
years.
Brake hoses: Replace every four
years.
Recommended brake fluid:
DOT 4
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-20
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 20

ECA11110
CAUTION:
Do not use engine oil or any other
lubricants for the drive chain, as
they may contain substances that
could damage the O-rings.
EAU23100
Checking and lubricating the
cables
The operation of all control cables
and the condition of the cables
should be checked before each ride,
and the cables and cable ends should
be lubricated if necessary. If a cable is
damaged or does not move smoothly,
have a Yamaha dealer check or repla-
ce it.
EWA10720
s s
WARNING
Damage to the outer sheath may
interfere with proper cable opera-
tion and will cause the inner cable
to rust. Replace a damaged cable
as soon as possible to prevent
unsafe conditions.
EAU23111
Checking and lubricating the
throttle grip and cable
The operation of the throttle grip
should be checked before each ride.
In addition, the cable should be lubri-
cated at the intervals specified in the
periodic maintenance chart.
Recommended lubricant:
Engine oil
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-23
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 23

EAU23200
Checking and lubricating the
sidestand
The operation of the sidestand should
be checked before each ride, and the
sidestand pivot and metal-to-metal
contact surfaces should be lubricated
if necessary.
EWA10730
s s
WARNING
If the sidestand does not move up
and down smoothly, have a Yama-
ha dealer check or repair it.
EAU23271
Checking the front fork
The condition and operation of the
front fork must be checked as follows
at the intervals specified in the perio-
dic maintenance and lubrication
chart.
To check the condition
EWA10750
s s
WARNING
Securely support the motorcycle so
that there is no danger of it falling
over.
Check the inner tubes for scratches,
damage and excessive oil leakage.
To check the operation
1. Place the motorcycle on a level
surface and hold it in an upright
position.2. While applying the front brake,
push down hard on the handle-
bars several times to check if the
front fork compresses and
rebounds smoothly.
ECA10590
CAUTION:
If any damage is found or the front
fork does not operate smoothly,
have a Yamaha dealer check or
repair it.
Recommended lubricant:
Lithium-soap-based grease (all-
purpose grease)
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-25
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 25

DimensionsOverall length
2202 mm (86.7 in)
Overall width
689 mm (27.1 in)
Overall height
1175 mm (46.3 in)
Seat height
820 mm (32.3 in)
Wheelbase
1341 mm (52.8 in)
Ground clearance
151 mm (5.94 in)
Minimum turning radius
2900 mm (114.2 in)
WeightWith oil and fuel
124 kg (273 lb)
EngineEngine type
Liquid cooled 2-stroke
Cylinder arrangement
Forward-inclined single cylinder
Displacement
49.7 cm
3(3.03 cu*in)
Bore x stroke
40.3 x 39.0 mm (1.58 x 1.53 in)
Compression ratio
11.5:1
Starting system
Electric starter
Lubrication system
Separate lubrication (Yamaha autolube)
Oil type or gradeRecommended engine oil grade
SAE10W30 type SE motor oil
Cooling systemRadiator capacity (including all routes)
0.70 L (0.74 US qt) (0.62 Imp qt)
Coolant reservoir capacity (up to the maxi-
mum level mark)
0.29L (0.31 US qt) ( 0.26 Imp qt)
Air filterAir filter element
Wet element
Recommended fuelRecommended fuel
Unleaded fuel
Fuel tank capacity
13.8 L (3.65 US gal) (3.04 Imp gal)
Fuel reserve amount
2.2 L (0.58 US gal) (0.48 Imp gal)
CarburetorManufacturer
Dell’Orto
Type x quantity
PHBN 16 x 1
Spark plug (s)Manufacturer/model
NGK/BR 9 ES
Spark plug gap
0.6 ~ 0.7 mm (0.023 ~ 0.027 in)
ClutchClutch type
Wet, multiple-disc
TransmissionPrimary reduction system
Helical gear
Primary reduction ratio
71 x 20 (3.55)
Secondary reduction system
Chain drive
Secondary reduction ratio
60 x 11 (5.45)
Transmission type
Constant mesh 6-speed
Operation
Left foot operation
Gear ratio1-
36 x 12 (3.00)
2-
33 x 16 (2.062)
3-
29 x 19 (1.526)
4-
27 x 22 (1.227)
5-
25 x 24 (1.041)
6-
24 x 25 (0.960)
ChassisFrame type
Double cradle
Caster angle
25 º
Trail
90 mm (3.54 in)
8
SPECIFICATIONS
8-1
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 38

Front tireType
Tubeless
Size
100/80-17 52H
Manufacturer/model
Pirelli / Sport Demon
Continental/Conti-Twist SM
Rear tireType
Tubeless
Size
130/70-17 62H
Manufacturer/model
Pirelli / Sport Demon
Continental/Conti-Twist SM
LoadingMaximum load
196 kg (432.18 lb)
Load is total weight of the equipement, dri-
ver, passenger and accessories
Tire air pressure (measured on cold
tires)
Loading condition
0–90 kg (0–198 lb)
Front
180 kPa (26 psi) (1.8 kgf/cm
2)
Rear
200 kPa (28 psi) (2.0 kgf/cm
2)
Loading condition
90 kg (198 lb)–Maximum load
Front
190 kPa (27 psi) (1,9 kgf/cm
2)Rear
230 kPa (33 psi) (2,3 kgf/cm
2)
Front wheelWheel type
Cast wheel
Rim size
17 x MT2.75
Rear wheelWheel type
Cast wheel
Rim size
17 x MT3.50
Front brakeType
Single disc brake
Operation
Right hand operation
Recommended fluid
DOT 4
Rear brakeType
Single disc brake
Operation
Right foot operation
Recommended fluid
DOT 4
Front suspensionType
Telescopic fork
Spring/shock absorber type
Coil spring/oil damper
Wheel travel
108 mm (4.25 in)
Rear suspensionType
Unit swing
Spring/shock absorber type
Coil spring/oil damper
Wheel travel
89.2 mm (3.51 in)
Electrical systemIgnition system
MORIC
Charging system
Transistor
BatteryManufacturer/model
TIAJIN TONG YEE INDUSTRIAL
CO. LTD. / GS GT4L-BS
Voltage, capacity
12V-3Ah
Bulb voltage, wattage x quantityHeadlight
12 V, 25.0 W / 25.0 W x 2
Tail/brake light
12 V, 21.0 W / 5.0 W x 2
Front turn signal light
12 V, 16.0 W x 2
Rear turn signal light
12 V, 10.0 W x 2
License plate light
12 V, 5.0 W x 1
Meter lighting
LED
High beam Indicator light
LED
Turn signal indicator light
8
SPECIFICATIONS
8-2
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 39