2008 YAMAHA TZR50 engine

EAU40370
Air filter element
The air filter element must be cleaned
and replaced at the intervals specified
in the periodic maintenance and lubri-
cation chart. Have a Yamaha dealer
clean and replace the air filter ele-
ment.
EAU21280
Adjusting the carburetor
The carburetor is an important part of
the engine and requires very sophisti-
cated adjustment. Therefore, most
carburetor adjustments should be left
to a Yamaha dealer, who has the
necessary professional knowledge
and experience. The adjustment des-
cribed in the following section, howe-
ver, may be serviced by the owner as
part of routine maintenance.
ECA10550
CAUTION:
The carburetor has been set and
extensively tested at the Yamaha
factory. Changing these settings
without sufficient technical know-
ledge may result in poor perfor-
mance of or damage to the engine.
EAU21370
Adjusting the throttle cable
free play
The throttle cable free play should
measure 4 ~ 6 mm (0.15 ~ 0.23 in) at
the throttle grip. Periodically check
the throttle cable free play and, if
necessary, adjust it as follows.
1. Throttle cable free play
NOTE:
The engine idling speed must be
correctly adjusted before checking
and adjusting the throttle cable free
play.
1. To increase the throttle cable free
play, turn the adjusting nut in
direction (a). To decrease the
ef
g(a)
(b)1
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-12
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 12

throttle cable free play, turn the
adjusting nut in direction (b).EAU33481
Adjusting the engine idling
speed
The engine idling speed must be
checked and, if necessary, adjusted
as follows at the intervals specified in
the periodic maintenance and lubrica-
tion chart.
The engine should be warm before
making this adjustment.
NOTE:
The engine is warm when it quickly
responds to the throttle.
1. Remove panel B. (See page 6-5.)
1. Idle adjusting screw
2. Check the engine idling speed
and, if necessary, adjust it to spe-
cification by turning the idle
adjusting screw. To increase the
engine idling speed, turn the
screw in direction (a). To decrea-
se the engine idling speed, turn
the screw in direction (b).
NOTE:
If the specified idling speed cannot be
obtained as described above, have a
Yamaha dealer make the adjustment.
3. Install the panel.
Engine idling speed:
1.600 ~ 1.900 r/min
1(a)
(b)
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-13
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 13

EAUT1220
Checking the front brake
lever free play
1. Brake lever free play
The brake lever free play should mea-
sure 2~5 mm (0.08~0.20 in) as shown.
Periodically check the brake lever free
play and, if necessary, have a Yamaha
dealer check the brake system.
EWA10640
s s
WARNING
An incorrect brake lever free play
indicates a hazardous condition in
the brake system. Do not operate
the motorcycle until the brake sys-
tem has been checked or repaired
by a Yamaha dealer.
EAUM1352
Adjusting the brake pedal
free play
1. Brake pedal free play
The brake pedal free play should
measure 10~15 mm (0.39~0.59 in) as
shown. Periodically check the brake
pedal free play and, if necessary, have
a Yamaha dealer adjust it.
EWAM1010
s s
WARNING
You are hereby informed that any
attempt to change the engine or
any other part to increase the sco-
oter’s performance or power is
strictly forbidden by law.
Any change resulting in an
increase of the vehicle’s maxi-
mum speed or in an increase of
the engine’s capacity entails a
category classification shift
from scooter to light motorcy-
cle, with all the consequences
relating to the latter category,
compelling the owner to:
- proceed with a new certifica-
tion,
- have the vehicle registered,
- hold a driving license (pur-
suant to the new legislation).
In addition, you are informed that
such changes will bar you from
insurance coverage insofar as
insurance policies expressly stipu-
late that such technical changes
brought with a view to enhancing
performance are forbidden.
For the above-mentioned reasons,
any violation of the rules forbidding
personal or otherwise third-party
interventions is punishable by law
with penalties (including seizure of
the vehicle) to which, as the case
may be, penalties may be added
relating to the failure to wear a
1
1
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-17
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 17

1. Remove the cotter pin from the
axle nut, and then loosen the axle
nut.
2. Loosen the chain puller locknut
at each end of the swingarm.
3. To tighten the drive chain, turn
the adjusting nut at each end of
the swingarm in direction (a). To
loosen the drive chain, turn the
adjusting nut at each end of the
swingarm in direction (b), and
then push the rear wheel forward.
NOTE:
Using the alignment marks on each
side of the swingarm, make sure that
both adjusting nuts are in the same
position for proper wheel alignment.
ECA10570
CAUTION:
Improper drive chain slack will
overload the engine as well as
other vital parts of the motorcycle
and can lead to chain slippage or
breakage. To prevent this from
occurring, keep the drive chain
slack within the specified limits.
4. Tighten the locknuts, and then
tighten the axle nut to the speci-
fied torque.
5. Insert a new cotter pin into the
axle nut, and then bend its ends
as shown.
NOTE:
Make sure that two notches in the
axle nut are aligned with the hole
through the wheel axle, otherwise
further tighten the axle nut until they
are.
EWA10700
s s
WARNING
Always use a new cotter pin for the
axle nut.
EAU23022
Cleaning and lubricating the
drive chain
The drive chain must be cleaned and
lubricated at the intervals specified in
the periodic maintenance and lubrica-
tion chart, otherwise it will quickly
wear out, especially when riding in
dusty or wet areas. Service the drive
chain as follows.
ECA10581
CAUTION:
The drive chain must be lubricated
after washing the motorcycle and
riding in the rain.
1. Clean the drive chain with kero-
sene and a small soft brush.
ECA11120
CAUTION:
To prevent damaging the O-rings,
do not clean the drive chain with
steam cleaners, high-pressure
washers or inappropriate solvents.
2. Wipe the drive chain dry.
3. Thoroughly lubricate the drive
chain with a special O-ring chain
lubricant.
Tightening torque:
Axle nut:
90 Nm (9.0 m•kgf, 65.1 ft•lbf)
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-22
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 22

ECA11110
CAUTION:
Do not use engine oil or any other
lubricants for the drive chain, as
they may contain substances that
could damage the O-rings.
EAU23100
Checking and lubricating the
cables
The operation of all control cables
and the condition of the cables
should be checked before each ride,
and the cables and cable ends should
be lubricated if necessary. If a cable is
damaged or does not move smoothly,
have a Yamaha dealer check or repla-
ce it.
EWA10720
s s
WARNING
Damage to the outer sheath may
interfere with proper cable opera-
tion and will cause the inner cable
to rust. Replace a damaged cable
as soon as possible to prevent
unsafe conditions.
EAU23111
Checking and lubricating the
throttle grip and cable
The operation of the throttle grip
should be checked before each ride.
In addition, the cable should be lubri-
cated at the intervals specified in the
periodic maintenance chart.
Recommended lubricant:
Engine oil
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-23
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 23

EAU23120
Adjusting the Autolube pump
The Autolube pump is a vital and sop-
histicated component of the engine,
which must be adjusted by a Yamaha
dealer at the intervals specified in the
periodic maintenance and lubrication
chart.
EAU23131
Checking and lubricating the
brake and shift pedals
The operation of the brake and shift
pedals should be checked before
each ride, and the pedal pivots
should be lubricated if necessary.
EAU23140
Checking and lubricating the
brake and clutch levers
The operation of the brake and clutch
levers should be checked before each
ride, and the lever pivots should be
lubricated if necessary.
Recommended lubricant:
Lithium-soap-based grease (all-
purpose grease)
j
kj
q
Recommended lubricant:
Lithium-soap-based grease (all-
purpose grease)
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-24
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 24

EAU23280
Checking the steering
Worn or loose steering bearings may
cause danger. Therefore, the opera-
tion of the steering must be checked
as follows at the intervals specified in
the periodic maintenance and lubrica-
tion chart.
1. Place a stand under the engine to
raise the front wheel off the
ground.
EWA10750
s s
WARNING
Securely support the motorcycle so
that there is no danger of it falling
over.
2. Hold the lower ends of the front
fork legs and try to move them
forward and backward. If any freeplay can be felt, have a Yamaha
dealer check or repair the stee-
ring.
EAU23290
Checking the wheel bearings
The front and rear wheel bearings
must be checked at the intervals spe-
cified in the periodic maintenance and
lubrication chart. If there is play in the
wheel hub or if the wheel does not
turn smoothly, have a Yamaha dealer
check the wheel bearings.
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-26
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 26

6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-32
EAU25921
Troubleshooting charts
Starting problems or poor engine performanceEWA10840
s s
WARNING
Keep away open flames and do not smoke while checking or working on the fuel system.
Check the fuel level in
the fuel tank.
1. FuelThere is enough fuel.
There is no fuel.Check the compression.
Supply fuel.
The engine does not start.
Check the compression.
Operate the electric starter.
2. CompressionThere is compression.
There is no compression.Check the ignition.
Have a Yamaha dealer
check the vehicle.
Remove the spark plug
and check the electrodes.
3. IgnitionWipe off with a dry cloth and correct the
spark plug gap, or replace the spark plug.
Have a Yamaha dealer check the vehicle.
The engine does not start.
Have a Yamaha dealer
check the vehicle.
The engine does not start.
Check the battery.
Operate the electric starter.
4. BatteryThe engine turns over
quickly.
The engine turns over
slowly.The battery is good.
Check the battery lead connections,
and charge the battery if necessary.
Dry
We tOpen the throttle halfway and operate
the electric starter.
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 32