2008 YAMAHA TZR50 maintenance

EAU21560
Tires
To maximize the performance, durabi-
lity, and safe operation of your
motorcycle, note the following points
regarding the specified tires.
Tire air pressure
The tire air pressure should be chec-
ked and, if necessary, adjusted befo-
re each ride.
EWA10500
s s
WARNING
The tire air pressure must be
checked and adjusted on cold
tires (i.e., when the temperatu-
re of the tires equals the
ambient temperature).
The tire air pressure must be
adjusted in accordance with
the riding speed and with the
total weight of rider, passenger,
cargo, and accessories appro-
ved for this model.EWA11020
s s
WARNING
Because loading has an enormous
impact on the handling, braking,
performance and safety characte-
ristics of your motorcycle, you
should keep the following precau-
tions in mind.
NEVER OVERLOAD THE
MOTORCYCLE! Operation of
an overloaded motorcycle may
result in tire damage, loss ofcontrol, or severe injury. Make
sure that the total weight of
rider, passenger, cargo, and
accessories does not exceed
the specified maximum load
for the vehicle.
Do not carry along loosely pac-
ked items, which can shift
during a ride.
Securely pack the heaviest
items close to the center of the
motorcycle and distribute the
weight evenly on both sides.
Adjust the suspension and tire
air pressure with regard to the
load.
Check the tire condition and air
pressure before each ride.
Tire air pressure (measured on cold
tires):
Up to 90 kg (198 lb):
Front:
180 kPa (25 psi) (1.8 kgf/cm
2)
Rear:
200 kPa (28 psi) (2.0 kgf/cm
2)
90 kg (198 lb) to maximum load:
Front:
190 kPa (27 psi) (1.9 kgf/cm
2)
Rear:
230 kPa (33 psi) (2.3 kgf/cm
2)
Maximum load*:
196 kg (432.18 lb)
* Total weight of rider, passenger,
cargo and accessories
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-14
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 14

Tire inspection
1. Tire tread depth
The tires must be checked before
each ride. If the center tread depth
reaches the specified limit, if the tire
has a nail or glass fragments in it, or if
the sidewall is cracked, have a Yama-
ha dealer replace the tire immediately.
NOTE:
The tire tread depth limits may differ
from country to country. Always
comply with the local regulations.
Tire information
This motorcycle is equipped with cast
wheels and tubeless tires.
EWA10460
s s
WARNING
The front and rear tires should
be of the same make and
design, otherwise the handling
characteristics of the vehicle
cannot be guaranteed.
After extensive tests, only the
tires listed below have been
approved for this model by
Yamaha Motor España, S.A.
EWA10470
s s
WARNING
Have a Yamaha dealer replace
excessively worn tires. Besides
being illegal, operating the
vehicle with excessively worn
tires decreases riding stability
and can lead to loss of control.
The replacement of all wheel
and brake related parts, inclu-
ding the tires, should be left to
a Yamaha dealer, who has the
necessary professional know-
ledge and experience.
Front tire:
Size:
100/80-17 MC 52 H
Manufacturer/model:
Pirelli / SPORT DEMON
Continental/Conti-Twist SM
Rear tire:
Size:
130/70-17 M/C 62 H
Manufacturer/model:
Pirelli / SPORT DEMON
Continental/Conti-Twist SM
Minimum tire tread depth (front
and rear):
1.6 mm (0.06 in)
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-15
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 15

EAU21960
Cast wheels
To maximize the performance, durabi-
lity, and safe operation of your
motorcycle, note the following points
regarding the specified wheels.
The wheel rims should be chec-
ked for cracks, bends or warpage
before each ride. If any damage
is found, have a Yamaha dealer
replace the wheel. Do not
attempt even the smallest repair
to the wheel. A deformed or crac-
ked wheel must be replaced.
The wheel should be balanced
whenever either the tire or wheel
has been changed or replaced.
An unbalanced wheel can result
in poor performance, adverse
handling characteristics, and a
shortened tire life.
Ride at moderate speeds after
changing a tire since the tire sur-
face must first be “broken in” for
it to develop its optimal characte-
ristics.
EAU22041
Adjusting the clutch lever
free play
1. Clutch lever free play
2. Locknut (clutch lever)
3. Clutch lever free play adjusting bolt
The clutch lever free play should mea-
sure 10~15 mm (0.39~0.59 in) as
shown. Periodically check the clutch
lever free play and, if necessary,
adjust it as follows.
1. Loosen the locknut at the clutch
lever.
2. To increase the clutch lever free
play, turn the adjusting bolt in
direction (a). To decrease the
clutch lever free play, turn the
adjusting bolt in direction (b).
NOTE:
If the specified clutch lever free play
could be obtained as described abo-
ve, tighten the locknut and skip the
rest of the procedure, otherwise pro-
ceed as follows.
3. Fully turn the adjusting bolt at the
clutch lever in direction (a) to loo-
sen the clutch cable.
4. Loosen the locknut at the crank-
case.
5. To increase the clutch lever free
play, turn the adjusting nut in
direction (a). To decrease the
clutch lever free play, turn the
adjusting nut in direction (b).
6. Tighten the locknut at the clutch
lever and the crankcase.
ab
j
kj
q
1 23
ab
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-16
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 16

EAUT1220
Checking the front brake
lever free play
1. Brake lever free play
The brake lever free play should mea-
sure 2~5 mm (0.08~0.20 in) as shown.
Periodically check the brake lever free
play and, if necessary, have a Yamaha
dealer check the brake system.
EWA10640
s s
WARNING
An incorrect brake lever free play
indicates a hazardous condition in
the brake system. Do not operate
the motorcycle until the brake sys-
tem has been checked or repaired
by a Yamaha dealer.
EAUM1352
Adjusting the brake pedal
free play
1. Brake pedal free play
The brake pedal free play should
measure 10~15 mm (0.39~0.59 in) as
shown. Periodically check the brake
pedal free play and, if necessary, have
a Yamaha dealer adjust it.
EWAM1010
s s
WARNING
You are hereby informed that any
attempt to change the engine or
any other part to increase the sco-
oter’s performance or power is
strictly forbidden by law.
Any change resulting in an
increase of the vehicle’s maxi-
mum speed or in an increase of
the engine’s capacity entails a
category classification shift
from scooter to light motorcy-
cle, with all the consequences
relating to the latter category,
compelling the owner to:
- proceed with a new certifica-
tion,
- have the vehicle registered,
- hold a driving license (pur-
suant to the new legislation).
In addition, you are informed that
such changes will bar you from
insurance coverage insofar as
insurance policies expressly stipu-
late that such technical changes
brought with a view to enhancing
performance are forbidden.
For the above-mentioned reasons,
any violation of the rules forbidding
personal or otherwise third-party
interventions is punishable by law
with penalties (including seizure of
the vehicle) to which, as the case
may be, penalties may be added
relating to the failure to wear a
1
1
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-17
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 17

crash helmet, the failure to identify
the vehicle, the failure to have an
insurance, or the failure to hold a
driving license.
EAUB1100
Adjusting the shift pedal
position
1. Shift pedal
The top of the shift pedal should be
positioned approximately 65 mm
(2.5590 in) below the top of the foo-
trest as shown. Periodically check the
shift pedal position and, if necessary,
have a Yamaha dealer adjust it.
EAU22270
Adjusting the rear brake light
switch
1. Rear brake light switch
2. Rear brake light switch adjusting nut
The rear brake light switch, which is
activated by the brake pedal, is pro-
perly adjusted when the brake light
comes on just before braking takes
effect. If necessary, adjust the brake
light switch as follows.
Turn the adjusting nut while holding
the rear brake light switch in place. To
make the brake light come on earlier,
turn the adjusting nut in direction (a).
To make the brake light come on later,
turn the adjusting nut in direction (b).
EAU22390
Checking the front and rear
brake pads
The front and rear brake pads must
be checked for wear at the intervals
specified in the periodic maintenance
and lubrication chart.
EAU22430
Front brake pads
1. Brake pad wear indicator grove
Each front brake pad is provided with
wear indicator grooves, which allow
you to check the brake pad wear wit-
hout having to disassemble the brake.
To check the brake pad wear, check
the wear indicator grooves. If a brake
pad has worn to the point that the
wear indicator grooves have almost
11
a
b
1 2
1
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-18
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 18

disappeared, have a Yamaha dealer
replace the brake pads as a set.
EAU22480
Rear brake pads
1. Brake pad wear indicator grove
Each rear brake pad is provided with
a wear indicator groove, which allows
you to check the brake pad wear wit-
hout having to disassemble the brake.
Check the brake pad wear as follows.
1. Remove the brake caliper bolt,
and then tilt the caliper forward to
inspect the wear indicator groo-
ve. If a brake pad has worn to the
point that the wear indicator gro-
ove has almost disappeared,
have a Yamaha dealer replace
the brake pads as a set.2. Install the brake caliper bolt, and
then tighten it to the specified
torque.
EAU22580
Checking the brake fluid
level
Front
Rear
Insufficient brake fluid may allow air
to enter the brake system, possibly
causing it to become ineffective.
Before riding, check that the brake
max.
min.
min
Tightening torque:
Brake caliper bolt:
30 Nm (3.0 m.kgf, 21.7 ft.lbf)
11
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-19
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 19

fluid is above the minimum level mark
and replenish if necessary. A low bra-
ke fluid level may indicate worn brake
pads and/or brake system leakage. If
the brake fluid level is low, be sure to
check the brake pads for wear and
the brake system for leakage.
Observe these precautions:
When checking the fluid level,
make sure that the top of the bra-
ke fluid reservoir is level.
Use only the recommended qua-
lity brake fluid, otherwise the rub-
ber seals may deteriorate, cau-
sing leakage and poor braking
performance.
Refill with the same type of brake
fluid. Mixing fluids may result in a
harmful chemical reaction and
lead to poor braking performan-
ce.
Be careful that water does not
enter the brake fluid reservoir
when refilling. Water will signifi-cantly lower the boiling point of
the fluid and may result in vapor
lock.
Brake fluid may deteriorate pain-
ted surfaces or plastic parts.
Always clean up spilled fluid
immediately.
As the brake pads wear, it is nor-
mal for the brake fluid level to
gradually go down. However, if
the brake fluid level goes down
suddenly, have a Yamaha dealer
check the cause.
EAU22730
Changing the brake fluid
Have a Yamaha dealer change the
brake fluid at the intervals specified in
the NOTE after the periodic mainte-
nance and lubrication chart. In addi-
tion, have the oil seals of the master
cylinders and calipers as well as the
brake hoses replaced at the intervals
listed below or whenever they are
damaged or leaking.
Oil seals: Replace every two
years.
Brake hoses: Replace every four
years.
Recommended brake fluid:
DOT 4
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-20
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 20

EAU22760
Drive chain slack
The drive chain slack should be chec-
ked before each ride and adjusted if
necessary.
EAU22781
To check the drive chain slack
1. Drive chain slack
1. Place the motorcycle on the
sidestand.
NOTE:
When checking and adjusting the dri-
ve chain slack, there should be no
weight on the motorcycle.
2. Shift the transmission into the
neutral position.3. Move the rear wheel by pushing
the motorcycle to locate the tigh-
test portion of the drive chain,
and then measure the drive chain
slack as shown.
4. If the drive chain slack is inco-
rrect, adjust it as follows.
NOTE:
When checking the drive chain slack,
the chain tensioner should not be tou-
ching the drive chain.
EAU22920
To adjust the drive chain slack
1. Cotter pin
2. Axle nut
3. Locknut
4. Drive chain slack adjusting bolt
5. Alignment marks
1. Axle nut
2. Locknut
3. Drive chain slack adjusting bolt
4. Alignment marks
1
2
4 3
b
a
12
3
4
5a
b
Drive chain slack:
20 ~ 25 mm (0.787 ~ 0.984 in)
16
PERIODIC MAINTENANCE AND MINOR REPAIR
6-21
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 21