2008 SKODA SUPERB phone

Communication141
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
„List
„Surname
„First name
„Own no. send - the possibility to suppress one's own number on the unit called
„Signal settings
„Ring tone
„Volume
„Phone settings
„Select operator
„Automatic
„Manual
„Off time
„+ 5 Minutes
„- 5 Minutes
„GPRS - Setting of the access point of the user
„Switch off ph. - switching off the telephone unit (telephone remains
connected)
Back
Return in the main menu of the information display.
Voice commands
Voice commands for operating the telephone control unit Other possible commands
Select number
–Press the button PTT
⇒page 139, fig. 142 .
– Give the command DIAL NUMBER after the signal tone.
After giving this command, the system re quests the entry of a telephone number.
The telephone number can be entered as an interconnected spoken row of digits
Voice commandActivity
HELPAfter this command the sy stem repeats all possible
commands.
LO N G D I A LO G U EHelp is not reduced (s uitable for beginners).
SHORT DIALOGUEHelp is clearly reduced (good operating knowledge
provided).
CALL NAMEAfter this command a name can be entered which
establishes a connection to the requested partner
⇒page 144.
DIAL NUMBERAfter this command a telephone number can be
entered which establishes a connection to the
requested partner ⇒page 142.
REDIALAfter this command the system selects the last
selected number ⇒page 143.
Voice commandActivity
CALLS (SELECT)The telephone number is selected.
REPEATThe entered name or the digits are repeated. Then
the system requests with voice response “ please
proceed ” the entry of further digits or commands.
BACK
The entered name or the last entered order of digits is
erased. Previously entered groups of digits are
repeated. Then the system requests with voice
response “ and proceed? ” the entry of further digits
or commands.
DELETEAll entered digits are erased.
CANCELThe dialogue is ended.
Voice commandActivity
A1
NKO B6 20.book Page 141 Wednesday, March 26, 2008 3:15 PM

Communication
142
(complete number), in the form of order of digits (separation through a brief voice
pause) or through individually spoken digits. After each order of digits (separation
through brief voice pause) the detected digits are repeated.
The digits zero to nine are permitted. The system detects no continuous digit
combinations such as twenty-three, but only individually spoken digits (two, three).
You can enter the selected number in rand om digital blocks or as a whole number
at once. We recommend to enter the sele cted number in digital blocks to each
three digits.
If you enter more than 20 di gits, the system announces: “ The number is too long”.
For an international call you can enter the symbol instead of the two zeros at the
beginning of the selected number Plus (+).
Example when entering a telephone number
You can interrupt the dialogue at any time by pressing the PTT button or with the
voice command CANCEL.Repeat last call
– Press the button PTT ⇒ page 139, fig. 142.
– Give the command REDIAL after the signal tone.
After giving this command, the last number selected via voice input is selected
again.
Example of redial
You can interrupt the dialogue at any time by pressing the PTT button or with the
voice command CANCEL .
Phone voice phonebook*
Store name
– Press the button .
– In the menu telephone, select the menu point Phone book and in this
menu point, select a contact of which you want to record a voice
recording and confirm with the handwheel .
– Select the menu point Record and afterwards Recording.
– The system gives the command “ Store name, name please”.
– Pronounce the name, e. g “Name XYZ”, the system repeats the name.
– The system gives the notice “ Name stored”.
In the case that the system does not und erstand the spoken name, it gives the
notice “Pardo n? ”, “Please repeat the name ”, “The name is too short ” or “The
name is too long ”.
Voice commandAnnouncement
DIAL NUMBER“The number please ”
e.g. SIX ZERO THREE“Six zero three ”
“And proceed? ”
e.g. ONE TWO THREE FOUR“One, two, three, four ”
“And proceed? ”
z. B. FIVE SIX“Five, six ”
CALLS (SELECT)“The number is being dialed ”
If no entry is put in, the following a nnouncement is made after about 5 seconds.
“Possible commands are: dial,
repeat, back, or delete ”
Voice commandAnnouncement
REDIAL“The number is being dialed”
A1
A4
NKO B6 20.book Page 142 Wednesday, March 26, 2008 3:15 PM

Communication143
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
In the phone voice phonebook up to 15 entries can be stored.
For similar names additional information (e.g. first names) should be stored.
Voice commands for operating the phone voice phone book
Example for storing the recordin
g in the phone voice phonebook
You can interrupt the dialogue at any time by pressing the PTT button or with the
voice command CANCEL.
Select name
– Press the button PTT ⇒page 139, fig. 142 .
– Give the command CALL NAME after the signal tone.
After giving this command, the system requ ests the entry of the name to be called. Example for the selection of a name
In the case that the list is empty, the message “
The name list is empty.” sounds.
If the system does not recognize the name called, it asks you to repeat using the
command “ Pardon?”. If the system has not recognized the name to be called after
repeating, the message sounds “ The name does not exist. You receive the curren
name list with LISTEN TO ALL THE NAMES. ”.
You can interrupt the dialogue at any time by pressing the PTT button or with the
voice command CANCEL.
Listening-in to the voice phonebook
– Press the PTT button.
– Give the command LISTEN TO ALL THE NAMES after the signal tone.
After giving this command, all voice record ings are replayed from the list of the
control unit. By pressing the PTT button when announcing the desired name, the
corresponding telephone number is be ing dialed; the system answers: “Call set-
up ”.
Example for the selection of a name
In the case that the list is empty, the system announces “ The name list is empty.”.
You can interrupt the dialogue at any time by pressing the PTT button or with the
voice command CANCEL.
Voice commandActivity
LISTEN TO ALL THE
NAMESAfter this command the cont rol unit repeats all stored
names.
DELETE NAMEAfter this command, you can enter a name which you
would like to erase from the internal phone voice
phonebook.
DELETE ALL NAMESAfter this command, you can erase the complete list
of the stored names.
Voice commandAnnouncement
STORE NAME“ The name please ”
Name XYZ“Please repeat the name ”
Name XYZ“The name XYZ is stored ”
A1
Voice commandAnnouncement
CALL NAME“Call name ”
Name XYZ“Do you want to call XYZ? ”
CALLS (SELECT)“The name is being dialed ”
Voice commandAnnouncement
LISTEN TO ALL THE NAMES“Interrupt using the voice button ”
NKO B6 20.book Page 143 Wednesday, March 26, 2008 3:15 PM

Communication
144
After replaying the complete list, the system announces “ End of name list”.
Erase entries out of the phone voice phonebook
– Press the PTT button.
– Give the command ERASE NAME after the signal tone.
After giving this command, there is the possibility to erase a stored entry in the
phone voice phonebook.
Example for erasing an entry out of the phone voice phonebook
You can interrupt the dialogue at any time by pressing the PTT button or with the
voice command CANCEL.
If the user answers with NO, the system answers with “ Cancel” and the dialogue is
ended.
Erase the complete phone voice phonebook
– Press the PTT button.
– Give the command DELETE PHONEBOOK after the signal tone.
After giving this command, there is the possibility to erase the complete phone
voice phonebook. Example for erasing the complete phone voice phonebook
You can interrupt the dialogue
at any time by pressing the PTT button or with the
voice command CANCEL .
If the user answers with NO, the system answers with “ Cancel” and the dialogue is
ended.
Mobile phones and tw o-way radio systems
The installation of a mobile phone and tw o-way radio system in a vehicle should
only be carried out by a Škoda Dealer.
Škoda Auto a.s. permits the operation of mobile phones and two-way radio
systems with a professionally installed external aerial and a maximum transmission
power of up to 10 watts.
Our specialist garage is also happy to inform you about the possibilities available
for installing and operating mobile teleph ones and radio transmitters which have
an output greater than 10 watts. The Škoda Service Partners can provide you with
details about the technical possibilities fo r retrofitting of mobile telephones and
radio transmitters.
Operation of mobile phones or two-way radio systems may interfere with func-
tioning of the electronic systems of your vehicle. The reasons for this may be:
•no external aerial
•external aerial incorrectly installed
•transmission power greater than 10 watts.
You should also be aware of the fact that only an external aerial makes it possible
to achieve the optimal range of such equipment.
Voice commandAnnouncement
DELETE NAME“ The name please ”
Name XYZ“Do you want to erase XYZ? ”
YES“The name is deleted ”
Voice commandAnnouncement
DELETE ALL NAMES“Do you want to delete all the
names? ”
YES“Are you sure? ”
YES“All the names are deleted ”
NKO B6 20.book Page 144 Wednesday, March 26, 2008 3:15 PM

Communication145
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
WARNING
•If a mobile phone or two-way radio sy stem is operated inside the vehicle
without using an external aerial, or wi th an external aerial which has been
incorrectly installed, the result can be excessive electromagnetic fields
which may cause harm to your health.
•Please concentrate fully at all times on your driving!
•You must not install two-way radio systems, mobile phones or mounts
on the covers of the airbags or within the immediate deployment range of
airbags. This might result in injuries to the occupants in the event of an acci-
dent.
Note
Please also refer to the operating instructions of the mobile phones and two-way
radio systems.
Input AUX-IN
The input for external audio sources AUX- IN is located below the armrest of the
front seat and is marked with  This input serves for connecting external audio
sources (e.g. portable mp3 player) to the your radio system. The equipment AUX-
IN can only be used in combination with a radio or navigation system installed in
the factory. The description on how to oper ate AUX-IN can be found in the relevant
operating instructions of the radio or the navigation system.
Note
•If an external audio source is connected via AUX-IN, which has a separate
power supply, this can lead to an interfer ence of the audio signals. It depends on
the properties of the adapter.
•The loudspeakers in the vehicle are matched to a power output of 30 W.
CD changer*
The CD changer for the radio and navigation system is located in the right
side compartment of the luggage compartment.
Loading a CD
– Touch the button and guide the CD (compact disc) into the CD-
case . The CD is automatically loaded onto the next free position in
the CD-changer. The LED in the corresponding button stops
flashing.
Loading all CDs
– Hold the button pressed and guide all CDs one after the other into the CD-case . The LEDs in the bu ttons are no longer flashing.
Loading a CD to one definite position
– Touch button . The LEDs in the buttons light up at the memory spaces, which are already assigned and flash in the case of free
memory spaces.
– Touch the desired button and guide the CD into the CD-case .
Fig. 144 The CD changer
AC
AB
AD
AC
ABAD
ACAD
ADAB
NKO B6 20.book Page 145 Wednesday, March 26, 2008 3:15 PM

Passive Safety
150
Before setting off
The driver is always fully respon sible for his occupants and for the
operating safety of the vehicle.
For your own safety and the safety of the people travelling with you, please pay
attention to the following points before setting off.
•Ensure that the lighting and the turn signal system are functioning properly.
•Inspect the tyre inflation pressure.
•Ensure that all the windows offer a good visibility to the outside.
•Safely attach the items of luggage ⇒page 78, “Loading the luggage compart-
ment”.
•Ensure that no objects can obstruct the pedal.
•Adjust the mirror, the front seat and the head restraint to match your body size.
•Point out to your occupants that the head restraints must be adjusted to match
their body size.
•Protect the children in suitable child se ats with correctly fastened seat belts
⇒ page 171, “Transporting children safely”.
•Adopt the correct seated position ⇒page 150, “Correct seated position”. Also
inform your occupants to adopt the correct seated position.
•Fasten the seat belt correctly. Also inform your occupants to properly fasten the
seat belts ⇒page 156, “How are seat belts correctly fastened?”.
What influences the driving safety?
The driving safety is primarily dete rmined by the style of driving and
the personal behaviour of all the occupants.
The driver is fully responsible for himself and his occupants. If your driving safety is
effected, you place yourself and the oncomi ng traffic at risk. Please refer to the
following guidelines.
•Do not get distracted from concentrating on the traffic situation, e.g. by your
occupants or mobile phone calls.
•Never drive when your driving ability is impaired, e.g. through medication,
alcohol, drugs.
•Keep to the traffic regulations and the permissible speed limit.
•Adjust the driving speed at all times to the road condition as well as to the traffic
and weather conditions.
•Take regular breaks on long journe ys - at the latest every two hours.
Correct seated position
Correct seated position for the driver
Correct seated position for the driver is important for safe and
relaxed driving.
Fig. 145 The correct distance
of the driver from the
steering wheel
NKO B6 20.book Page 150 Wednesday, March 26, 2008 3:15 PM

Airbag system163
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Important safety information regarding the front airbag system
Correct use of the airbag system considerably reduces the risk of
injury!
WARNING
•Never transport children on the front seat of a vehicle without using a
proper restraint system. If airbags are deployed in the event of an accident,
the child might suffer severe or even fatal injuries!
•For the driver and front passenger it is important to maintain a distance
of at least 25 cm from the steering wheel or dash panel ⇒fig. 157 . Not main-
taining this minimum distance will mean that the airbag system will not be
able to properly protect you - hazard! The front seats and the head restraints
must always also be correctly adjusted to match the body size of the occu-
pant.
•It is essential to always switch off ⇒page 168, “Deactivating an airbag”
the front passenger airbag when attach ing a child safety seat on the front
passenger seat where the child is seated with its back facing in direction of
travel (in some countries also when the ch ild is facing the direction of travel).
If this is not done, there is a risk of the child suffering severe or even fatal
injuries if the front passenger airbag is deployed. In certain countries
national legal provisions also requir e that the side or head passenger
airbags be deactivated. When transporting a child on the front passenger seat, please comply with the appropriate national regulations regarding the
use of child safety seats.
•There must not by any further persons, animals or objects positioned
between the front seated occupants and the deployment area of the airbag.
•The steering wheel and the surface of the airbag module in the dash
panel on the passenger side must not be stuck onto, covered or modified in
any other way. These parts should only be cleaned with a dry cloth or a cloth
moistened with water. No objects such as cup holders, mobile phone
mounts, etc. may be attached to the covers of the airbag modules or be
located within the immediate area.
•No modifications of any kind may be made to parts of the airbag system.
Any work on the airbag system includ ing installing and removing system
components because of other repair work (e.g. removing the steering
wheel) must only be carried out by a specialist garage.
•Never carry out changes on the front bumper or on the body.
•Never place any objects on the surface of the front passenger airbag in
the dash panel.
Fig. 157 Safe distance to
steering wheel
WARNING (continued)
NKO B6 20.book Page 163 Wednesday, March 26, 2008 3:15 PM

Breakdown assistance
236
– Reinstall the full wheel trim/wheel cap after removing the adapter or place the cap onto the safety wheel bolt.
– Have the tightening torque checked w i t h a t o rq u e w re n c h a s s o o n a s
possible. Steel and light alloy wheels must be tightened to a tightening
torque of 120 Nm.
The safety wheel bolts on vehicles fitted with them (one safety wheel bolt per
wheel) can only be loosened or tigh ten up by using the adapter provided.
It is meaningful to note the code numbe r hammered into the rear side of the
adapter or the rear side of the safety wheel bolts. You can obtain a replacement
adapter from a Škoda Service Partner, if necessary, by quoting this number.
We recommend that you always carry the adapter for the wheel bolts with you in
the vehicle. It should be st owed in the vehicle tool kit.
Caution
Damage can occur to the adapter and safety wheel bolt if the safety wheel bolt is
tightened up too much.
Note
The set of safety wheel bolts can be obtained from a Škoda Service Partner.
Jump-starting
Initial steps
You can use the battery of another vehicl e for jump-starting yours if the engine
does not start because the battery on your vehicle is flat. You will require jump-start
cables for this purpose.
Both batteries must have a rated voltage of 12 V. The capacity (Ah) of the battery
supplying the power must not be significa ntly less than the capacity of the
discharged battery in your vehicle. Jump-start cables
Only use jump-start cables which have an
adequately large cross-section and insu-
lated terminal clamps. Please pay attent ion to the manufacturer's instructions.
Positive cable - colour coding in the majority of cases red.
Negative cable - colour coding in the majority of cases black.
WARNING
•A discharged battery may already freeze at temperatures just below 0°C.
In case of frozen battery carry out no jump-starting - risk of explosion!
•Please pay attention to the warning instructions relating to working in
the engine compartment ⇒page 209, “Working in the engine compart-
ment”.
Note
•There must not be any contact between the two vehicles otherwise current may
flow as soon as the negative terminals are connected.
•The discharged battery must be properly connected to the system of the
vehicle.
•Switch off any mobile phone, pay attent ion to the instructions for use of the
mobile phone in such a situation.
•We recommend purchasing jump-start cabl es from Škoda Service Partners as a
Škoda original accessory or from retailers who sell branded batteries.
NKO B6 20.book Page 236 Wednesday, March 26, 2008 3:15 PM