2008 RENAULT SCENIC lights

MULTIMEDIA
Fault finding - Introduction
86C
86C-2V5 MR-372-J84-86C050$052.mif
186C
ITS
Program No.: 0020
Vdiag No.: 04MULTIMEDIA
Fault finding - Introduction
1. SCOPE OF THIS DOCUMENT
This document presents the fault finding procedure applicable to all computers with the following specifications:
2. PREREQUISITES FOR FAULT FINDING
Documentation type
Fault finding procedures (this document):
–Assisted fault finding (integrated into the diagnostic tool), Dialogys.
Wiring Diagrams:
–Visu-Schéma (CD-ROM), paper.
Type of diagnostic tools
–CLIP + multiplex line sensor
Special tooling required
3. REMINDERS
Procedure
To run fault finding on the vehicle's computers, switch on the ignition in fault finding mode (forced + after ignition
feed).
Proceed as follows:
–vehicle card in reader,
–press and hold start button (longer than 5 seconds) with start-up conditions not fulfilled,
–connect the diagnostic tool and perform the required operations.
To cut off the + after ignition feed, proceed as follows:
–disconnect the diagnostic tool,
–press the Start button twice briefly (less than 3 seconds),
–check that the computer warning lights on the instrument panel have gone out to confirm that the + after ignition
feed has been cut off. Vehicle: Scenic II ph2
Function concerned: Navigation, integrated
hands-free telephone, receiver, CD playerName of computer: ITS
Program No.: 0020
Vdiag No.: 04
Special tooling required
Multimeter
Elé. 1681Universal bornier
Note:
The left-hand and right-hand xenon bulb computers are powered when the dipped headlights are lit.
Fault finding can only be run after the ignition is switched on in fault finding mode (forced + after ignition feed)
and the dipped headlights are lit.
TDB_V04_PRELIITSJ84ph2V1.0
MR-372-J84-86C050$052.mif

MULTIMEDIA
Fault finding - Conformity check
86C
86C - 24V5 MR-372-J84-86C050$520.mif
ITS
Program no.: 0020
Vdiag No.: 04MULTIMEDIA
Fault finding - Conformity check
MAIN SCREEN
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application conditions: Engine stopped, + after ignition feed switched on.
Order FunctionParameter or Status
Check or Action Display and Notes Fault finding
1Night-time
lightingET003:+ 12 V side
lights feedON
OFFIn the event of a fault, consult
the interpretation of status
ET003 + 12 V side lights
feed.
2Vehicle speed PR002:Vehicle speed0 mph
Carry out a road test to
obtain a variation.In the event of a fault, consult
the interpretation of
parameter PR002 Vehicle
speed.
3Reverse gear ET024:Reverse gear
engagedYES
NOIn the event of a fault, consult
the interpretation of status
ET024 Reverse gear
engaged.
4CD multi-
changerPR005:Number of CDs
in the multi-
changer0, 1, 2, 3, 4, 5 or 6None
ITS_V04_CCONFITSJ84ph2V1.0
MR-372-J84-86C050$520.mif

MULTIMEDIA
Fault finding - Status summary table
86C
86C - 28V5 MR-372-J84-86C050$572.mif
ITS
Program no.: 0020
Vdiag No.: 04MULTIMEDIA
Fault finding - Status summary table
Tool status Diagnostic tool title
ET003+ 12 V side lights feed
ET006+ button
ET007- button
ET009Upper button
ET010Lower button
ET017Communication connection button
ET018Wheel action
ET024Reverse gear engaged
ET034MODE button
ITSJ84ph2V1.0
MR-372-J84-86C050$572.mif

MULTIMEDIA
Fault finding - Interpretation of statuses
86C
86C - 29V5 MR-372-J84-86C050$624.mif
ITS
Program no.: 0020
Vdiag No.: 04MULTIMEDIA
Fault finding - Interpretation of statuses
ET003
+ 12 V SIDE LIGHTS FEED
NOTESVisually check that the side lights are working. Carry out fault finding on the steering
column switches and the side lights.
Use the Wiring Diagrams Technical Note, Scenic II.
Check the condition of the 7.5 A fuse in the engine compartment connection unit (component code 1337).
Check the condition and connection of the navigation central control connectors (component code 1657) and of
the CD changer (component code 1272) (broken, bent tabs).
If the connectors are faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connectors; otherwise, replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the LPG connection between
components 1337, 1272 and 1657.
If the connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
If the fault is still present, contact the Techline.
AFTER REPAIRRepeat the conformity check from the start.
ITS_V04_ET003ITSJ84ph2V1.0
MR-372-J84-86C050$624.mif