2008 RENAULT SCENIC air condition

MULTIMEDIA
Fault finding - Interpretation of commands
86C
86C - 42V5 MR-372-J84-86C050$832.mif
ITS
Program no.: 0020
Vdiag No.: 04
AC009
MICROPHONE TEST
NOTESThere must be no present or stored faults.
Use the Wiring Diagrams Technical Note, Scenic II.
Apply this procedure if the Faulty connection message appears when these commands are activated.
Check the condition and connection of the microphone connector (component code 789) and of the navigation
computer 40-track connector (component code 662) (broken, oxidised, bent tabs).
If the connectors are faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connectors; otherwise, replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
●connection code 107J,
●connection code 107G,
●connection code 107F,
between components 789 and 662.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
If the checks reveal no faults but the microphone does not work, replace component 789.
AFTER REPAIRCarry out another fault finding check on the system.
ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Fault finding charts
86C
86C-45V5 MR-372-J84-86C050$936.mif
ITS
Program No.: 0020
Vdiag No.: 04MULTIMEDIA
Fault finding - Fault finding charts
ALP 1 No dialogue with the computer
NOTESSwitch on the + after ignition feed to enter fault finding mode with the computer.
Use the Wiring Diagrams Technical Note, Scenic II.
Check the condition and connection of the battery connections.
Check the condition of the fuses.
Check the battery voltage.
Try the diagnostic tool on another vehicle.
Check:
–the connection between the diagnostic tool and the diagnostic sensor (wiring in good condition),
–the connection between the diagnostic sensor and the diagnostic socket (wiring in good condition).
Check for + 12 V on the 34HU connection of the navigation computer (component code 662).
Check for + 12 V battery feed on connection BP32, for + 12 V after ignition feed on connection AP43 and for
an earth on the NAM connection and on the MAM connection of the diagnostic socket (component code 225).
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
Check for + 12 V battery feed on connection BCP3 and an earth on connection MX of component 662.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
Disconnect the 32-track connector of component 662 and the connector of component 1657 to check
the insulation, continuity and absence of interference resistance of the following connections:
●connection code 34GA,
●connection code 34DZ,
between components 662 and 1657;
●connection code 107X,
●connection code 107W,
between components 1657 and 225;
●connection code BCP3,
between components 662 and 260;
●connection code MX,
between component 662 and earth MX.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
ITS_V04_ALP1ITSJ84ph2V1.0
MR-372-J84-86C050$936.mif

MULTIMEDIA
Fault finding - Fault finding charts
86C
86C-46V5 MR-372-J84-86C050$936.mif
ITS
Program No.: 0020
Vdiag No.: 04
ALP 2 the screen stays black
NOTESOnly check the customer complaint after performing a full check with the
diagnostic tool.
Check that the customer is using the navigation system correctly.
Use the Wiring Diagrams Technical Note, Scenic II.
Check that the display has not been deactivated.
Press the LIGHT button on the central control for 2 seconds to reactivate the display.
To check the supply to the display, switch on
the ignition, switch on the navigation system
and eject the navigation DVD.
Has the DVD been removed?
YES
Check for + 12 V on connection BCP3 and an earth
on connection MAN of the display (component
code 1127).
Are these tests correct?
YES
Check the insulation, continuity and the absence
of interference resistance of connection 34HU
between components 1127 and 1272.
–If the connection is correct, replace the display.
–If any connection is faulty and if there is a repair
method (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for
repair), repair the wiring; otherwise, replace
the wiring.
NOCheck the condition of the supply fuse
(20A) (component code 260).
Has the fault disappeared?
YES NO
Check for + 12 V on
connection BCP3 and an
earth on connection MX of
the navigation computer
(component code 662).
NOCheck the insulation,
continuity and the absence
of interference resistance
of connections 34DB, 34DC
et 34DD between
components 662 and 1127.
YES Are these checks correct?
NO
If any connection is faulty and if there is a repair
method (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair),
repair the wiring; otherwise, replace the wiring.
End of fault finding.
Contact Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
ITS_V04_ALP2ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Fault finding charts
86C
86C-48V5 MR-372-J84-86C050$936.mif
ITS
Program No.: 0020
Vdiag No.: 04
ALP 3
CONTINUED
Check the condition and the connection of the 32-track connector of the receiver (component code 261), of
the navigation central control connector (component code 1657) and of the 40-track connector of the navigation
computer (component code 662) (tabs bent, broken, oxidised, etc.).
If the connectors are faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connectors; otherwise, replace the wiring.
Check the insulation, continuity and absence of interference resistance on connections TB27, 34HD and 34HG
between components 662 and 261.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
Has the fault disappeared?
NO YES
Contact Techline.
End of fault finding.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Fault finding charts
86C
86C-50V5 MR-372-J84-86C050$936.mif
If any connection is faulty and if there is a repair
method (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair),
repair the wiring; otherwise, replace the wiring.
ITS
Program No.: 0020
Vdiag No.: 04
ALP 5 Poor satellite reception
NOTESOnly check the customer complaint after performing a full check with the diagnostic
tool.
Check that the customer is using the navigation system correctly.
Ensure there are no present or stored faults.
Use the Wiring Diagrams Technical Note, Scenic II.
What colour is the GPS pictogram?
Green
The system operates normally.
Yellow
or
GreyPositioning is imprecise (yellow) or
impossible (grey) in the following areas:
forests, tunnels, valleys, under bridges
and in stormy weather.
Carry out a system test in an open area.
Check the condition and cleanliness of the
GPS aerial.
Check the insulation, continuity and
the absence of interference resistance
of connections 46CB and TB15 between
components 662 and 886.
NO Did it pass the tests?
YES
If the fault is still present, replace the GPS
aerial.
If the satellite reception is poor, contact
the Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
ITS_V04_ALP5ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Fault finding charts
86C
86C-51V5 MR-372-J84-86C050$936.mif
ITS
Program No.: 0020
Vdiag No.: 04
ALP 6The radio does not switch on automatically or switches off after
20 minutes
NOTESOnly check the customer complaint after performing a full check with the diagnostic
tool.
Check that the customer is using the navigation system correctly.
Use the Wiring Diagrams Technical Note, Scenic II.
The navigation system does not receive the multimedia wake-up signal when the + after ignition feed is
switched on.
Check the condition of the CD changer fuses (component code 1272).
Has the fault disappeared?
NO YES
On pressing the CD changer on/off button, check for
the multimedia wake-up signal on connection 34HU
on the radio's blue connector (component
code 261).
Is the check result correct?
NO
Check the insulation, continuity and the absence
of interference resistance of connection 34HU
between components 1272, 261, 1657, 1127
and 662.
If any connection is faulty and if there is a repair
method (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair),
repair the wiring; otherwise, replace the wiring.
Has the fault disappeared?
NO YES
End of fault finding.
End of fault finding.
YESCheck for + 12 V (+ battery feed) on
connection BCP3 of the component 261
black connector.
Is the check result correct?
NO YES
Check the insulation, continuity and the
absence of interference resistance of
connection BCP3 between components 261
and 260.
If any connection is faulty and if there is a repair
method (see Technical Note 6015A,
Repairing electrical wiring, Wiring:
Precautions for repair), repair the wiring;
otherwise, replace the wiring.
Has the fault disappeared?
YES NO
AFTER REPAIRCarry out a complete check with the diagnostic tool.
ITS_V04_ALP6ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Fault finding charts
86C
86C-54V5 MR-372-J84-86C050$936.mif
ITS
Program No.: 0020
Vdiag No.: 04
ALP 8 The volume does not change with a change in vehicle speed
NOTESOnly check the customer complaint after performing a full check with the diagnostic
tool.
Check that the customer is using the navigation system correctly.
Use the Wiring Diagrams Technical Note, Scenic II.
Check that volume according to speed function has
been activated.
Press the SET button and select the volume
correction menu.
Is the volume according to speed function
active?
YES
Carry out fault finding on the ABS/ESP (see 38C,
Anti-lock braking system).
Check the condition and connection of the receiver 32-track connector (component code 261) and of the navigation
computer 32-track connector (component code 662). If the connectors are faulty and if there is a repair method
(see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for repair), repair
the connectors; otherwise, replace the wiring.
Check the insulation, continuity and the absence of interference resistance of the connection 47F between
components 261 and 662. If the connection is faulty and if there is a repair method (see Technical Note 6015A,
Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
NOActivate this function.
Carry out a road test and check that
the volume varies as the vehicle speed
varies.
Does the volume vary?
NO YES
End of fault finding.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
ITS_V04_ALP8ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Fault finding charts
86C
86C-55V5 MR-372-J84-86C050$936.mif
ITS
Program No.: 0020
Vdiag No.: 04
ALP 8
CONTINUED
Check the condition and connection of the ABS computer connector (component code 118 or 1094). If the
connectors are faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connectors; otherwise, replace the wiring.
If no fault is found with the ABS system, check the insulation, continuity and the absence of interference
resistance of connection 47F between components 261 and 118 or 1094 according to the vehicle's equipment
level.
If the connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
ITSJ84ph2V1.0