2008 RENAULT SCENIC air condition

MULTIMEDIA
Fault finding - Fault finding charts
86C
86C-56V5 MR-372-J84-86C050$936.mif
ITS
Program No.: 0020
Vdiag No.: 04
ALP 9 Poor radio reception
NOTESOnly check the customer complaint after performing a full check with the diagnostic
tool.
Use the Wiring Diagrams Technical Note, Scenic II.
Check the condition and connection of the 32-track connector and the aerial connector on the radio
(component code 886).
If the connectors are faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connectors; otherwise, replace the wiring.
Check the insulation, continuity and the absence of interference resistance of the following connections:
●connection code 34AM,
●connection code 34AN,
●connection code TB13,
between components 261 and 886.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
ITS_V04_ALP9ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Fault finding charts
86C
86C-57V5 MR-372-J84-86C050$936.mif
ITS
Program No.: 0020
Vdiag No.: 04
ALP 10 The CD changer does not work
NOTESOnly check the customer complaint after performing a full check with the diagnostic
tool.
Check that the customer is using the system properly.
Use the Wiring Diagrams Technical Note, Scenic II.
Check the condition of the 15 A fuses (+ accessories
feed) on component 260 and 7.5 A (+ after ignition
feed) on component 1337.
Are the fuses in good condition?
YES
Check the condition and connection of the CD multi-changer connector (component code 1272).
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Has the fault disappeared?
NO YES
Disconnect the connector from component 1272,
check for + battery feed on connection BCP3, for
+ accessories feed on connection SP2 and for
+ after ignition feed on connection AP43 of
the component 1272 connector.
Also check that the earth on connection MAN is
perfect.
Did it pass the tests?
NO YES
NOReplace the fuses.
End of fault finding.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
ITS_V04_ALP10ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Fault finding charts
86C
86C-67V5 MR-372-J84-86C050$936.mif
ITS
Program No.: 0020
Vdiag No.: 04
ALP 16
CONTINUED
Place the telephone close to the navigation
computer.
If the fault is still present, check the condition
and connection of the connectors on the navigation
computer and the radio.
Is the interference still present?
YES
Match up another telephone and make a call.
Is the interference still present?
YES NO
If the fault is still present, contact the
Techline.
Fault solved, end of fault finding.
Procedure for matching the communication system
and the telephone:
On the navigation and communication system:
–Press the SET button.
–Enter the telephone menu.
–Select the Bluetooth option line.
–Select the save a Bluetooth telephone line.
On the telephone:
–Enter the menu to find a Bluetooth accessory.
–In the list of found accessories, select My CAR.
–Enter the PIN code given on the vehicle's navigation
display.NOEnd of fault finding.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Fault finding charts
86C
86C-68V5 MR-372-J84-86C050$936.mif
ITS
Program No.: 0020
Vdiag No.: 04
ALP 17The person calling using the communication system cannot hear
me very well or cannot hear me at all (with Bluetooth)
NOTESOnly check the customer complaint after performing a full check with the diagnostic
tool.
Check that the customer is using the system properly.
Check that the telephone network signal is strong enough to make a call.
For information on the latest list of telephones approved by Renault and the various
operations to perform on these telephones, see Technical Note 6024A Special
features of mobile phones for the navigation and communication system.
Make a call to a fixed line.
Is the fault still present?
YES
With the engine stopped, is voice recognition of
the words Directory and Dial working?
YES
Check the condition and connection of the
connectors of the telephone support base plate,
the navigation computer and the radio.
Match up another telephone and make a call.
Is the fault still present?
YES NO
If the fault is still present, contact the
Techline.
NOThe fault is linked to the number the
customer is calling or to a localised lack of
network availability.
Procedure for matching the communication system and the
telephone:
On the navigation and communication system:
–Press the SET button.
–Enter the telephone menu.
–Select the Bluetooth option line.
–Select the save a Bluetooth telephone line.
On the telephone:
–Enter the menu to find a Bluetooth accessory.
–In the list of found accessories, select My CAR.
–Enter the PIN code given on the vehicle's navigation
display.NOCheck the condition and connection of
the microphone connector.
Check that the microphone part number is
correct. If not, replace the microphone.
The fault is probably caused by the telephone. Ask the customer to carry
out a fault finding procedure on the telephone.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
ITS_V04_ALP17ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Fault finding charts
86C
86C-69V5 MR-372-J84-86C050$936.mif
ITS
Program No.: 0020
Vdiag No.: 04
ALP 18 Voice recognition is not working
NOTESOnly check the customer complaint after performing a full check with the diagnostic
tool.
Check that the customer is using the system properly.
Use the Wiring Diagrams Technical Note, Scenic II.
With the engine stopped, then at 30 mph
(50 km/h) does voice recognition of the words
Directory and Dial work?
YES
The customer needs to use voice recognition
intensively for 2 weeks so that the voice recognition
system can learn to recognise his voice.
If the fault is still present, contact the Techline.
NOCheck the condition and connection of
the microphone connector
(component code 789).
Check that the microphone part number is
correct. If not, replace the microphone.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
ITS_V04_ALP18ITSJ84ph2V1.0