2008 RENAULT SCENIC Engine Compartment Connection Unit Workshop Manual

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87G
87G-57V7 MR-372-J84-87G050$440.mif
UPC
Vdiag No.: 48, 4C
KEYLESS VEHICLE
SUB-FUNCTION: STARTING
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application conditions: engine stopped, + after ignition feed on.
FunctionParameter or Status
Check or ActionDisplay and Notes Fault finding
Reverse gearET004:Reverse gear
engagedYES
NOIn the event of a fault, refer to the
interpretation of status ET004.
Manual gearbox
lever positionET005:Manual gearbox
lever positionNOT IN NEUTRAL
NEUTRALNormal statuses.
UNAVAILABLE
INVALIDIn the event of a fault, refer to the
interpretation of status ET004.
Starting
conditions metET010:Starting
conditions metSTATUS 1
STATUS 2
STATUS 3In the event of a fault, consult the
interpretation for status ET010.
YESNormal status.
+ 12 V after
ignition feed
relay controlET003:+ 12 V after
ignition feed relay
control INACTIVE
ACTIVEIn the event of a fault, consult the
interpretation of fault DF032.

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87G
87G-58V7 MR-372-J84-87G050$440.mif
UPC
Vdiag No.: 48, 4C
FUNCTION: AIR CONDITIONING
SUB-FUNCTION: HEATING
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application conditions: engine stopped, + after ignition feed on.
FunctionParameter or Status
Check or ActionDisplay and Notes Fault finding
Alternator chargePR010:Alternator charge0 < X < 99.6%
With the engine running,
activate the heated rear
screen and check that the
value increases.In the event of a fault, consult
the interpretation of
parameter PR010.
Rear screen de-
icerAC011:Rear screen de-
icerThis command supplies
the rear screen and door
mirror heating resistors, if
fitted to the vehicle.
They should be warm. In the event of a fault, apply the
procedure for dealing with
command AC011.

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87G
87G-59V7 MR-372-J84-87G050$440.mif
UPC
Vdiag No.: 48, 4C
FUNCTION: AIR CONDITIONING
SUB-FUNCTION: COLD LOOP
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application conditions: engine stopped, + after ignition feed on.
FunctionParameter or Status
Check or ActionDisplay and Notes Fault finding
Compressor
controlAC008:Compressor
controlYou should be able to hear
the compressor clutch
(stops the motor running).In the event of a fault, apply the
procedure for dealing with
command AC008.
Fan assemblyAC009:Low-speed fan
assemblyThis command is used to
activate the fan assembly
at low speed.In the event of a fault, apply the
procedure for dealing with
command AC009.
AC010:High-speed fan
assemblyThis command is used to
activate the engine cooling
fan at high speed.In the event of a fault, apply the
procedure for dealing with
command AC010.
Low-speed
engine fan
assembly relay
controlET014:Low-speed
engine fan
assembly relay
controlINACTIVE
ACTIVEIn the event of a fault, consult
the interpretation for status
ET014.
High-speed
engine fan
assembly relay
controlET013:High-speed
engine fan
assembly relay
controlINACTIVE
ACTIVEIn the event of a fault, consult
the interpretation for status
ET013.

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87G
87G-60V7 MR-372-J84-87G050$440.mif
UPC
Vdiag No.: 48, 4C
FUNCTION: WIPING
SUB-FUNCTION: WIPER POWER
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application conditions: engine stopped, + after ignition feed on.
FunctionParameter or Status
Check or ActionDisplay and Notes Fault finding
WiperAC005:Low-speed
windscreen wiperThis command is used to
activate the windscreen
wiper motor at low
speed.In the event of a fault, apply the
procedure for dealing with
commands AC005 and AC006.
AC006:High-speed
windscreen wiperThis command is used to
activate the windscreen
wiper motor at high
speed.
Windscreen
wiper protectionET002:Windscreen
wiper protectionINACTIVEIn the event of a fault, refer to the
interpretation for status ET002.
Windscreen
wiper park
positionET018:Windscreen
wiper park
positionPRESENT (if the wiper
is not active)
ABSENTIn the event of a fault, refer to the
interpretation of status ET018.
Headlight
washerAC013:Headlight washer
relayThis command is used to
activate the headlight
washers relay on the
right and left-hand side
alternately.In the event of a fault, apply the
procedure for dealing with
command AC013.

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87G
87G-61V7 MR-372-J84-87G050$440.mif
UPC
Vdiag No.: 48, 4C
FUNCTION: LIGHTING
SUB-FUNCTION: LIGHTING POWER
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application conditions: engine stopped, + after ignition feed on.
FunctionParameter or Status
Check or ActionDisplay and Notes Fault finding
Side lightsAC003:Side lightsThis command
switches on the side
lights.In the event of a fault, apply the
procedure for dealing with
command AC003.
Dipped
headlightsAC002:Dipped
headlightsThis command
switches on the dipped
beam headlights.In the event of a fault, apply the
procedure for dealing with
command AC002.
Main beam
headlightsAC001:Main beam
headlightsThis command
switches on the main
beam headlights.In the event of a fault, apply the
procedure for dealing with
command AC001.
Front fog lightsAC004:Front fog lightsThis command
switches on the front
fog lights.In the event of a fault, apply the
procedure for dealing with
command AC004.

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87G
87G-62V7 MR-372-J84-87G050$440.mif
UPC
Vdiag No.: 48, 4C
FUNCTION: CHARGE CIRCUIT
SUB-FUNCTION: ALTERNATOR
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application conditions: engine running.
FunctionParameter or Status
Check or ActionDisplay and Notes Fault finding
Alternator faultET023:Alternator
thermal faultABSENTIn the event of a fault, consult the
interpretation of status ET023
Alternator thermal fault.
Alternator chargePR010:Alternator charge0 < X < 99.6%
Activate the heated rear
screen and check that the
value increases.Apply the procedure for PR010
Alternator charge.
Alternator
regulationAC014:Alternator
regulationRun this command with
the engine running.
When the command is
run, the Protection and
Switching Unit sets a
regulation voltage
setpoint for the alternator:
– Alternator voltage =
15 V for 30 seconds.
– Alternator voltage =
13 V for 30 seconds.Apply the procedure for dealing
with command AC014.

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87G
87G-63V7 MR-372-J84-87G050$440.mif
UPC
Vdiag No.: 48, 4C
FUNCTION: CHARGE CIRCUIT
SUB-FUNCTION: BATTERY
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application conditions: engine stopped, + after ignition feed active.
FunctionParameter or Status
Check or ActionDisplay and Notes Fault finding
VoltagesPR004:Battery voltage11 < X < 13.5 V
engine running
< 15.8 VIn the event of a fault, apply the
procedure for dealing with PR004
Battery voltage.
PR008:Battery voltage
after rest12.2 V < X <13.5 VIn the event of a fault, apply the
procedure for dealing with PR008
Battery voltage after rest.

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Status summary table87G
87G-64V7 MR-372-J84-87G050$495.mif
UPC
Vdiag No.: 48, 4CENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Status summary table
Tool status Diagnostic tool title
ET002Windscreen wiper protection
ET003+ 12 V after ignition feed relay control
ET004Reverse gear engaged
ET005Manual gearbox lever position
ET010Starting conditions met
ET013High-speed engine fan assembly relay control
ET014Low-speed engine fan assembly relay control
ET018Windscreen wiper park position
ET023Alternator thermal fault
ET027Oil pressure contact
ET062UCH request to injection or Protection and Switching Unit
MR-372-J84-87G050$495.mif