2008 RENAULT SCENIC Engine Compartment Connection Unit Workshop Manual

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87G
87G - 81V7 MR-372-J84-87G050$770.mif
UPC
Vdiag No.: 48, 4C
AC006
WINDSCREEN WIPER HIGH SPEED
NOTESSpecial notes:
Check the condition and connection of fuse 9 (25A) on the Protection and Switching
Unit. Replace it if necessary.
Make sure that status ET002 Windscreen wiper protection remains INACTIVE.
Use Wiring Diagrams Technical Note for Mégane II or Scénic II.
Check the condition and connection of the wiper motor component code 212 (tabs broken, bent or oxidised).
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check for earth connection code MAS on the wiper motor component code 212.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check for + 12 V on connection code 14L on the wiper motor whilst running the command.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the condition and connection of the Protection and Switching Unit CN connector, connection code 1337
(tabs broken, bent or oxidised).
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check the insulation, continuity and the absence of interference resistance on the following connection:
–14L, between components 1337 and 212.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact Techline.
AFTER REPAIRRepeat the conformity check from the start.

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87G
87G - 82V7 MR-372-J84-87G050$770.mif
UPC
Vdiag No.: 48, 4C
AC008
COMPRESSOR CONTROL
NOTESSpecial notes:
Activating the command with the engine running is prohibited.
Check the condition and connection of fuse 22 (10A) on the Protection and Switching
Unit.
Use Wiring Diagrams Technical Note for Mégane II or Scénic II.
Check the condition and connection of the air conditioning compressor component code 171 (tabs bent, broken
or oxidised).
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check for earth connection code MAS on the air conditioning compressor component code 171.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check for + 12 V on connection code 38R on the compressor when the command is running.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the insulation, continuity and the absence of interference resistance on the following connection:
–38R, between components 1337 and 171.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact Techline.
AFTER REPAIRRepeat the conformity check from the start.

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87G
87G - 83V7 MR-372-J84-87G050$770.mif
UPC
Vdiag No.: 48, 4C
AC009
LOW-SPEED FAN ASSEMBLY
NOTESSpecial notes:
Make sure nothing is hindering the rotation of the blades.
Use Wiring Diagrams Technical Note for Mégane II or Scénic II.
Check the condition and connection of the fan assembly connector, component code 188 (tabs broken, bent or
oxidised).
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check the condition and connection of the 6-track Protection and Switching Unit MM connector (tabs broken,
bent or oxidised).
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check for earth, connection code M of the motor-driven fan assembly, component code 188.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check for + 12 V on the motor-driven fan assembly component code 188 when the command is running.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the insulation, continuity and the absence of interference resistance on the following connection:
–49L, between components 1337 and 188.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact Techline.
AFTER REPAIRRepeat the conformity check from the start.

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87G
87G - 84V7 MR-372-J84-87G050$770.mif
UPC
Vdiag No.: 48, 4C
AC010
HIGH-SPEED FAN ASSEMBLY
NOTESSpecial notes:
Make sure nothing is hindering the rotation of the blades.
Use Wiring Diagrams Technical Note for Mégane II or Scénic II.
Check the condition and connection of the fan assembly connector, component code 188 (tabs broken, bent or
oxidised).
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check the condition and connection of the 6-track Protection and Switching Unit MM connector (tabs broken,
bent or oxidised).
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check for earth, connection code M of the motor-driven fan assembly, component code 188.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check for + 12 V on the motor-driven fan assembly component code 188 when the command is running.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the insulation, continuity and the absence of interference resistance on the following connection:
–49R, between components 1337 and 188.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact Techline.
AFTER REPAIRRepeat the conformity check from the start.

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87G
87G - 85V7 MR-372-J84-87G050$770.mif
UPC
Vdiag No.: 48, 4C
AC011
HEATED REAR SCREEN
NOTESSpecial notes:
Check the condition and connection of fuse 23 (30A) on the Protection and Switching
Unit. Replace it if necessary.
Use Wiring Diagrams Technical Note for Mégane II or Scénic II.
REAR SCREEN
Check the condition and connection of the heated rear screen component code 200 (tabs bent, broken or
oxidised).
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check that the resistance of the rear screen is neither zero nor infinity.
Check that the earth on connection code MZ of the heated rear screen component code 200 is perfect.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check for + 12 V on connection code 15LP on the rear screen when the command is running.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the condition and connection of the 6-track Protection and Switching Unit CM connector (tabs broken, bent
oxidised).
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check the insulation, continuity and the absence of interference resistance on the following connection:
–15LP, between components 1337 and 200.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact Techline.
AFTER REPAIRRepeat the conformity check from the start.

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87G
87G - 86V7 MR-372-J84-87G050$770.mif
UPC
Vdiag No.: 48, 4C
AC013
HEADLIGHT WASHER RELAY
NOTESSpecial notes:
Check the condition and connection of fuse 21 (15A) on the Protection and
Switching Unit. Replace it if necessary.
The headlight washer pump operates if the dipped headlights are lit and the
windscreen washer switch is pressed and held.
Use Wiring Diagrams Technical Note for Mégane II or Scénic II.
Check the condition and connection of the headlight washer pump component code 219 (tabs bent, broken or
oxidised).
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check the condition and connection of the Protection and Switching Unit connector (tabs bent, broken, or
oxidised).
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
To check that the pump is working properly, supply the pump's tracks directly in one direction and then the other.
If the pump does not rotate, replace it.
Check for + 12 V alternately on connection code 39C of the headlight washer pump connector.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–39A, between components 1337 and 219,
–39C, between components 1337 and 219.
If the connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact Techline.
AFTER REPAIRRepeat the conformity check from the start.

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87G
87G - 87V7 MR-372-J84-87G050$770.mif
UPC
Vdiag No.: 48, 4C
AC014
ALTERNATOR REGULATION
NOTESConditions for the application of the command:
–engine running at idling speed and warm engine,
–air conditioning off,
–check that the passenger compartment blower unit is not operating.
–check that the cooling fan assemblies are not operating,
–if fault DF007 UPC-alternator connection is declared present, deal with this fault
first,
–check the conformity of PR010 Alternator charge (see Interpretation of
parameters).
Effect of command:
–for 30 seconds, the Protection and Switching Unit sets the alternator a regulation
voltage of 15 V ± 0.5,
–then for another 30 seconds, the Protection and Switching Unit imposes a
regulation voltage of 13 V ± 0.5 on the alternator.
Switch off all the electrical consumers (fans, main beam headlights, etc.).
Measure the voltage across the alternator terminals, between the B+ terminal and the alternator chassis earth.
Run AC014 Alternator regulation.
Wait 20 seconds,
For 10 seconds the alternator voltage should be 15 V ± 0.5.
Wait 20 seconds,
For 10 seconds the alternator voltage should be 13 V ± 0.5.
Switch on the heated rear screen and the main beam headlights.
Run AC014 again.
Wait 20 seconds,
For 10 seconds the alternator voltage should be 15 V ± 0.5.
Wait 20 seconds,
For 10 seconds the alternator voltage should be 13 V ± 0.5.
If the values obtained are not correct, replace the alternator (see MR 364 or MR 370 Mechanical, 16A, Starting-
Charging, Alternator: Removal - Refitting).
AFTER REPAIRRepeat the conformity check from the start.

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87G
87G - 88V7 MR-372-J84-87G050$770.mif
UPC
Vdiag No.: 48, 4C
AC016
TEST ELECTRICAL SUPPLY CIRCUITS
NOTESSpecial notes:
Switch off the ignition.
This command is used to activate several electrical circuits controlled by the Protection and Switching Unit.
Read the faults.
Deal with present faults,
AFTER REPAIRRun command AC016 Test electrical supply circuits again.