![NISSAN TEANA 2008 Service Manual AV
MULTI AV SYSTEM SYMPTOMS
AV-165
< SYMPTOM DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
RELATED TO AUDIO
RELATED TO STEERING SWITCH
Trouble diagnosis chart by symptom
RELA NISSAN TEANA 2008 Service Manual AV
MULTI AV SYSTEM SYMPTOMS
AV-165
< SYMPTOM DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
RELATED TO AUDIO
RELATED TO STEERING SWITCH
Trouble diagnosis chart by symptom
RELA](/manual-img/5/57391/w960_57391-308.png)
AV
MULTI AV SYSTEM SYMPTOMS
AV-165
< SYMPTOM DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
RELATED TO AUDIO
RELATED TO STEERING SWITCH
Trouble diagnosis chart by symptom
RELATED TO AUXILIARY INPUT
NOTE:
Symptoms Check items Possible malfunction location / Action to take
RGB image is not shown. All RGB images are not shown.
Composite images are not dis-
played.(camera and AUX image) Display unit power supply and ground circuit malfunc-
tion.
Refer to AV- 8 2 , "
DISPLAY UNIT : Diagnosis Proce-
dure".
Communication Circuit malfunction between AV control
unit and display unit.
Perform CONSULT-III self-diagnosis.
Refer to AV- 6 8 , "
CONSULT-III Function (MULTI AV)".
All RGB images are not shown.
Camera image is normal.
AUX images are not displayed. Perform CONSULT-III self-diagnosis.
Refer to AV- 6 8 , "
CONSULT-III Function (MULTI AV)".
All RGB images are not shown.
“Multi AV” is not displayed on system
selection screen when the CONSULT-
III is initialized.AV control unit power supply and ground circuit malfunc-
tion.
Refer to AV- 8 2 , "
AV CONTROL UNIT : Diagnosis Proce-
dure".
All RGB images are not shown.
Composite images are normal. (cam-
era and AUX image) RGB area (YS) signal circuit malfunction.
Refer to AV- 9 0 , "
Diagnosis Procedure".
Color of RGB image is not
proper. (All RGB image)Light blue (Cyan) tint.RGB signal (R: red) circuit malfunction between AV con-
trol unit and display unit.
Refer to AV- 8 6 , "
Diagnosis Procedure".
Purple (Magenta) tint.RGB signal (G: green) circuit malfunction between AV
control unit and display unit.
Refer to AV- 8 7 , "
Diagnosis Procedure".
Screen looks yellowish.RGB signal (B: blue) circuit malfunction between AV con-
trol unit and display unit.
Refer to AV- 8 8 , "
Diagnosis Procedure".
RGB screen is rolling. All RGB screen is rolling.RGB synchronizing signal circuit malfunction between AV
control unit and display unit.
Refer to AV- 8 9 , "
Diagnosis Procedure".
Symptoms Check items Possible malfunction location / Action to take
The CD cannot be removed. —Disk eject signal circuit.
Refer to AV- 9 4 , "
Diagnosis Procedure".
Audio sound is not heard.No sound from all speakers.Perform CONSULT-III self-diagnosis.
Refer to AV- 6 8 , "
CONSULT-III Function (MULTI AV)"
Sound is not heard only from the specific
places (RH front, RH rear, LH front and
LH rear).Sound signal circuit of suspect system
AM/FM radio is not received. Other audio sounds are normal. Antenna amp. ON signal circuit.
Symptoms Probable malfunction location
None of the steering switch operations work.Steering switch signal GND circuit. Refer toAV- 1 0 5 , "
Component In-
spection".
Only specified switch cannot be operated Replace steering switch. Refer to ST-12, "
Exploded View".
Steering switch's “SOURCE”, “MENU UP”, “MENU DOWN”
switches do not work.Steering switch signal A circuit. Refer to AV- 1 0 0 , "
Diagnosis Procedure".
Steering switch's “VOL UP”, “VOL DOWN” switches do not
work.Steering switch signal B circuit. Refer to AV- 1 0 2 , "
Diagnosis Procedure".
![NISSAN TEANA 2008 Service Manual AV-166
< SYMPTOM DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
MULTI AV SYSTEM SYMPTOMS
Check that there is no malfunction of AUX equipment main body before performing a diagnosis.
RELATED TO REAR CONTRO NISSAN TEANA 2008 Service Manual AV-166
< SYMPTOM DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
MULTI AV SYSTEM SYMPTOMS
Check that there is no malfunction of AUX equipment main body before performing a diagnosis.
RELATED TO REAR CONTRO](/manual-img/5/57391/w960_57391-309.png)
AV-166
< SYMPTOM DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
MULTI AV SYSTEM SYMPTOMS
Check that there is no malfunction of AUX equipment main body before performing a diagnosis.
RELATED TO REAR CONTROL SWITCH
Symptoms Check items Probable malfunction location
No voice sound is heard when
AUX mode is selected.Voice sound is heard when other modes
are selected.AUX sound signal circuits malfunction between auxiliary
input jacks and AV control unit.
AUX image is not displayed displayed in black and nothing can be dis-
played RGB area synchronizing (YS) signal circuit malfunc-
tion between AV control unit and display unit.
Refer to AV- 9 0 , "
Diagnosis Procedure".
Horizontal synchronizing (HP) signal circuit malfunc-
tion between AV control unit and display unit.
Refer to AV- 9 1 , "
Diagnosis Procedure".
Vertical synchronizing (VP) signal circuit malfunction
between AV control unit and display unit.
Refer to AV- 9 2 , "
Diagnosis Procedure".
Camera image is normal.AUX image signal circuit malfunction between auxiliary
input jacks and AV control unit.
Refer to AV- 9 3 , "
Diagnosis Procedure".
Symptoms Check items Probable malfunction location
None of the rear control switch operations
work.—Perform CONSULT-III self-diagnosis. Refer
to AV- 6 8 , "
CONSULT-III Function (MULTI
AV )".
![NISSAN TEANA 2008 Service Manual AV-180
< ON-VEHICLE REPAIR >[BASE AUDIO AND DISPLAY SYSTEM]
CAMERA CONTROL UNIT
CAMERA CONTROL UNIT
Exploded ViewINFOID:0000000003940174
Removal and InstallationINFOID:0000000003940175
REMOVAL
1. Remo NISSAN TEANA 2008 Service Manual AV-180
< ON-VEHICLE REPAIR >[BASE AUDIO AND DISPLAY SYSTEM]
CAMERA CONTROL UNIT
CAMERA CONTROL UNIT
Exploded ViewINFOID:0000000003940174
Removal and InstallationINFOID:0000000003940175
REMOVAL
1. Remo](/manual-img/5/57391/w960_57391-323.png)
AV-180
< ON-VEHICLE REPAIR >[BASE AUDIO AND DISPLAY SYSTEM]
CAMERA CONTROL UNIT
CAMERA CONTROL UNIT
Exploded ViewINFOID:0000000003940174
Removal and InstallationINFOID:0000000003940175
REMOVAL
1. Remove rear wheelhouse finisher RH. Refer to INT-57, "Removal and Installation".
2. Remove camera control unit mounting screws, disconnect the camera control unit connector.
3. Remove camera control unit.
INSTALLATION
1. Installation is the reverse order of removal.
2. Perform predicted course line center position adjustment. Refer to AV-47, "
PREDICTED COURSE LINE
CENTER POSITION ADJUSTMENT : Special Repair Requirement".
JPNIA1049ZZ
1. Camera control unit
![NISSAN TEANA 2008 Service Manual AV
REAR VIEW CAMERA
AV-181
< ON-VEHICLE REPAIR >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
REAR VIEW CAMERA
Exploded ViewINFOID:0000000003940176
DISASSEMBLY
Removal and InstallationI NISSAN TEANA 2008 Service Manual AV
REAR VIEW CAMERA
AV-181
< ON-VEHICLE REPAIR >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
REAR VIEW CAMERA
Exploded ViewINFOID:0000000003940176
DISASSEMBLY
Removal and InstallationI](/manual-img/5/57391/w960_57391-324.png)
AV
REAR VIEW CAMERA
AV-181
< ON-VEHICLE REPAIR >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
REAR VIEW CAMERA
Exploded ViewINFOID:0000000003940176
DISASSEMBLY
Removal and InstallationINFOID:0000000003940177
REMOVAL
1. Remove trunk lid finisher inner. Refer to INT-59, "Removal and Installation".
2. Remove trunk lid finisher. Refer to EXT-38, "
Removal and Installation".
3. Remove rear view camera mounting clip, disconnect the rear view camera connector.
4. Remove rear view camera.
INSTALLATION
1. Installation is the reverse order of removal.
AdjustmentINFOID:0000000003970920
Adjust the guide line position if the guide line position is shifted after installing the rear view camera.
1. Draw lines on rearward area of the vehicle passing through the
following points: 200 mm (7.87 in) from both sides of the vehicle,
and 0.5 m (1.64 ft), 1.0 m (3.28 ft) from the rear end of the
bumper.
2. Set into “Adjust offset of rear view camera” mode of Confirma-
tion / Adjustment mode.
JPNIA1050ZZ
1. Rear view camera
2. Seal
Refer to GI-4, "
Components" for symbols in the figure.
SKIB3691E
![NISSAN TEANA 2008 Service Manual AV-182
< ON-VEHICLE REPAIR >[BASE AUDIO AND DISPLAY SYSTEM]
REAR VIEW CAMERA
3. Rotate the center dial, and then select the guiding line pattern so
that its angle is aligned with the correction line o NISSAN TEANA 2008 Service Manual AV-182
< ON-VEHICLE REPAIR >[BASE AUDIO AND DISPLAY SYSTEM]
REAR VIEW CAMERA
3. Rotate the center dial, and then select the guiding line pattern so
that its angle is aligned with the correction line o](/manual-img/5/57391/w960_57391-325.png)
AV-182
< ON-VEHICLE REPAIR >[BASE AUDIO AND DISPLAY SYSTEM]
REAR VIEW CAMERA
3. Rotate the center dial, and then select the guiding line pattern so
that its angle is aligned with the correction line of the rear of the
vehicle.
4. Fine adjust the guiding line so that its position is aligned to the
correction line by pressing the up/down/left/right switches.
Pressing “ENTER” enable the camera control unit to memory
the adjusted guiding line position.
CAUTION:
Never operate other function such as pressing BACK while writing index data.
If Confirmation/Adjustment mode does not function in the above procedure, perform one of the
following service to adjust the index again.
Remove battery for five min. Then reconnect battery.
Remove camera control unit connector for five min. Then reconnect camera control unit connec-
tor.Selected pattern : 7
Up/Down adjustment range : −20 – 20
Left/Right adjustment range : −20 – 20
SKIB3689E
![NISSAN TEANA 2008 Service Manual AV
INSPECTION AND ADJUSTMENT
AV-187
< BASIC INSPECTION >[BOSE AUDIO WITHOUT NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINA NISSAN TEANA 2008 Service Manual AV
INSPECTION AND ADJUSTMENT
AV-187
< BASIC INSPECTION >[BOSE AUDIO WITHOUT NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINA](/manual-img/5/57391/w960_57391-330.png)
AV
INSPECTION AND ADJUSTMENT
AV-187
< BASIC INSPECTION >[BOSE AUDIO WITHOUT NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : De-
scription
INFOID:0000000003765633
WITH AROUND VIEW MONITOR
Always correct the center position of the predicted course line after disconnecting the battery negative termi-
nal.
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Spe-
cial Repair Requirement
INFOID:0000000003765634
1.CORRECTION OF CENTER POSITION OF PREDICTED COURSE LINE
Refer to the following for details.
>> Refer to AV-187, "
PREDICTED COURSE LINE CENTER POSITION ADJUSTMENT : Special
Repair Requirement".
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description
INFOID:0000000003765635
When camera control unit is replaced, the center position of predicted course line shall be corrected.
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Re-
quirement
INFOID:0000000003765636
1.CORRECTION OF CENTER POSITION OF PREDICTED COURSE LINE
Refer to the following for details.
>> Refer to AV-187, "
PREDICTED COURSE LINE CENTER POSITION ADJUSTMENT : Special
Repair Requirement".
PREDICTED COURSE LINE CENTER POSITION ADJUSTMENT
PREDICTED COURSE LINE CENTER POSITION ADJUSTMENT : Description
INFOID:0000000003765637
Adjust the center position of the possible route line of the rear view monitor if it is shifted.
PREDICTED COURSE LINE CENTER POSITION ADJUSTMENT : Special Repair
Requirement
INFOID:0000000003765638
1.STEERING OPERATION
Steer the steering wheel to the leftmost and rightmost ends.
>> GO TO 2.
2.DRIVING
Drive the vehicle straight ahead 100 m (328.1 ft) or more at a speed of 30 km/h (18.6 MPH) or more.
>> END
![NISSAN TEANA 2008 Service Manual AV-190
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
MULTI AV SYSTEM
Component Parts Location
INFOID:0000000003765643
1. Front squawker RH 2. Center speaker 3. Front squawker LH
4. Front door NISSAN TEANA 2008 Service Manual AV-190
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
MULTI AV SYSTEM
Component Parts Location
INFOID:0000000003765643
1. Front squawker RH 2. Center speaker 3. Front squawker LH
4. Front door](/manual-img/5/57391/w960_57391-333.png)
AV-190
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
MULTI AV SYSTEM
Component Parts Location
INFOID:0000000003765643
1. Front squawker RH 2. Center speaker 3. Front squawker LH
4. Front door speaker LH 5. Rear door speaker LH 6. Rear control switch
7. Rear squawker LH 8. Woofer LH 9. BOSE amp.
10. Rear view camera 11. Woofer RH 12. Camera control unit
13. Rear squawker RH 14. Antenna amp. 15. Rear door speaker RH
16. Front door speaker RH 17. Steering angle sensor 18. Steering switch
19. AV control unit 20. Auxiliary input jacks 21. Preset switch
22. DVD player 23. Multifunction switch 24. Display unit
A. Trunk room upper RH B. Trunk room side RH C. Within rear pillar finisher RH
D. Spiral cable part E. In center console F. In grove box
JPNIA1058ZZ
![NISSAN TEANA 2008 Service Manual AV
MULTI AV SYSTEM
AV-191
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
Component DescriptionINFOID:0000000003791245
Part name Description
AV CONTROL UNIT It is t NISSAN TEANA 2008 Service Manual AV
MULTI AV SYSTEM
AV-191
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
Component DescriptionINFOID:0000000003791245
Part name Description
AV CONTROL UNIT It is t](/manual-img/5/57391/w960_57391-334.png)
AV
MULTI AV SYSTEM
AV-191
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
Component DescriptionINFOID:0000000003791245
Part name Description
AV CONTROL UNIT It is the master unit of the MULTI AV system, and it is connected to each control
unit by communication. It operates each system according to communication
signals from the AV control unit.
AV control unit includes audio function and vehicle information function.
It is connected to ECM and combination meter via CAN communication to ob-
tain necessary information for the vehicle information function.
It is connected to BCM via CAN communication transmitting/receiving for the
vehicle settings function.
Composite image signal (AUX and DVD images) is input from DVD player.
Camera image signal is input from camera control unit.
Composite image (DVD, AUX and camera images) signal is output to display
unit.
Sound signal (DVD and AUX sounds) is input from the DVD player.
Power (signal VCC and inverter VCC) is transmitted to front display unit.
DISPLAY UNIT Display image is controlled by the serial communication from AV control unit.
It receives the power (signal VCC and inverter VCC) from the AV control unit
and operates.
RGB image signal is input from AV control unit (RGB, RGB area and RGB syn-
chronizing).
Composite image (DVD, AUX and camera images) signal is input from AV con-
trol unit.
Synchronize signal (HP, VP) is output to AV control unit.
BOSE AMP.Inputs sound signal from AV control unit and DVD player, and outputs sound sig-
nal to woofer and each speaker.
WOOFER Outputs sound signal from BOSE amp.
Outputs low frequency sound.
FRONT SPEAKER Outputs sound signal from BOSE amp.
Outputs sound (mid and low range).
REAR SPEAKER Outputs sound signal from BOSE amp.
Outputs sound (mid and low range).
FRONT SQUAWKER Outputs sound signal from BOSE amp.
Outputs sound (high and mid range).
REAR SQUAWKER Outputs sound signal from BOSE amp.
Outputs sound (high and mid range).
CENTER SPEAKER Outputs sound signal from BOSE amp.
Outputs sound (high and mid range).
MULTIFUNCTION SWITCH Operation panel is equipped with the centralized switch where camera, audio,
DVD and auxiliary input operations are integrated.
The multifunction switch is connected to the preset switch by wiring harness,
and it transmits the operation signal to the preset switch.
PRESET SWITCH Operation panel is equipped with the centralized switch where audio and air
conditioner operations are integrated.
The preset switch is connected via AV communication, and it transmits the op-
eration signals of the preset switch and multifunction switch.
The disk ejection operating signal is performed by wiring harness.
CAMERA CONTROL UNIT Camera image signal is input from rear view camera. Camera image signal
output to AV control unit.
Power supply is transmitted to rear view camera.
AV control unit recognizes the presence of camera system with camera con-
nection recognition signal.
Camera control unit is connected via AV communication.
REAR VIEW CAMERA The image of vehicle rear view is transmitted to camera control unit.
It receives the power supply from the camera control unit and operates.
STEERING ANGLE SENSOR Sensor signal (steering angle) is transmitted to camera control unit.