2008 NISSAN TEANA camera

AV
CAMERA CONTROL UNIT
AV-157
< ECU DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
JCNWM0890GB

AV-158
< ECU DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
CAMERA CONTROL UNIT
JCNWM0891GB

AV
CAMERA CONTROL UNIT
AV-159
< ECU DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
JCNWM0892GB

AV-160
< ECU DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
CAMERA CONTROL UNIT
JCNWM0893GB

AV
CAMERA CONTROL UNIT
AV-161
< ECU DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
JCNWM0894GB

AV-162
< ECU DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
CAMERA CONTROL UNIT
JCNWM0895GB

AV
CAMERA CONTROL UNIT
AV-163
< ECU DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
NOTE:
The name MULTIFUNCTION SWITCH indicates the integration of PRESET SWITCH and MULTIFUNCTION
SWITCH virtually.
JCNWM0896GB

AV-164
< SYMPTOM DIAGNOSIS >[BASE AUDIO AND DISPLAY SYSTEM]
MULTI AV SYSTEM SYMPTOMS
SYMPTOM DIAGNOSIS
MULTI AV SYSTEM SYMPTOMS
Symptom TableINFOID:0000000003882785
RELATED TO VEHICLE INFORMATION
RELATED TO REAR VIEW MONITOR
RELATED TO RGB IMAGE
Symptoms Check items Possible malfunction location / Action to take
Multifunction switch and preset
switch operation does not work. All switches cannot be operated.
 “Multi AV” is displayed on system se-
lection display when the CONSULT-
III is initialized.Perform CONSULT-III self-diagnosis.
Refer to AV- 6 8 , "
CONSULT-III Function (MULTI AV)".
 All switches cannot be operated
 “Multi AV” is not displayed on system
selection screen when the CON-
SULT-III is initialized.AV control unit power supply and ground circuits mal-
function.
Refer to AV- 8 2 , "
AV CONTROL UNIT : Diagnosis Proce-
dure".
Only specified switch cannot be operat-
edMultifunction switch or preset switch malfunction.
Replace multifunction switch or preset switch.
For multifunction switch, refer to AV- 1 7 6 , "
Removal and
Installation".
For preset switch, refer to AV- 1 7 7 , "
Removal and Instal-
lation".
Fuel economy display, vehicle set-
ting operation is abnormalThere is malfunction in the CONSULT-
III self-diagnosis resultPerform detected DTC self-diagnosis.
There is no malfunction in the self-diag-
nosis resultsIgnition signal. Refer to AV- 8 2 , "
AV CONTROL UNIT :
Diagnosis Procedure".
Symptoms Check itemsProbable malfunction location / Action
to take
It cannot be switched to rear view
monitor even when the selector le-
ver is in the reverse position. There is malfunction in the CONSULT-III self-diagno-
sis result.Perform CONSULT-III self-diagnosis.
Refer to AV- 6 8 , "
CONSULT-III Function
(MULTI AV)".
There is not malfunction in the CONSULT-III self-diag-
nosis result.Reverse signal circuit malfunction.(AV
control unit)
Camera image is not shown. AUX images are normal.  Rear view camera power supply cir-
cuit malfunction.
Refer to AV- 8 4 , "
CAMERA CON-
TROL UNIT : Diagnosis Procedure".
 Camera image signal circuit malfunc-
tion.
Refer to AV- 9 6 , "
Diagnosis Proce-
dure".
Possible route line is indicated ab-
normally when camera image is dis-
played.The “Steer. Angle Sensor” is not turned ON at “Con-
nection Confirmation” of “Camera Cont.”Steering angle sensor signal circuits.
Refer to AV-98, "
Diagnosis Procedure".
Camera image is rolling. AUX image is rolling Horizontal synchronizing (HP) signal
circuit malfunction between AV con-
trol unit and display unit.
Refer to AV- 9 1 , "
Diagnosis Proce-
dure".
 Vertical synchronizing (VP) signal cir-
cuit malfunction between AV control
unit and display unit.
Refer to AV- 9 2 , "
Diagnosis Proce-
dure".