2008 NISSAN TEANA Trans

B210E STARTER RELAY
SEC-105
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
SEC
N
O
P
B210E STARTER RELAY
DescriptionINFOID:0000000003815056
Located in IPDM E/R, it runs the starter motor. The starter relay is turned ON by the BCM when the ignition
switch is in the START position. IPDM E/R transmits the starter relay ON signal to BCM via CAN communica-
tion.
DTC LogicINFOID:0000000003815057
DTC DETECTION LOGIC
NOTE:
 If DTC B210E is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
SEC-28, "
IPDM E/R : DTC Logic".
 If DTC B210E is displayed with DTC B2110 for IPDM E/R, first perform the trouble diagnosis for DTC B2110.
Refer to SEC-109, "
DTC Logic".
 If DTC B210E is displayed with DTC B2617 for BCM, first perform the trouble diagnosis for DTC B2617.
Refer to SEC-89, "
DTC Logic".
 When IPDM E/R power supply voltage is low (Approx. 7 - 8 V for about 1 second), the DTC B210F may be
detected.
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON under the following conditions and wait for at least 1 second.
- Selector lever is in the P or N position.
- Do not depress brake pedal.
2. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES >> Go to SEC-105, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000003815058
1.CHECK STARTER RELAY OUTPUT SIGNAL
1. Turn ignition switch OFF.
2. Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK STARTER RELAY OUTPUT SIGNAL CIRCUIT
1. Disconnect IPDM E/R connector.
2. Check continuity between BCM harness connector and IPDM E/R harness connector.
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
B210E STARTER RELAY OFFIPDM E/R detects that the relay is stuck in the OFF position even if
the followings conditions are met for about 1 second.
 Starter control relay ON/OFF signal from BCM
 Park neutral position (PNP) switch input IPDM E/R
Battery
(+)
(–)Condition
Voltage (V)
(Approx.) BCM
Connector Terminal Ignition switch Brake pedal Selector lever
M121 52 Ground ON DepressedP or N Battery voltage
Other than
above0

BCM (BODY CONTROL MODULE)
SEC-175
< ECU DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
SEC
N
O
P
HIGH FLASHER OPERATION
BCM detects the turn signal lamp circuit status by the current value.
BCM increases the turn signal lamp blinking speed if the bulb or harness open is detected with the turn signal
lamp operating.
NOTE:
The blinking speed is normal while activating the hazard warning lamp.
DTC Inspection Priority ChartINFOID:0000000003880728
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.
B2608: STARTER RELAY Inhibit engine cranking500 ms after the following signal communication status becomes
consistent
 Starter motor relay control signal
 Starter relay status signal (CAN)
B2609: S/L STATUS Inhibit engine cranking
 Inhibit steering lockWhen the following steering lock conditions agree
 BCM steering lock control status
 Steering lock condition No. 1 signal status
 Steering lock condition No. 2 signal status
B260A: IGNITION RELAY Inhibit engine cranking500 ms after the following conditions are fulfilled
 IGN relay (IPDM E/R) control signal: OFF (Battery voltage)
 Ignition ON signal (CAN to IPDM E/R): OFF (Request signal)
 Ignition ON signal (CAN from IPDM E/R): OFF (Condition signal)
B260F: ENG STATE SIG LOSTMaintains the power supply
position attained at the time
of DTC detectionWhen any of the following conditions is fulfilled
 Power position changes to ACC
 Receives engine status signal (CAN)
B2612: S/L STATUS Inhibit engine cranking
 Inhibit steering lockWhen any of the following conditions is fulfilled
 Steering lock unit status signal (CAN) is received normally
 The BCM steering lock control status matches the steering lock
status recognized by the steering lock unit status signal (CAN
from IPDM E/R)
B2617: STARTER RELAY CIRC Inhibit engine cranking1 second after the starter motor relay control inside BCM becomes
normal
B2618: BCM Inhibit engine cranking1 second after the ignition relay (IPDM E/R) control inside BCM be-
comes normal
B2619: BCM Inhibit engine cranking1 second after the steering lock unit power supply output control in-
side BCM becomes normal
B261E: VEHICLE TYPE Inhibit engine cranking BCM initialization
B26E1: ENG STATE NO RES Inhibit engine crankingWhen any of the following conditions is fulfilled
 Power position changes to ACC
 Receives engine status signal (CAN)
B26E9: S/L STATUS Inhibit engine cranking
 Inhibit steering lockWhen BCM transmits the LOCK request signal to steering lock unit,
and receives LOCK response signal from steering lock unit, the fol-
lowing conditions is fulfilled
 Steering condition No. 1 signal: LOCK (0 V)
 Steering condition No. 2 signal: LOCK (Battery voltage) Display contents of CONSULT Fail-safe Cancellation
Priority DTC
1 B2562: LOW VOLTAGE
2 U1000: CAN COMM CIRCUIT
 U1010: CONTROL UNIT (CAN)
3 B2190: NATS ANTENNA AMP
 B2191: DIFFERENCE OF KEY
 B2192: ID DISCORD BCM-ECM
 B2193: CHAIN OF BCM-ECM

SRC-122
< COMPONENT DIAGNOSIS >
B1209 FRONTAL COLLISION DETECTION
B1209 FRONTAL COLLISION DETECTION
DescriptionINFOID:0000000003814098
DTC B1209 FRONTAL COLLISION DETECTION
When crash zone sensor detects a component damage resulting from a front collision, the system blinks or
illuminates the air bag warning lamp to inform the driver. Malfunctioning can be detected by the CONSULT-III.
OPERATION
The air bags and seat belt pre-tensioners for driver and front passenger are activated by the air bag diagnosis
sensor unit signal transmitted at the time of the frontal collision.
STRUCTURE
It consists of crash zone sensor, air bag diagnosis sensor unit, air bags and seat belt pre-tensioners for driver
and front passenger.
INSTALLATION
Refer to SR-6, "Exploded View" (Driver air bag module), SR-12, "Exploded View" (Front passenger air bag
module), SR-18, "
Exploded View"(Crash zone sensor), SR-22, "Exploded View" (air bag diagnosis sensor
unit), SB-5, "
SEAT BELT RETRACTOR : Exploded View" (Front LH/RH seat belt pre-tensioner).
DTC LogicINFOID:0000000003814099
DTC CONFIRMATION PROCEDURE
1.CHECK SELF-DIAG RESULT
With CONSULT-III
1. Turn ignition switch ON.
2. Perform “AIR BAG” Self Diagnostic Result.
Without CONSULT-III
1. Turn ignition switch ON.
2. Check the air bag warning lamp status. Refer to SRC-10, "
Air Bag Warning Lamp Diagnosis".
NOTE:
SRS does not enter Diagnosis mode if no malfunction is detected in User mode.
Is malfunctioning part detected?
YES >> Refer to SRC-122, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000003814100
WARNING:
 Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes. (To discharge backup capacitor.)
 Never use unspecified tester or other measuring device.
1.CHECK FRONT AIR BAG MODULE
Check front air bag modules. (driver air bag module and/or front passenger air bag module.)
Is the front air bag module deployed?
YES >> Replace front air bag modules. Refer to SR-6, "Exploded View" or SR-12, "Exploded View".
NO >> GO TO 2.
2.CHECK FRONT SEAT BELT PRE-TENSIONER
Check front seat belt pre-tensioner.
Is the front seat belt pre-tensioner activated?
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
B1209 FRONTAL COLLISION
DETECTIONFront seat belt pre-tensioner, front air
bag is deployed—

SRC-124
< COMPONENT DIAGNOSIS >
B1210 SIDE COLLISION DETECTION
B1210 SIDE COLLISION DETECTION
DescriptionINFOID:0000000003814101
DTC B1210 SIDE COLLISION DETECTION
When satellite sensor detects a component damage resulting from a side collision, blinks or illuminates the air
bag warning lamp to inform the driver. Malfunctioning can be detected by the CONSULT-III.
OPERATION
The front side air bag and side curtain air bag are activated by the air bag diagnosis sensor unit signal trans-
mitted at the time of the side collision.
STRUCTURE
It consists of satellite sensor, air bag diagnosis sensor unit, front side air bag and side curtain air bag.
INSTALLATION
Refer to SR-16, "Exploded View" (Front LH/RH side air bag module), SR-14, "Exploded View"SR-20,
"Exploded View" (LH/RH satellite sensor).
DTC LogicINFOID:0000000003814102
DTC CONFIRMATION PROCEDURE
1.CHECK SELF-DIAG RESULT
With CONSULT-III
1. Turn ignition switch ON.
2. Perform “AIR BAG” Self Diagnostic Result.
Without CONSULT-III
1. Turn ignition switch ON.
2. Check the air bag warning lamp status. Refer to SRC-10, "
Air Bag Warning Lamp Diagnosis".
NOTE:
SRS does not enter Diagnosis mode if no malfunction is detected in User mode.
Is malfunctioning part detected?
YES >> Refer to SRC-124, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000003814103
WARNING:
 Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes. (To discharge backup capacitor)
 Never use unspecified tester or other measuring device.
1.CHECK FRONT SIDE AIR BAG MODULE
Check front side air bag module.
Is the front side air bag module deployed?
YES >> Replace front side air bag module. Refer to SR-16, "Exploded View".
NO >> GO TO 2.
2.CHECK SIDE CURTAIN AIR BAG MODULE
Check side curtain air bag module.
Is the side curtain air bag module deployed?
YES >> Replace side curtain air bag module. Refer to SR-14, "Exploded View".
NO >> GO TO 3.
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
B1210 SIDE COLLISION DE-
TECTIONFront side air bag, side curtain air bag is
deployed—

TM-1
TRANSMISSION & DRIVELINE
C
E
F
G
H
I
J
K
L
M
SECTION TM
A
B
TM
N
O
P
CONTENTS
TRANSAXLE & TRANSMISSION
CVT: RE0F09B
BASIC INSPECTION ....................................
9
DIAGNOSIS AND REPAIR WORK FLOW .........9
Work Flow .................................................................9
Diagnostic Work Sheet ............................................10
INSPECTION AND ADJUSTMENT ....................12
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT ........................................................
12
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Precaution for TCM and CVT
Assembly Replacement ..........................................
12
FUNCTION DIAGNOSIS ..............................13
CVT SYSTEM .....................................................13
System Diagram ......................................................13
Component Parts Location ......................................14
MECHANICAL SYSTEM ....................................16
Cross-Sectional View ..............................................16
System Diagram ......................................................17
System Description .................................................17
Component Parts Location ......................................18
Component Description ...........................................19
HYDRAULIC CONTROL SYSTEM ....................20
System Diagram ......................................................20
System Description .................................................20
Component Parts Location ......................................21
Component Description ...........................................22
CONTROL SYSTEM ..........................................23
System Diagram ......................................................23
System Description .................................................23
Component Parts Location ......................................25
Component Description ...........................................26
LOCK-UP AND SELECT CONTROL SYSTEM
....
27
System Diagram ......................................................27
System Description ..................................................27
Component Parts Location ......................................28
Component Description ...........................................29
SHIFT CONTROL SYSTEM ..............................30
System Diagram ......................................................30
System Description ..................................................30
Component Parts Location ......................................31
Component Description ...........................................32
SHIFT LOCK SYSTEM .....................................33
System Description ..................................................33
Component Parts Location ......................................34
Component Description ...........................................34
ON BOARD DIAGNOSTIC (OBD) SYSTEM ....35
Diagnosis Description ..............................................35
DIAGNOSIS SYSTEM (TCM) ............................37
CONSULT-III Function (TRANSMISSION) ..............37
Diagnostic Tool Function .........................................40
COMPONENT DIAGNOSIS .........................41
U1000 CAN COMM CIRCUIT ...........................41
Description ...............................................................41
DTC Logic ................................................................41
Diagnosis Procedure ...............................................41
P0615 START SIGNAL .....................................42
Description ...............................................................42
DTC Logic ................................................................42
Diagnosis Procedure ...............................................42
P0703 STOP LAMP SWITCH ...........................44
Description ...............................................................44
DTC Logic ................................................................44
Diagnosis Procedure ...............................................44
Component Inspection (Stop Lamp Switch) ............45
P0705 PARK/NEUTRAL POSITION SWITCH ...47
Description ...............................................................47

TM-2
DTC Logic ...............................................................47
Diagnosis Procedure ..............................................47
Component Inspection ............................................48
P0710 CVT FLUID TEMPERATURE SENSOR
...
50
Description ..............................................................50
DTC Logic ...............................................................50
Diagnosis Procedure ..............................................50
Component Inspection (CVT Fluid Temperature
Sensor) ...................................................................
51
P0715 INPUT SPEED SENSOR (PRI SPEED
SENSOR) ...........................................................
52
Description ..............................................................52
DTC Logic ...............................................................52
Diagnosis Procedure ..............................................52
P0720 VEHICLE SPEED SENSOR CVT (SEC-
ONDARY SPEED SENSOR) .............................
55
Description ..............................................................55
DTC Logic ...............................................................55
Diagnosis Procedure ..............................................55
P0725 ENGINE SPEED SIGNAL ......................59
Description ..............................................................59
DTC Logic ...............................................................59
Diagnosis Procedure ..............................................59
P0730 BELT DAMAGE ......................................60
Description ..............................................................60
DTC Logic ...............................................................60
Diagnosis Procedure ..............................................60
P0740 TORQUE CONVERTER CLUTCH SO-
LENOID VALVE .................................................
62
Description ..............................................................62
DTC Logic ...............................................................62
Diagnosis Procedure ..............................................62
Component Inspection (Torque Converter Clutch
Solenoid Valve) ......................................................
63
P0744 A/T TCC S/V FUNCTION (LOCK -UP) ...64
Description ..............................................................64
DTC Logic ...............................................................64
Diagnosis Procedure ..............................................64
Component Inspection (Torque Converter Clutch
Solenoid Valve) ......................................................
65
Component Inspection (Lock-up Select Solenoid
Valve) .....................................................................
65
P0745 LINE PRESSURE SOLENOID VALVE ...66
Description ..............................................................66
DTC Logic ...............................................................66
Diagnosis Procedure ..............................................66
Component Inspection [Pressure Control Sole-
noid Valve A (Line Pressure Solenoid Valve)] ........
67
P0746 PRESSURE CONTROL SOLENOID A
PERFORMANCE (LINE PRESSURE SOLE-
NOID VALVE) ....................................................
68
Description ..............................................................68
DTC Logic ...............................................................68
Diagnosis Procedure ...............................................68
Component Inspection [Pressure Control Sole-
noid Valve A (Line Pressure Solenoid Valve)] ........
69
P0776 PRESSURE CONTROL SOLENOID B
PERFORMANCE (SEC PRESSURE SOLE-
NOID VALVE) ....................................................
70
Description ..............................................................70
DTC Logic ...............................................................70
Diagnosis Procedure ...............................................70
Component Inspection [Pressure Control Sole-
noid Valve A (Line Pressure Solenoid Valve)] ........
71
Component Inspection [Pressure Control Sole-
noid Valve B (Secondary Pressure Solenoid
Valve)] .....................................................................
71
P0778 PRESSURE CONTROL SOLENOID B
ELECTRICAL (SEC PRESSURE SOLENOID
VALVE) ..............................................................
72
Description ..............................................................72
DTC Logic ...............................................................72
Diagnosis Procedure ...............................................72
Component Inspection [Pressure Control Sole-
noid Valve B (Secondary Pressure Solenoid
Valve)] .....................................................................
73
P0840 TRANSMISSION FLUID PRESSURE
SENSOR A (SEC PRESSURE SENSOR) .........
74
Description ..............................................................74
DTC Logic ...............................................................74
Diagnosis Procedure ...............................................74
P0841 PRESSURE SENSOR FUNCTION ........77
Description ..............................................................77
DTC Logic ...............................................................77
Diagnosis Procedure ...............................................77
Component Inspection [Pressure Control Sole-
noid Valve A (Line Pressure Solenoid Valve)] ........
78
Component Inspection [Pressure Control Sole-
noid Valve B (Secondary Pressure Solenoid
Valve)] .....................................................................
78
P0845 TRANSMISSION FLUID PRESSURE
SENSOR B (PRI PRESSURE SENSOR) ..........
80
Description ..............................................................80
DTC Logic ...............................................................80
Diagnosis Procedure ...............................................80
P0868 SECONDARY PRESSURE DOWN ........83
Description ..............................................................83
DTC Logic ...............................................................83
Diagnosis Procedure ...............................................83
Component Inspection [Pressure Control Sole-
noid Valve A (Line Pressure Solenoid Valve)] ........
84

TM-3
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P Component Inspection [Pressure Control Sole-
noid Valve B (Secondary Pressure Solenoid
Valve)] .....................................................................
84
P1701 TRANSMISSION CONTROL MODULE
(POWER SUPPLY) .............................................
85
Description ..............................................................85
DTC Logic ...............................................................85
Diagnosis Procedure ...............................................85
P1705 THROTTLE POSITION SENSOR ...........88
Description ..............................................................88
DTC Logic ...............................................................88
Diagnosis Procedure ...............................................88
P1722 ESTM VEHICLE SPEED SIGNAL ..........89
Description ..............................................................89
DTC Logic ...............................................................89
Diagnosis Procedure ...............................................89
P1723 CVT SPEED SENSOR FUNCTION ........91
Description ..............................................................91
DTC Logic ...............................................................91
Diagnosis Procedure ...............................................91
P1726 ELECTRIC THROTTLE CONTROL
SYSTEM .............................................................
93
Description ..............................................................93
DTC Logic ...............................................................93
Diagnosis Procedure ...............................................93
P1740 LOCK-UP SELECT SOLENOID
VALVE ................................................................
94
Description ..............................................................94
DTC Logic ...............................................................94
Diagnosis Procedure ...............................................94
Component Inspection (Lock-up Select Solenoid
Valve) ......................................................................
95
P1745 LINE PRESSURE CONTROL .................96
Description ..............................................................96
DTC Logic ...............................................................96
Diagnosis Procedure ...............................................96
P1777 STEP MOTOR .........................................97
Description ..............................................................97
DTC Logic ...............................................................97
Diagnosis Procedure ...............................................97
Component Inspection (Step Motor) .......................98
P1778 STEP MOTOR - FUNCTION .................100
Description ............................................................100
DTC Logic .............................................................100
Diagnosis Procedure .............................................100
SHIFT POSITION INDICATOR CIRCUIT .........102
Description ............................................................102
Component Function Check ..................................102
Diagnosis Procedure .............................................102
SHIFT LOCK SYSTEM .....................................103
Description .............................................................103
Wiring Diagram - CVT SHIFT LOCK SYSTEM - ...103
Component Function Check ..................................105
Diagnosis Procedure .............................................106
Component Inspection (Stop Lamp Switch) ..........107
SPORT MODE SWITCH .................................108
Description .............................................................108
Component Function Check ..................................108
Diagnosis Procedure .............................................108
ECU DIAGNOSIS .......................................111
TCM .................................................................111
Reference Value ....................................................111
Wiring Diagram - CVT CONTROL SYSTEM - .......116
Fail-safe .................................................................120
DTC Inspection Priority Chart ................................121
DTC Index .............................................................121
SYMPTOM DIAGNOSIS ............................123
SYSTEM SYMPTOM .......................................123
Symptom Table .....................................................123
PRECAUTION ............................................135
PRECAUTIONS ...............................................135
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ...............................................................
135
Precaution Necessary for Steering Wheel Rota-
tion after Battery Disconnect .................................
135
Precaution for Procedure without Cowl Top Cover ..136
Precaution for On Board Diagnosis (OBD) System
of CVT and Engine ................................................
136
Precaution for TCM and CVT Assembly Replace-
ment .......................................................................
136
Removal and Installation Procedure for CVT Unit
Connector ..............................................................
136
Precaution .............................................................138
Service Notice or Precaution .................................138
ATFTEMP COUNT Conversion Table ...................139
PREPARATION .........................................140
PREPARATION ...............................................140
Special Service Tools ............................................140
Commercial Service Tools .....................................140
ON-VEHICLE MAINTENANCE ..................142
CVT FLUID ......................................................142
Inspection ..............................................................142
Changing ...............................................................143
STALL TEST ...................................................144
Inspection and Judgment ......................................144
LINE PRESSURE TEST ..................................146
Inspection and Judgment ......................................146

TM-4
ROAD TEST .....................................................148
Description .............................................................148
Check before Engine Is Started .............................148
Check at Idle ..........................................................149
Cruise Test ............................................................150
CVT POSITION ................................................152
Inspection and Adjustment ....................................152
ON-VEHICLE REPAIR ...............................153
TRANSMISSION CONTROL MODULE ..........153
Exploded View .......................................................153
Removal and Installation .......................................153
Adjustment .............................................................154
CONTROL DEVICE .........................................155
Exploded View .......................................................155
Removal and Installation .......................................155
Inspection and Adjustment ....................................156
CONTROL CABLE ..........................................157
Exploded View .......................................................157
Removal and Installation .......................................157
Inspection and Adjustment ....................................158
OIL PAN ...........................................................159
Exploded View .......................................................159
Removal and Installation .......................................159
Inspection ..............................................................160
SECONDARY SPEED SENSOR .....................161
Exploded View .......................................................161
Removal and Installation .......................................161
Inspection ..............................................................161
DIFFERENTIAL SIDE OIL SEAL ....................162
Exploded View .......................................................162
Removal and Installation .......................................162
Inspection ..............................................................163
AIR BREATHER HOSE ...................................164
Exploded View .......................................................164
Removal and Installation .......................................164
FLUID COOLER SYSTEM ...............................165
Exploded View .......................................................165
Removal and Installation .......................................165
Inspection ..............................................................167
REMOVAL AND INSTALLATION ..............168
TRANSAXLE ASSEMBLY ..............................168
Exploded View .......................................................168
Removal and Installation .......................................168
Inspection ..............................................................170
DISASSEMBLY AND ASSEMBLY ............172
TORQUE CONVERTER ..................................172
Exploded View .......................................................172
Disassembly ..........................................................172
Assembly ..............................................................172
Inspection ..............................................................173
SERVICE DATA AND SPECIFICATIONS
(SDS) .........................................................
174
SERVICE DATA AND SPECIFICATIONS
(SDS) ................................................................
174
General Specification ............................................174
Vehicle Speed When Shifting Gears .....................174
Stall Speed ............................................................174
Line Pressure ........................................................174
Solenoid Valves ....................................................175
CVT Fluid Temperature Sensor ............................175
Primary Speed Sensor ..........................................175
Secondary Speed Sensor .....................................175
Step Motor ............................................................175
Torque Converter ..................................................175
CVT: RE0F10A
BASIC INSPECTION .................................
176
DIAGNOSIS AND REPAIR WORK FLOW .......176
Work Flow .............................................................176
Diagnostic Work Sheet .........................................177
INSPECTION AND ADJUSTMENT ..................179
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT ......................................................
179
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Service After Replacing TCM
and Transaxle Assembly .......................................
179
FUNCTION DIAGNOSIS ...........................181
CVT SYSTEM ...................................................181
System Diagram ...................................................181
Component Parts Location ...................................182
MECHANICAL SYSTEM ..................................183
Cross-Sectional View ............................................183
System Diagram ...................................................184
System Description ...............................................184
Component Parts Location ...................................185
Component Description ........................................186
HYDRAULIC CONTROL SYSTEM ..................187
System Diagram ...................................................187
System Description ...............................................187
Component Parts Location ...................................188
Component Description ........................................189
CONTROL SYSTEM .........................................190
System Diagram ...................................................190
System Description ...............................................190
Component Parts Location ...................................192
Component Description ........................................193
LOCK-UP AND SELECT CONTROL SYSTEM
..
194