2008 NISSAN TEANA sunroof

SUNROOF MOTOR ASSEMBLY
RF-59
< ECU DIAGNOSIS >
C
D
E
F
G
H
I
J
L
MA
B
RF
N
O
P
JCKWM1235GB

SUNSHADE MOTOR ASSEMBLY
RF-61
< ECU DIAGNOSIS >
C
D
E
F
G
H
I
J
L
MA
B
RF
N
O
P
Wiring Diagram - SUNROOF CONTROL SYSTEM -INFOID:0000000003812870
JCKWM1232GB

SUNROOF DOES NOT OPERATE PROPERLY
RF-65
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
L
MA
B
RF
N
O
P
SYMPTOM DIAGNOSIS
SUNROOF DOES NOT OPERATE PROPERLY
SUNROOF DOES NOT OPEN
SUNROOF DOES NOT OPEN : DescriptionINFOID:0000000003866181
Sunroof does not open when sunroof switch operated.
SUNROOF DOES NOT OPEN : Diagnosis ProcedureINFOID:0000000003812871
1.CHECK SUNROOF MECHANISM
Check the following items.
 Operation malfunction caused by sunroof mechanism deformation, pinched harness or other foreign matter.
 Operation malfunction and interference with other parts by poor installation.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace the malfunctioning parts.
2.CHECK SUNROOF MOTOR ASSEMBLY POWER SUPPLY AND GROUND CIRCUIT
Check sunroof motor assembly power supply and ground circuit.
Refer to RF-11, "
SUNROOF MOTOR ASSEMBLY : DiagnosisProcedure"
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace the malfunctioning parts.
3.CHECK SUNROOF SWITCH
Check sunroof switch.
Refer to RF-15, "
DiagnosisProcedure".
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace the malfunctioning parts.
4.CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES >> Check intermittent incident. Refer to GI-35, "Intermittent Incident".
NO >> GO TO 1.
SUNROOF DOES NOT CLOSE
SUNROOF DOES NOT CLOSE : DescriptionINFOID:0000000003866182
Sunroof does not close though sunroof opens.
SUNROOF DOES NOT CLOSE : Diagnosis ProcedureINFOID:0000000003866183
1.CHECK SUNROOF SWITCH
Check sunroof switch.
Refer to RF-16, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace the malfunctioning part.
2.CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES >> Check intermittent incident. Refer to GI-35, "Intermittent Incident".

RF-66
< SYMPTOM DIAGNOSIS >
SUNROOF DOES NOT OPERATE PROPERLY
NO >> GO TO 1.
SUNROOF DOES NOT TILT UP OR DOWN
SUNROOF DOES NOT TILT UP OR DOWN : DescriptionINFOID:0000000003866184
Sunroof does not tilt though sunroof opens and closes.
SUNROOF DOES NOT TILT UP OR DOWN : Diagnosis ProcedureINFOID:0000000003866185
1.CHECK SUNROOF SWITCH
Check sunroof switch.
Refer to RF-16, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace the malfunctioning part.
2.CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES >> Check intermittent incident. Refer to GI-35, "Intermittent Incident".
NO >> GO TO 1.

RF-68
< SYMPTOM DIAGNOSIS >
AUTO OPERATION DOES NOT OPERATE
AUTO OPERATION DOES NOT OPERATE
Diagnosis ProcedureINFOID:0000000003812873
1.PERFORM INITIALIZATION PROCEDURE
Initialization procedure is executed and operation is confirmed.
Refer to RF-4, "
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement".
Is the inspection result normal?
YES >> Sunroof and sunshade system is normal.
NO >> GO TO 2.
2.CHECK SUNROOF SWITCH
Check sunroof switch.
Refer to RF-15, "
DiagnosisProcedure".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace the malfunctioning parts.
3.CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES >> Check intermittent incident. Refer to GI-35, "Intermittent Incident".
NO >> GO TO 1.

RF-70
< SYMPTOM DIAGNOSIS >
ANTI-PINCH FUNCTION DOES NOT OPERATE
ANTI-PINCH FUNCTION DOES NOT OPERATE
Diagnosis ProcedureINFOID:0000000003812875
1.CHECK SUNROOF AND SUNSHADE MECHANISM
Check the following items.
 Operation malfunction caused by sunroof and sunshade mechanism deformation, pinched harness or other
foreign matter.
 Operation malfunction and interference with other parts by poor installation.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace the malfunctioning parts.
2.PERFORM INITIALIZATION
Perform initialization procedure.
Refer to RF-4, "
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement".
Is the inspection result normal?
YES >> Sunroof and sunshade system is normal.
NO >> GO TO 1.

SQUEAK AND RATTLE TROUBLE DIAGNOSES
RF-73
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
L
MA
B
RF
N
O
P
Inspection ProcedureINFOID:0000000003940147
Refer to Table of Contents for specific component removal and installation information.
INSTRUMENT PANEL
Most incidents are caused by contact and movement between:
1. Cluster lid A and instrument panel
2. Acrylic lens and combination meter housing
3. Instrument panel to front pillar garnish
4. Instrument panel to windshield
5. Instrument panel mounting pins
6. Wiring harnesses behind the combination meter
7. A/C defroster duct and duct joint
These incidents can usually be located by tapping or moving the components to duplicate the noise or by
pressing on the components while driving to stop the noise. Most of these incidents can be repaired by apply-
ing felt cloth tape or silicon spray (in hard to reach areas). Urethane pads can be used to insulate wiring har-
ness.
CAUTION:
Never use silicone spray to isolate a squeak or rattle. If the area is saturated with silicone, the recheck
of repair becomes impossible.
CENTER CONSOLE
Components to pay attention to include:
1. Shifter assembly cover to finisher
2. A/C control unit and cluster lid C
3. Wiring harnesses behind audio and A/C control unit
The instrument panel repair and isolation procedures also apply to the center console.
DOORS
Pay attention to the following:
1. Finisher and inner panel making a slapping noise
2. Inside handle escutcheon to door finisher
3. Wiring harnesses tapping
4. Door striker out of alignment causing a popping noise on starts and stops
Tapping or moving the components or pressing on them while driving to duplicate the conditions can isolate
many of these incidents. The areas can usually be insulated with felt cloth tape or insulator foam blocks to
repair the noise.
TRUNK
Trunk noises are often caused by a loose jack or loose items put into the trunk by the customer.
In addition look for the following:
1. Trunk lid dumpers out of adjustment
2. Trunk lid striker out of adjustment
3. Trunk lid torsion bars knocking together
4. A loose license plate or bracket
Most of these incidents can be repaired by adjusting, securing or insulating the item(s) or component(s) caus-
ing the noise.
SUNROOF/HEADLINING
Noises in the sunroof/headlining area can often be traced to one of the following:
1. Sunroof lid, rail, linkage or seals making a rattle or light knocking noise
2. Sunvisor shaft shaking in the holder
3. Front or rear windshield touching headlining and squeaking
Again, pressing on the components to stop the noise while duplicating the conditions can isolate most of these
incidents. Repairs usually consist of insulating with felt cloth tape.

GLASS LID
RF-79
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
MA
B
RF
N
O
P
ON-VEHICLE REPAIR
GLASS LID
Exploded ViewINFOID:0000000003812884
1. Roof side finisher RH 2. Rear link cover 3. TORX bolt
4. Glass lid 5. Roof side finisher LH 6. Inner blind
7. Sunroof unit assembly 8. Sunroof motor assembly 9. Sunshade motor assembly
Refer to GI-4, "
Components" for symbols in the figure.
JMKIA2488GB