2008 MITSUBISHI SHOGUN ignition

Instruments and controls
3-3
3
Odometer/Tripmeter/Service reminder
E00500600998
With the ignition switch in the “ON” position, odometer, tripm- eter, and service reminder indications are given.
Odometer The odometer indicates the tota
l distance the vehicle has trav-
elled.TripmeterThe tripmeter indicates the dist
ance travelled during a particu-
lar trip or period. There are two tripmeter displays: TRIP and . TRIP can be used to measur
e the distance travelled since
the current trip began. At the same time, TRIP can be used to measure the dist
ance from an inte
rmediate location.
To switch the display between TRIP and TRIP , press the reset button (B) less than 1 second.
A- Odometer/Tripmeter/Service reminder B- Reset button
TRIP ODOService reminder TRIP ODO
BK-BK2008E1ENUK.en-uk-Section6.fm Page 3 Wednesday, January 9, 2008 4:32 PM

3-4 Instruments and controls
3
NOTE●
If you do not push the button for about 10 seconds while the service reminder is showing, the display will return to the odometer indication.
●
The odometer, tripmeter, an
d service reminder indications
are given for 30 seconds after the ignition switch has been turned to the “ACC” or “LOCK” position.
●
After the odometer, tripmeter, and service reminder indi- cations have gone off, they come back on for about 30 seconds if either of the fo
llowing actions takes place.
• The driver’s door is opened.• The reset button is pressed.
To reset the tripmeter To return the display to “0”, press the reset button (B) for morethan 2 second. Only the currently displayed value will be reset.NOTE●
When disconnecting the battery
terminal for a long time,
the memory of tripmeter display TRIP and are cleared, and the display returns to “0”.
Service reminder
E00517700092
The service reminder shows the number of months (1) anddriving distance (3) remaining until the next 12-monthly(15,000 km or 9,000 miles) inspection. When the next inspec- tion is nearly due, the display s
hows “-----”. At this time, a
spanner mark (2) is shown for a few seconds whenever theignition switch is turned from the “OFF” position to the “ON” position.
BK-BK2008E1ENUK.en-uk-Section6.fm Page 4 Wednesday, January 9, 2008 4:32 PM

Instruments and controls
3-5
3
1. The display shows the number of months and driving dis-
tance remaining until the next inspection.
2. When the next inspection is nearly due, the display shows
“-----”. For further information, we recommend you to consult aMITSUBISHI MOTORS Authorized Service Point. At this time, a spanner mark is shown for a few seconds whenever the ignition switch
is turned from the “OFF”
position to the “ON” position.
3. When the vehicle is inspected at a MITSUBISHI
MOTORS Authorized Servi
ce Point, the number of
months and driving distance remaining until the next inspection will be shown.
NOTE●
The indicated distance decreases
in steps of 100 km (or
100 miles). The indicated num
ber of months decreases in
steps of one month.
●
It is possible to change the settings for the service reminder. For further information, we recommend you to consult a MITSUBISHI MOTORS Auth
orized Service Point.
BK-BK2008E1ENUK.en-uk-Section6.fm Page 5 Wednesday, January 9, 2008 4:32 PM

3-6 Instruments and controls
3
Resetting the service reminder With the ignition switch in the “OFF” position, it is possible to reset the spanner mark (A) and “-----” indication (B). When they have been reset, the number of months and driving dis-tance remaining until the next inspection are shown and the spanner mark (A) is no longer shown every time the ignition switch is turned from the “OFF
” position to the “ON” position.
BK-BK2008E1ENUK.en-uk-Section6.fm Page 6 Wednesday, January 9, 2008 4:32 PM

Instruments and controls
3-7
3
1. Push the reset button (D) to view the number of months
and driving distance remaining until the next inspection.
2. Give the reset button (D) a long push (at least two sec-
onds) to make the spanner mark (A) start flashing. (If youdo not touch the reset button for 10 seconds while the spanner mark is flashing, the display will revert to its orig- inal indication.)
3. Give the reset button (D) a gentle push while the spanner
mark is flashing. The “-----” indication (B) will change to “cLEAr” (C).
4. The number of months and driving distance remaining
until the next inspection will be shown.
NOTE●
It is not possible to reset the “-----” indication (B) with the ignition switch in the “ON” position.
●
When a certain distance has
been driven and a certain
period has elapsed after app
earance of the “-----” indica-
tion (B), the indication is automatically reset and the number of months until the next periodic inspection isshown.
●
If you accidentally reset th
e display, consult a MITSU-
BISHI MOTORS Author
ized Service Point.
Fuel gauge
E00500700638
The fuel gauge indicates the fuel
level in the fuel tank when the
ignition switch is in the “ON” position.
CAUTION
!●
Daily and periodic inspect
ions and maintenance are
your responsibility. Be sure to perform them to help prevent accidents and breakdowns.
F- Full E- Empty
CAUTION
!●
For petrol-powered vehicles, do not drive with an extremely low fuel level;
running out of fuel could
cause damage to the catalytic converter.
●
For diesel-powered vehicl
es, do not drive with an
extremely low fuel level;
running out of fuel could
cause damage to the fuel system.
BK-BK2008E1ENUK.en-uk-Section6.fm Page 7 Wednesday, January 9, 2008 4:32 PM

3-8 Instruments and controls
3
NOTE●
When the vehicle has been re
fuelled, the pointer in the
fuel gauge takes a short while to stabilize.
●
The fuel gauge will not give
an accurate indication if the
vehicle is refuelled with the ignition switch in the “ON”position.
●
When the engine on diesel-pow
ered vehicles fails to oper-
ate owing to running out of fuel, it may sometimes be dif-ficult to start after refuelling.
This is due to air entering
the fuel system. Therefore, ai
r must be bled from the sys-
tem. (Refer to “Bleeding th
e fuel system” on page 6-9.)
Fuel lid markThe fuel lid mark (A) indicates
that the fuel tank filler door is
located on the right side of the vehicle.
Low fuel warning lamp
E00508100595
The warning lamp (A) illuminates when the fuel level is get-ting low (approx. 10 litres) with the ignition switch in the “ON” position. Refuel as soon as possible.NOTE●
On inclines or curves, due to
the movement of fuel in the
tank, the low fuel warning lamp may indicate incorrectly.
BK-BK2008E1ENUK.en-uk-Section6.fm Page 8 Wednesday, January 9, 2008 4:32 PM

Instruments and controls
3-9
3
Water temperature gauge
E00500800408
The water temperature gauge indi
cates the engine coolant tem-
perature when the ignition switch is in the “ON” position.
Daytime dipper button (meter illumination con- trol)
E00508800097
Turn the dial to adjust the i
llumination (meter, multi centre dis-
play, audio system’s control panel, heater control panel, etc.) tothe desired brightness.NOTE●
The meter brightness
stays memorized.
CAUTION
!●
If the indication needle en
ters the H zone while the
engine is running, it indica
tes that the engine is pos-
sibly overheating. Immediat
ely park your vehicle in
a safe place and make th
e necessary corrections.
(Refer to “Engine overheating” on page 6-6.) While driving, care should always be taken to main-tain the normal operating temperature.
1- To reduce brightness 2- To increase brightness
Brightness
BK-BK2008E1ENUK.en-uk-Section6.fm Page 9 Wednesday, January 9, 2008 4:32 PM

3-12 Instruments and controls
3
Indicator lamps
E00501600012
Turn-signal indication lamps/Hazard warning indication lamps
E00501700068
These indication lamps blink on and off when a turn-signal lamp is operating.NOTE●
If the blinking is too fast, a lamp bulb may be blown or a turn-signal connection may be false.
When the hazard warning lamp switch is pressed, all turn-signal lamps will flash on andoff continuously.High-beam indicator lamp
E00501800072
This indicator lamp illuminates when the highbeam is used.Front fog lamp indication lamp*
E00501900132
This indication lamp illuminates while the frontfog lamps are on.
Rear fog lamp indication lamp
E00502000084
This indication lamp illuminates while the rearfog lamp is on.Position lamp indication lamp
E00508900102
This lamp illuminates with the lamp switch at “ ” or “ ” position.Diesel preheat indica
tion lamp (diesel-
powered vehicles)
E00502300029
This indication lamp illuminates when the igni- tion switch is placed in the “ON” position. Asthe glow plug becomes hot, the lamp goes out and the engine can be started.NOTE●
If the engine is cold,
the diesel preheat indi-
cation lamp is on for a longer time.
●
When the engine has not been started within about 5 seconds after the diesel preheatindication lamp went out, return the ignition switch to the “LOCK” position. Then, turn the switch to the “ON” position to preheat the engine again.
●
When the engine is warm, the diesel preheat indication lamp does not come on even if the ignition switch is placed in the “ON” position.
BK-BK2008E1ENUK.en-uk-Section6.fm Page
12 Wednesday, January 9, 2008 4:32 PM