2008 MITSUBISHI SHOGUN clock

3-34 Instruments and controls
3
2. It is possible to adjust the clock using the function buttons
3. After making the adjustment, press the “INFO” button to
select the information display.
NOTE●
Vehicles equipped with the Mitsubishi Multi Communica- tion System (MMCS) also have a clock indication, but the time shown by the MMCS may differ from that shown by the centre information disp
lay because different sources
of data are used for automatic adjustment.
“H”- Adjust “hour”.
The indication increases by one hour, every time youlightly press the “H” function button. If you continuepressing the button for about 2 seconds or more, theindication is fast-forwarded, and then the setting ischanged to the hour selected.
“M”- Adjust “minute”.
The indication increases by one minute, every time youlightly press the “M” function button. If you continuepressing the button for about 2 seconds or more, theindication is fast-forwarded, and then the setting ischanged to the minute selected.
“SET”- To reset the minutes to zero.
The time is adjusted as described below by pressing thefunction button “SET”.●
10:30-11:29 · · · · Change to 11:00
●
11:30-12:29 · · · · Change to 12:00
In this occasion, the display flashes twice before the set-ting is changed.
BK-BK2008E1ENUK.en-uk-Section6.fm Page
34 Wednesday, January 9, 2008 4:32 PM

For pleasant driving
5-5
5
NOTE●
There is an interior air temper
ature sensor (A) in the illus-
trated position. Never place anything on top of
the sensor, since doing so
will prevent it from functioning properly.
Blower speed selection dial
E00702800198
Select the blower speed by turn
ing the blower speed selection
dial clockwise or anticlockwise. The blower speed will gradu- ally increase as the dial is turned to the right.The selected blower speed will
be shown by the front blower
speed display (A).1- Increase 2- Decrease
BK-BK2008E1ENUK.en-uk-Section8.fm Page 5 Wednesday, January 9, 2008 4:41 PM

5-6 For pleasant driving
5
Temperature control dial
E00703000403
Turn the temperature control di
al clockwise or anticlockwise.
The selected temperature will be
shown by the temperature dis-
play (A).NOTE●
While the engine coolant temp
erature is low, the tempera-
ture of the air from the heater will be cool/cold until the engine warms up, even if you have selected warm air withthe dial.
Air selection switch
E00703400436
To change the air selection,
simply press the air selection
switch. ●
Outside air: Indication lamp (A) is OFF Outside air is introduced into the passenger compartment.
●
Recirculated air: Indication lamp (A) is ON Air is recirculated inside the passenger compartment.
BK-BK2008E1ENUK.en-uk-Section8.fm Page 6 Wednesday, January 9, 2008 4:41 PM

5-18 For pleasant driving
5
Ty p e B Select the desired temperature level by turning clockwise or anticlockwise.NOTE●
If your vehicle is equipped with rear air conditioning, the rear air conditioning will no
t operate unless the front air
conditioning compressor is operating. Always switch the front air conditioning compressor onbefore using the rear air condi
tioning. If th
e front air con-
ditioning compressor is not operating, the system will just operate as a blower.
Important operation tips for the air
conditioning
E00708300746
●
Park the vehicle in the shade. Parking in the hot sun will make the vehicle inside extremely hot, and it will require more time to cool theinterior. If it is necessary to park in the sun, open the windows for the first few minutes of air conditioning operation to expelthe hot air.
●
Close the windows when the air conditioning is in use. The entry of outside air through open windows willreduce the cooling efficiency.
●
Too much cooling is not good for the health. The inside air temperature should only be 5 to 6 °C below the outsideair temperature.
●
When operating the system,
make sure the air intake,
which is located in front of the windscreen, is free ofobstructions such as leaves
as snow. Leaves collected in
the air-intake plenum may reduce air flow and plug the plenum water drains.
BK-BK2008E1ENUK.en-uk-Section8.fm Page
18 Wednesday, January 9, 2008 4:41 PM

For pleasant driving
5-27
5
Radio data system (RDS)
E00709200162
1- AM/FM (FM/MW/LW selection) button 2- PWR (On-Off) button3- Memory select buttons 4- MENU button 5- SEEK (Down-seek) button6- SEEK (Up-seek) button 7- TUNE (Down-step) button 8- TUNE (Up-step) button9- TP (Traffic program) button 10- PTY (Program type) button 11- RDS (Radio data system) indicator12- PTY (Program type) indicator13- REG (Regional program) indicator 14- TP (Traffic program identification) indicator 15- CT (Clock time) indicator
16- Display
BK-BK2008E1ENUK.en-uk-Section8.fm Page
27 Wednesday, January 9, 2008 4:41 PM

5-28 For pleasant driving
5
RDS uses PI (program identification) signal and AF (alterna- tive frequency) list transmitted in addition to the normal FM broadcasting programs, and picks
up the FM stations that are
transmitting the same program from the AF list and automati-cally tunes to the station with the strongest signal intensity. Therefore, you can co
ntinue listening to one program in, for
example, a long dist
ance driving without retuning to the other
station transmitting the same
program when you are leaving
the service area of the cu
rrently receiving station.
The RDS radio also features th
e limited reception of the pro-
gram types, the break-in reception of the traffic announcement to the EON (enhanced other network) and emergency broad- cast, and the limited/
unlimited reception of
the regional pro-
grams.AF (Alternative Frequencies) function
E00720900090
The AF function finds a station broadcasting the same programand selects the station with the strongest signal of AF lists. The AF function is turned on at all times unless you manually switch it off. The AF function can be turned ON and OFF. Refer to “Adjusting the time” on page 3-19.CT (Clock Time) function
E00721000085
The clock can be set automatically
by using the signal from the
local RDS stations. Refer to “Adjusting the time” on page
3-19
.
REG (Regional) function
E00721100028
REG function limits to receive the stations broadcastingregional programs. Regional programming and regional networks are organizeddifferently depending on the country or area (they may be changed according to the hour, st
ate, or broadcast area), so if
you don’t want to receive the re
gional programs automatically,
you can set up REG ON not to
receive regional programs.
The REG function can be
turned ON and OFF.
Refer to “Function setup mode” on page 5-33.PI (Program Identification) search function
E00721200133
When travelling long distance a
nd the recalled preset station is
weak, the radio searches anot
her frequency broadcasting the
same programming with the same PI code in AF list. If there are no frequencies br
oadcasting the same program-
ming, the radio searches a frequency broadcasting the regionalprogramming. The radio succeeds in searching the regional programming, then the display shows the REG indicator (13). If the radio does not succeed
in searching the regional pro-
gramming, the radio returns to
the recalled preset station.
The PI function can be turned ON and OFF on some vehicles. Refer to “Function setup mode” on page 5-33.NOTE●
While searching, the audio sy
stem is muted. The display
shows “WAIT” or “SEARCH”.
BK-BK2008E1ENUK.en-uk-Section8.fm Page
28 Wednesday, January 9, 2008 4:41 PM

5-52 For pleasant driving
5
Radio data system (RDS)
E00709200175
1- AM/FM (FM/MW/LW selection) button 2- PWR (On-Off) button3- Memory select buttons 4- MENU button 5- SEEK (Down-seek) button6- SEEK (Up-seek) button 7- TUNE (Down-step) button 8- TUNE (Up-step) button9- TP (Traffic program) button 10- PTY (Program type) button 11- RDS (Radio data system) indicator12- PTY (Program type) indicator13- REG (Regional program) indicator 14- TP (Traffic program identification) indicator 15- CT (Clock time) indicator
16- Display
BK-BK2008E1ENUK.en-uk-Section8.fm Page
52 Wednesday, January 9, 2008 4:41 PM

For pleasant driving
5-53
5
RDS uses PI (program identifi
cation) signal and AF (alterna-
tive frequency) list transmi
tted in addition to the normal FM
broadcasting programs, and picks up the FM stations that are transmitting the same program from the AF list and automati-cally tunes to the station with the strongest signal intensity. Therefore, you can continue listening to one program in, for example, a long distance driving without retuning to the otherstation transmitting the same
program when you are leaving
the service area of the cu
rrently receiving station.
The RDS radio also features th
e limited reception of the pro-
gram types, the break-in receptio
n of the traffic announcement
to the EON (enhanced other network) and emergency broad- cast, and the limite
d/unlimited recep
tion of the regional pro-
grams.AF (Alternative Frequencies) function
E00720900104
The AF function finds a statio
n broadcasting the same program
and selects the station with th
e strongest signal of AF lists.
The AF function is turned on at all times unless you manually switch it off. The AF function can be turned ON and OFF. Refer to “Function setup mode” on page 5-57.CT (Clock Time) function
E00721000098
The clock can be set automatically by using the signal from thelocal RDS stations. Refer to
“Adjusting the time” on page
3-19
.
REG (Regional) function
E00721100015
REG function limits
to receive the stations broadcasting
regional programs. Regional programming and regional networks are organizeddifferently depending on the country or area (they may be changed according to the hour, state, or broadcast area), so if you don’t want to receive the re
gional programs automatically,
you can set up REG ON not to
receive regional programs.
The REG function can be turned ON and OFF. Refer to “Function setup mode” on page 5-57.PI (Program Identification) search function
E00721200146
When travelling long distance an
d the recalled preset station is
weak, the radio searches another frequency broadcasting the same programming with the same PI code in AF list. If there are no frequencies broadcasting the same program- ming, the radio searches a frequ
ency broadcasting the regional
programming. The radio succeeds
in searching the regional
programming, then the display shows the REG indicator (13). If the radio does not succeed
in searching the regional pro-
gramming, the radio returns to
the recalled preset station.
The PI function can be turned ON and OFF on some vehicles. Refer to “Function setup mode” on page 5-57.NOTE●
While searching, the audio sy
stem is muted. The display
shows “WAIT” or “SEARCH”.
BK-BK2008E1ENUK.en-uk-Section8.fm Page
53 Wednesday, January 9, 2008 4:41 PM