2008 MITSUBISHI SHOGUN clock

For pleasant driving
5-107
5
Installation position for warning triangle
E00718400085
There are securing bands (A) for the warning triangle on the backdoor. To remove or install the warning triangle, turn the lock knobs(B) counter clockwise, then
remove the backdoor lid (C).
NOTE●
The warning triangle shown in the illustration is not sup- plied with the vehicle. It is recommended one be obtainedand carried for use if required.
BK-BK2008E1ENUK.en-uk-Section8.fm Page
107 Wednesday, January 9, 2008 4:41 PM

For emergencies
6-19
6
3. Remove the bolts (B) by turning them anticlockwise with
the wheel nut wrench.
4. Close the backdoor.
BK-BK2008E1ENUK.en-uk-Section9.fm Page
19 Wednesday, January 9, 2008 4:46 PM

6-22 For emergencies
6
2. Using the jack handle, turn
the release valve (A) clock-
wise until it stops.
3. Insert the jack handle in the bracket of the jack and hook
the notch (B) on the jack handle
end to the claw (C) of the
bracket.
BK-BK2008E1ENUK.en-uk-Section9.fm Page
22 Wednesday, January 9, 2008 4:46 PM

6-26 For emergencies
6
10. Put the notch (J) provided on the jack handle end on the
valve (K) of the jack. Using the jack handle, turn the release valve anticlock- wise slowly to lower the vehicle until the tyre touches theground.
11. Tighten the nuts crisscross
in 2 or 3 steps until each nut
has been tightened securely. Tightening torque 105 to 125 Nm (Achieved by applying a force of 390 to 460 N at the endof the wheel nut wrench s
upplied with the vehicle.)
WARNING
!●
Be sure to open the release valve slowly. If it is opened quickly, the vehicl
e will drop abruptly and
the jack may come out of
position, causing a serious
accident.
CAUTION
!●
Never use your foot or a pipe extension for extra force in the wheel nut wren
ch. If you do so, you will
tighten the nut too much.
BK-BK2008E1ENUK.en-uk-Section9.fm Page
26 Wednesday, January 9, 2008 4:46 PM

For emergencies
6-27
6
12. Lower the jack all the way and remove it.
NOTE●
Occasionally when the vehicle is jacked up, the grooved portion of the designated point will not come off. When this happens, rock the
vehicle to lower the ram.
●
If the jack is difficult to remove by hand, insert the jack handle (L) into the bracket (M). Then using the handle, remove the jack.
CAUTION
!●
If the release valve is loos
ened too much (2 or more
turns) in the anticlockwise
direction, the jack’s oil
will leak and the jack cannot be used.
●
Close the release valve slowly when lowering the vehicle, or the valve may be damaged.
BK-BK2008E1ENUK.en-uk-Section9.fm Page
27 Wednesday, January 9, 2008 4:46 PM

8-38 Maintenance
8
Inside
E01003400814
Headlamps
E01003500961
Replacement of high beam1. Remove the bulb and connector assembly (A) by turning
it anticlockwise.
1- Luggage compartment lamp: 8 W 2- Door courtesy lamps*: 3.4 W 3- Vanity mirror lamps*: 3 W 4- Room & map lamps: 8 W5- Rear personal lamps: 8 W 6- Glove box lamp: 1.4 W
BK-BK2008E1ENUK.en-uk-Section11.fm Page
38 Wednesday, January 9, 2008 4:50 PM

Maintenance
8-39
8
2. Depress the tab (B) on the harness connector and pull the
harness connector (C) to remove it.
3. To install the bulb, perform the removal steps in reverse.
Replacement of low beam1. Remove the bulb and connector assembly (A) by turning
it anticlockwise.
BK-BK2008E1ENUK.en-uk-Section11.fm Page
39 Wednesday, January 9, 2008 4:50 PM

Maintenance
8-41
8
Position lamps
E01003700471
1. Turn the bulb socket an
ticlockwise to remove it.
2. Remove the bulb from the socket by pulling out. 3. To install the bulb, perform the removal steps in reverse.
Front turn-signal lamps
E01003800414
1. Turn the bulb socket anticlockwise to remove it. 2. Remove the bulb from the socket by pulling out 3. To install the bulb, perform the removal steps in reverse.
BK-BK2008E1ENUK.en-uk-Section11.fm Page
41 Wednesday, January 9, 2008 4:50 PM