2008 Lancia Musa ESP

173
WARNING
LIGHTS AND
MESSAGES
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
fig. 5 - 1.4 8V version(where provided)L0D0258mfig. 6 -1.416VversionL0D0208mfig. 7 - 1.3 Multijet versionL0D0209m
fig. 8 - 1.9 Multijet versionL0D0326m
ENGINE OIL fig. 5-6-7-8
Engine oil check
Check the oil level a few minutes
(about 5) after the engine has
stopped, with the car parked on level
ground.
The oil level must be included be-
tween the MINandMAXmarks on
the dipstick. The range between the
MINandMAXlevels corresponds to
approximately 1 litre of oil.Topping up the engine oil
If the oil level is near or under the
MINline, add oil through the filler to
reach the MAXline. Oil level shall
never exceed the MAXline.
IMPORTANT If, following the rou-
tine checks, the engine oil level is
found to be above the MAXline, con-
tact the Lancia Dealership in order to
have the correct level restored.
IMPORTANT After adding or chang-
ing the oil, before checking the level,
run the engine for a few seconds and
wait for a few minutes after it has
stopped.
165-186 MUSA 3ed GB 12-11-2007 11:39 Pagina 173

188
WARNING
LIGHTS AND
MESSAGES
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
IDENTIFICATION
DATA
Take note of the identification codes.
The identification data stamped on
the platesfig. 1and their respective
positions are as follows:
1- Model plate.
2- Chassis marking
3- Bodywork paint identification
plate
4- Engine marking.MODEL PLATE fig. 2
This plate is applied to the engine
compartment front beam and shows
the following identification data:
B- Homologation number.
C- Vehicle type code.
D- Chassis number.
E- Maximum vehicle weight fully
loaded.
F- Maximum vehicle weight fully
loaded plus trailer.G- Maximum weight on front axle.
H- Maximum vehicle weight on rear
axle.
IEngine type.
L- Body version code.
M- Spare part code.
N- Smoke opacity index (for diesel
engines).
fig. 1L0D0450mfig. 2L0D0415m
187-205 MUSA 3ed GB 12-11-2007 11:40 Pagina 188

189
WARNING
LIGHTS AND
MESSAGES
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
CHASSIS MARKING fig. 3
This is printed on the passenger com-
partment floor bed near the front
right seat.
To access it, lift the opening cut in the
carpet for this purpose; it shows:
❒car model;
❒chassis number.
BODYWORK PAINT
IDENTIFICATION PLATE fig. 4
This plate is applied to the front bon-
net and shows the following data:
A- Paint manufacturer.
B- Colour name.
C- Lancia colour code.
D- Respray and touch up code.ENGINE MARKING
Engine marking is stamped on the
motor block, passenger compartment
side, and includes the model and the
chassis number.
fig. 3L0D0227m
fig. 4L0D0228m
187-205 MUSA 3ed GB 12-11-2007 11:40 Pagina 189

191
WARNING
LIGHTS AND
MESSAGES
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
1.3 Multijet 70HP
188A9000
Diesel
4 in line
4
69.6 x 82
1248
18±0.4
51
70
4000
180
18,3
1750
–
Diesel fuel for
motor vehicles
(Specification
EN590)
1.3 Multijet 90HP
199A3000
Diesel
4 in line
4
69.6 x 82
1248
17,6±0.4
66
90
4000
200
20
1750
–
Diesel fuel for
motor vehicles
(Specification
EN590)
ENGINE
INTRODUCTION
Engine code
Cycle
Number and layout of cylinders
Number of valves per cylinder
Piston bore and stroke mm
Total displacement cm3
Compression ratio
Maximum power (EEC) kW
HP
corresponding ratio: rpm
Maximum torque (EEC) Nm
kgm
corresponding ratio: rpm
Spark plugs
Fuel
(▲)Engine provided for some versions/markets only
1.48V(▲)
350A1000
Otto
4 in line
2
72 x 84
1368
11±0.2
57
77
6000
115
11,7
3000
NGK ZKR7A-10
Unleaded petrol
95 RON
(Specification
EN228)1.9 Multijet
188B2000
Diesel
4 in line
2
82 x 90.4
1910
18±1
74
100
4000
260
26.4
2000
–
Diesel fuel for
motor vehicles
(EN590 specifica-
tions) 1.4
16V
843A1000
Otto
4 in line
4
72 x 84
1368
11±0.2
70
95
5800
128
13
4500
NGK ZKR7A-10
Unleaded petrol
95 RON
(Specification
EN228)
187-205 MUSA 3ed GB 12-11-2007 11:40 Pagina 191

194
WARNING
LIGHTS AND
MESSAGES
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
WHEELS
RIMS AND TYRES fig. 5
Pressed steel or alloy rims. Tubeless
radial carcass tyres. All approved
tyres are listed in the Log Book.
IMPORTANT In the event of discrep-
ancies between the information pro-
vided on this “Owner handbook” and
the “Log book”, consider the specifi-
cations shown in the log book only.
Respect the prescribed size to ensure
safety of the car in movement. Fit
tyres of the same make and type on
all wheels.
IMPORTANT Do not use inner tubes
with Tubeless tyres.READING TYRE MARKINGS
Example: 185/65 R 14 86 T
185= Nominal width (S, distance in
mm between sidewalls).
65= Height/width ratio (H/S) in
percentage.
R= Radial tyre.
14= Rim diameter in inches (Ø).
86Load rate (capacity).
T= Maximum speed rating.
fig. 5L0D0229m
SMALL SPARE WHEEL
Pressed steel rim Tubeless tyre.
WHEEL GEOMETRY
Toe-in measured between rims: 0 ±1
mm.
The values refer to the car in running
order.
187-205 MUSA 3ed GB 12-11-2007 11:40 Pagina 194

195
WARNING
LIGHTS AND
MESSAGES
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
Load rating (capacity)
60 = 250 kg 84 = 500 kg
61 = 257 kg 85 = 515 kg
62 = 265 kg 86 = 530 kg
63 = 272 kg 87 = 545 kg
64 = 280 kg 88 = 560 kg
65 = 290 kg 89 = 580 kg
66 = 300 kg 90 = 600 kg
67 = 307 kg 91 = 615 kg
68 = 315 kg 92 = 630 kg
69 = 325 kg 93 = 650 kg
70 = 335 kg 94 = 670 kg
71 = 345 kg 95 = 690 kg
72 = 355 kg 96 = 710 kg
73 = 365 kg 97 = 730 kg
74 = 375 kg 98 = 750 kg
75 = 387 kg 99 = 775 kg
76 = 400 kg 100 = 800 kg
77 = 412 kg 101 = 825 kg
78 = 425 kg 102 = 850 kg
79 = 437 kg 103 = 875 kg
80 = 450 kg 104 = 900 kg
81 = 462 kg 105 = 925 kg
82 = 475 kg 106 = 950 kg
83 = 487 kgMaximum speed rating
Q = up to 160 km/h.
R = up to 170 km/h.
S = up to 180 km/h.
T = up to 190 km/h.
U = up to 200 km/h.
H = up to 210 km/h.
V = up to 240 km/h.
W = up to 270 km/h.
Y = up to 300 km/h.READING RIM MARKINGS
Example:6 J x 14 ET 40
6= rim width in inches (1).
J= rim drop centre outline (side
projection where the tyre bead
rests) (2).
14= rim nominal diameter in
inches (corresponds to diame-
ter of the tyre to be mounted)
(3 = Ø).
ET= shape and number of the
“humps” (circumference relief,
holding into its seat the bead
of the Tubeless tyre on the
rim).
40= wheel camber angle (distance
between the disc/rim support-
ing plane and the wheel rim
centre line).
187-205 MUSA 3ed GB 12-11-2007 11:40 Pagina 195

200
WARNING
LIGHTS AND
MESSAGES
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
1.48V(▲)-1.416V
1155
500
940
805
1655
1000
400
75
601.3 Multijet
1200
500
940
805
1700
1000
400
75
601.9 Multijet
1275
500
1000
805
1775
1100
500
75
60
WEIGHTS
Weights (kg)
Unladen weight (with all liquids,
fuel tank filled to 90 % and
without optional equipment):
Carrying capacity (*)
including the driver:
Maximum admitted
loads (**)
– front axle:
– rear axle:
– total:
Towable loads
– trailer with brakes:
– trailer without brakes:
Maximum load on roof:
Maximum load on tow hitch
(trailer with brakes):
(*) If special equipment is fitted (sunroof, tow hitch, etc.) the unladen car weight increases, thus reducing the specified payload.
(**) Loads not to be exceeded. The driver is responsible for arranging the loads in the boot and/or on the roof so that they comply
with these limits.
(
▲) Engine provided for some versions/markets only
187-205 MUSA 3ed GB 12-11-2007 11:40 Pagina 200

PROVISIONS FOR THE PROCESSING OF A VEHICLE
AT THE END OF ITS LIFE-CYCLE
For years now Lancia has been developing its global commitment towards the safeguarding and protection of the
Environment through the continuous improvement of its production processes and the making of increasingly
more “eco friendly” products. With a view to guaranteeing the best possible service to clients in full observance of
environmental standards and in response to the obligations imposed by European Directive 2000/53/EC on end-
of-life vehicles, Lancia offers its clients the possibility to hand in their vehicle* at the end of its life span without
additional costs.
The European Directive, in fact, provides for the take-back of the vehicle without the last holder or owner of the
same incurring expenses due to the fact that the market value of the vehicle is zero or negative. In particular, in
almost all of the countries of the European Union, up until 1st January 2007, take-back of the vehicle free of
charge only applies to vehicles registered from 1 July 2002 on, while, from 2007 on, take-back will be carried out
free of charge, independently of the year of registration, provided that the vehicle still contains all its essential
component parts (especially engine and body) and is free from additional waste materials.
Our contracted network of authorised treatment facilities has been carefully selected in order to provide a quality
service to our customers by de-polluting and recycling “End of Life Vehicles” to approved environmental
standards. To find out the location of your nearest authorised treatment facility, offering free of charge take-back,
simply contact one of our dealers or refer to the Lancia web site or call the toll free number 00800 526242 00.
*
Passenger transportation vehicles to seat a max. of nine persons, having a total admissible weight of 3.5 t
206-216 MUSA 3ed GB 12-11-2007 11:40 Pagina 210