2008 INFINITI FX35 relay

REAR VIEW MONITORDI-109
< SERVICE INFORMATION >
C
DE
F
G H
I
J
L
M A
B
DI
N
O P
YES >> GO TO 2.
NO >> Check back-up lamp system. Refer to LT-116, "
Wiring Diagram - BACK/L -" in LT section.
2.CHECK REVERSE POSITION INPUT SIGNAL
With CONSULT-III
1. Select “Data Monitor” of “REARVIEW CAMERA”.
2. Operate ignition switch with “R POSI SIG” of “Data Monitor” and check operate status.
Without CONSULT-III
1. Turn ignition switch OFF.
2. Disconnect rear view camera control unit connector.
3. Turn ignition switch ON.
4. Shift A/T selector lever to R position.
5. Check voltage between rear view camera control unit harness
connector M48 terminal 4 and ground.
OK or NG
OK >> GO TO 3.
NG >> Check harness between rear view camera control unit and back-up lamp relay.
3.CHECK DISPLAY CONTROL UNIT OUTPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect rear view camera control unit connector.
3. Turn ignition switch ON.
4. Check voltage between rear view camera control unit harness connector M48 terminal 5 and ground.
OK or NG
OK >> GO TO 5.
NG >> GO TO 4.
4.CHECK DISPLAY CO NTROL UNIT CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect display control unit connector.
3. Check continuity between rear view camera control unit harness connector M48 terminal 5 and display control unit harness con-
nector M75 terminal 8.
4. Check continuity between rear view camera control unit harness connector M48 terminal 5 and ground.
OK or NG
OK >> Replace display control unit.
NG >> Repair harness or connector.
5.CHECK CONTROL 1 SIGNAL
1. Turn ignition switch OFF.
2. Connect rear view camera control unit connector. 4 – Ground : Battery voltage
SKIA5086E
5 – Ground : Approx. 5 V
SKIA7148E
5 – 8 : Continuity should exist.
5 – Ground : Continuity should not exist.
SKIA7149E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

EC-7
C
DE
F
G H
I
J
K L
M
EC A
N
O P
DTC P1574 ASCD VEHICLE SPEED SEN-
SOR ................................................................ ..
483
Component Description ....................................... ..483
On Board Diagnosis Logic ....................................483
DTC Confirmation Procedure ................................483
Diagnosis Procedure .............................................483
DTC P1715 INPUT SPEED SENSOR (TUR-
BINE REVOLUTION SENSOR) .......................
485
Description .......................................................... ..485
CONSULT-III Reference Value in Data Monitor
Mode ................................................................... ..
485
On Board Diagnosis Logic ....................................485
Diagnosis Procedure .............................................485
DTC P1805 BRAKE SWITCH ..........................486
Description .......................................................... ..486
CONSULT-III Reference Value in Data Monitor
Mode ................................................................... ..
486
On Board Diagnosis Logic ....................................486
DTC Confirmation Procedure ................................486
Wiring Diagram .....................................................487
Diagnosis Procedure .............................................488
Component Inspection ..........................................489
DTC P2100, P2103 THROTTLE CONTROL
MOTOR RELAY ...............................................
490
Component Description ....................................... ..490
CONSULT-III Reference Value in Data Monitor
Mode ................................................................... ..
490
On Board Diagnosis Logic ....................................490
DTC Confirmation Procedure ................................490
Wiring Diagram .....................................................491
Diagnosis Procedure .............................................492
DTC P2101 ELECTRIC THROTTLE CON-
TROL FUNCTION ........................................... ..
494
Description .......................................................... ..494
On Board Diagnosis Logic ....................................494
DTC Confirmation Procedure ................................494
Wiring Diagram .....................................................495
Diagnosis Procedure .............................................496
Component Inspection ..........................................499
Removal and Installation .......................................499
DTC P2118 THROTTLE CONTROL MOTOR ..500
Component Description .........................................500
On Board Diagnosis Logic ....................................500
DTC Confirmation Procedure ................................500
Wiring Diagram .....................................................501
Diagnosis Procedure .............................................502
Component Inspection ..........................................503
Removal and Installation .......................................503
DTC P2119 ELECTRIC THROTTLE CON-
TROL ACTUATOR ...........................................
504
Component Description ....................................... ..504
On Board Diagnosis Logic ....................................504
DTC Confirmation Procedure ................................504
Diagnosis Procedure .............................................505
DTC P2122, P2123 APP SENSOR .................506
Component Description ....................................... ..506
CONSULT-III Reference Value in Data Monitor
Mode ......................................................................
506
On Board Diagnosis Logic .....................................506
DTC Confirmation Procedure ................................507
Wiring Diagram ......................................................508
Diagnosis Procedure .............................................509
Component Inspection ...........................................511
Removal and Installation .......................................511
DTC P2127, P2128 APP SENSOR .................512
Component Description .........................................512
CONSULT-III Reference Value in Data Monitor
Mode ......................................................................
512
On Board Diagnosis Logic .....................................512
DTC Confirmation Procedure ................................512
Wiring Diagram ......................................................513
Diagnosis Procedure .............................................514
Component Inspection ...........................................517
Removal and Installation .......................................517
DTC P2135 TP SENSOR ................................518
Component Description .........................................518
CONSULT-III Reference Value in Data Monitor
Mode ......................................................................
518
On Board Diagnosis Logic .....................................518
DTC Confirmation Procedure ................................518
Wiring Diagram ......................................................519
Diagnosis Procedure .............................................520
Component Inspection ...........................................522
Removal and Installation .......................................523
DTC P2138 APP SENSOR .............................524
Component Description .........................................524
CONSULT-III Reference Value in Data Monitor
Mode ......................................................................
524
On Board Diagnosis Logic .....................................524
DTC Confirmation Procedure ................................525
Wiring Diagram ......................................................526
Diagnosis Procedure .............................................527
Component Inspection ...........................................530
Removal and Installation .......................................531
DTC P2A00, P2A03 A/F SENSOR 1 ..............532
Component Description .........................................532
CONSULT-III Reference Value in Data Monitor
Mode ......................................................................
532
On Board Diagnosis Logic .....................................532
DTC Confirmation Procedure ................................532
Wiring Diagram ......................................................534
Diagnosis Procedure .............................................537
Removal and Installation .......................................541
ASCD BRAKE SWITCH ..................................542
Component Description .........................................542
CONSULT-III Reference Value in Data Monitor
Mode ......................................................................
542
Wiring Diagram ......................................................543
Diagnosis Procedure .............................................544
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

EC-14
DTC Confirmation Procedure ..............................1045
Diagnosis Procedure ...........................................1045
DTC P1564 ICC STEERING SWITCH ............1047
Component Description .......................................1047
CONSULT-III Reference Value in Data Monitor
Mode ....................................................................
1047
On Board Diagnosis Logic ...................................1047
DTC Confirmation Procedure ..............................1048
Wiring Diagram ....................................................1049
Diagnosis Procedure ...........................................1050
Component Inspection .........................................1052
DTC P1564 ASCD STEERING SWITCH ........1053
Component Description .......................................1053
CONSULT-III Reference Va lue in Data Monitor
Mode ....................................................................
1053
On Board Diagnosis Logic ...................................1053
DTC Confirmation Procedure ..............................1054
Wiring Diagram ....................................................1055
Diagnosis Procedure ...........................................1056
Component Inspection .........................................1058
DTC P1568 ICC FUNCTION ...........................1059
On Board Diagnosis Logic ...................................1059
DTC Confirmation Procedure ..............................1059
Diagnosis Procedure ...........................................1059
DTC P1572 ICC BRAKE SWITCH .................1060
Component Description .......................................1060
CONSULT-III Reference Va lue in Data Monitor
Mode ....................................................................
1060
On Board Diagnosis Logic ...................................1060
DTC Confirmation Procedure ..............................1060
Wiring Diagram ....................................................1062
Diagnosis Procedure ...........................................1063
Component Inspection .........................................1067
DTC P1572 ASCD BRAKE SWITCH .............1068
Component Description .......................................1068
CONSULT-III Reference Va lue in Data Monitor
Mode ....................................................................
1068
On Board Diagnosis Logic ...................................1068
DTC Confirmation Procedure ..............................1068
Wiring Diagram ....................................................1070
Diagnosis Procedure ...........................................1071
Component Inspection .........................................1074
DTC P1574 ICC VEHICLE SPEED SENSOR 1075
Component Description .......................................1075
On Board Diagnosis Logic ...................................1075
DTC Confirmation Procedure ..............................1075
Diagnosis Procedure ...........................................1075
DTC P1574 ASCD VEHICLE SPEED SEN-
SOR .................................................................
1077
Component Description .......................................1077
On Board Diagnosis Logic ...................................1077
DTC Confirmation Procedure ..............................1077
Diagnosis Procedure ...........................................1077
DTC P1715 INPUT SPEED SENSOR (TUR-
BINE REVOLUTION SENSOR) ......................
1079
Description ...........................................................1079
CONSULT-III Reference Value in Data Monitor
Mode ....................................................................
1079
On Board Diagnosis Logic ...................................1079
Diagnosis Procedure ............................................1079
DTC P1800 VIAS CONTROL SOLENOID
VALVE ............................................................
1080
Component Description .......................................1080
CONSULT-III Reference Value in Data Monitor
Mode ....................................................................
1080
On Board Diagnosis Logic ...................................1080
DTC Confirmation Procedure ...............................1080
Wiring Diagram ....................................................1081
Diagnosis Procedure ............................................1082
Component Inspection .........................................1083
Removal and Installation ......................................1083
DTC P1805 BRAKE SWITCH ........................1084
Description ...........................................................1084
CONSULT-III Reference Value in Data Monitor
Mode ....................................................................
1084
On Board Diagnosis Logic ...................................1084
DTC Confirmation Procedure ...............................1084
Wiring Diagram ....................................................1085
Diagnosis Procedure ............................................1086
Component Inspection .........................................1087
DTC P2100, P2103 THROTTLE CONTROL
MOTOR RELAY ..............................................
1088
Component Description .......................................1088
CONSULT-III Reference Value in Data Monitor
Mode ....................................................................
1088
On Board Diagnosis Logic ...................................1088
DTC Confirmation Procedure ...............................1088
Wiring Diagram ....................................................1089
Diagnosis Procedure ............................................1090
DTC P2101 ELECTRIC THROTTLE CON-
TROL FUNCTIO N ...........................................
1092
Description ...........................................................1092
On Board Diagnosis Logic ...................................1092
DTC Confirmation Procedure ...............................1092
Wiring Diagram ....................................................1093
Diagnosis Procedure ............................................1094
Component Inspection .........................................1097
Removal and Installation ......................................1097
DTC P2118 THROTTLE CONTROL MOTOR 1098
Component Description .......................................1098
On Board Diagnosis Logic ...................................1098
DTC Confirmation Procedure ...............................1098
Wiring Diagram ....................................................1099
Diagnosis Procedure ............................................1100
Component Inspection .........................................1101
Removal and Installation ......................................1101
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

EC-36
< SERVICE INFORMATION >[VQ35DE]
AIR CONDITIONING CUT CONTROL
AIR CONDITIONING CUT CONTROL
Input/Output Signal ChartINFOID:0000000001325899
*1: This signal is sent to the ECM through CAN communication line.
*2: ECM determines the start signal status by the signals of engine speed and battery voltage.
System DescriptionINFOID:0000000001325900
This system improves engine operati
on when the air conditioner is used.
Under the following conditions, the air conditioner is turned OFF.
 When the accelerator pedal is fully depressed.
 When cranking the engine.
 At high engine speeds.
 When the engine coolant temperature becomes excessively high.
 When operating power steering during low engine speed or low vehicle speed.
 When engine speed is excessively low.
 When refrigerant pressure is excessively low or high.
Sensor Input Signal to ECM ECM function Actuator
Air conditioner switch Air conditioner ON signal*
1
Air conditioner
cut controlAir conditio
ner relay
Accelerator pedal position sensor Accelerator pedal position
Throttle position sensor Throttle position
Crankshaft position sensor (POS)
Camshaft position sensor (PHASE)
Engine speed*2
Engine coolant temperature sensor Engine coolant temperature
Battery
Battery voltage*
2
Refrigerant pressure sensor Refrigerant pressure
Power steering pressure sensor Power steering operation
Wheel sensorVehicle speed*
1
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

ON BOARD REFUELING VAPOR RECOVERY (ORVR)EC-49
< SERVICE INFORMATION > [VQ35DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
With CONSULT-III
1. Remove fuel tank. Refer to
FL-10.
2. Drain fuel from the tank as follows:
a. Remove fuel feed hose located on the fuel gauge retainer.
b. Connect a spare fuel hose, one side to fuel gauge retainer where the hose was removed and the other side to a fuel container.
c. Drain fuel using “FUEL PUMP RELAY” in “ACTIVE TEST” mode with CONSULT-III.
3. Check refueling EVAP vapor cut valve for being stuck to close as follows. Blow air into the refueling EVAP vapor cut valv e (from the end of EVAP/ORVR line hose), and check that
the air flows freely into the tank.
4. Check refueling EVAP vapor cut valve for being stuck to open as follows.
a. Connect vacuum pump to hose end.
b. Remove fuel gauge retainer with fuel gauge unit. Always replace O-ring with new one.
c. Put fuel tank upside down.
d. Apply vacuum pressure to hose end [ −13.3 kPa ( −100 mmHg, −3.94 inHg)] with fuel gauge retainer
remaining open and check that the pressure is applicable.
Without CONSULT-III
1. Remove fuel tank. Refer to FL-10.
2. Drain fuel from the tank as follows:
a. Remove fuel gauge retainer.
b. Drain fuel from the tank using a handy pump into a fuel container.
3. Check refueling EVAP vapor cut valve for being stuck to close as follows. Blow air into the refueling EVAP vapor cut valv e (from the end of EVAP/ORVR line hose), and check that
the air flows freely into the tank.
4. Check refueling EVAP vapor cut valve for being stuck to open as follows.
a. Connect vacuum pump to hose end.
b. Remove fuel gauge retainer with fuel gauge unit. Always replace O-ring with new one.
c. Put fuel tank upside down.
PBIB1035E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

TROUBLE DIAGNOSISEC-95
< SERVICE INFORMATION > [VQ35DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
Fail-Safe ChartINFOID:0000000001325929
When the DTC listed below is detected, the EC
M enters fail-safe mode and the MIL lights up.
 When there is an open circuit on MIL circuit, the ECM c annot warn the driver by MIL lighting up when there
is malfunction on engine control system.
Therefore, when electrical controlled throttle and pa rt of ECM related diagnoses are continuously detected
as NG for 5 trips, ECM warns the driver that engi ne control system malfunctions and MIL circuit is open by
means of operating fail-safe function.
The fail-safe function also operates when above diagnos es except MIL circuit are detected and demands the
driver to repair the malfunction.
DTC No. Detected items Engine operating condition in fail-safe mode
P0102
P0103 Mass air flow sensor circuit Engine speed will not rise more than 2,400 rpm due to the fuel cut.
P0117
P0118 Engine coolant tempera-
ture sensor circuit Engine coolant temperature will be determined by ECM based on the following condition.
CONSULT-III displays the engine coolant temperature decided by ECM.
Condition Engine coolant temperature decided
(CONSULT-III display)
Just as ignition switch is turned ON
or START 40
°C (104 °F)
Approx. 4 minutes or more after
engine starting. 80
°C (176 °F)
Except as shown above 40 - 80
°C (104 - 176 °F)
(Depends on the time)
When the fail-safe system for engine coolant temperature sensor is activated, the cooling
fan operates while engine is running.
P0122
P0123
P0222
P0223
P2135 Throttle position sensor The ECM controls the electric throttle control actuator in regulating the throttle opening in
order for the idle position to be within +10 degrees.
The ECM regulates the opening speed of the throttle valve to be slower than the normal
condition.
So, the acceleration will be poor.
P0643 Sensor power supply ECM stops the electric throttle control actuator control, throttle valve is maintained at a fixed opening (approx. 5 degrees) by the return spring.
P2100
P2103 Throttle control motor relay ECM stops the electric throttle control actuator control, throttle valve is maintained at a
fixed opening (approx. 5 degrees) by the return spring.
P2101 Electric th rottle control
function ECM stops the electric throttle control actuator control, throttle valve is maintained at a
fixed opening (approx. 5 degrees) by the return spring.
P2118 Throttle control motor ECM stops the electric throttle control actuator control, throttle valve is maintained at a fixed opening (approx. 5 degrees) by the return spring.
P2119 Electric thro ttle control ac-
tuator (When electric throttle control actuator does not function properly due to the return spring
malfunction:)
ECM controls the electric throttle actuator by regulating the throttle opening around the
idle position. The engine speed will not rise more than 2,000 rpm.
(When throttle valve opening angle in fail-safe mode is not in specified range:)
ECM controls the electric throttle control actuator by regulating the throttle opening to 20
degrees or less.
(When ECM detects the throttle valve is stuck open:)
While the vehicle is driving, it slows down gradually by fuel cut. After the vehicle stops, the
engine stalls.
The engine can restart in N or P position, and engine speed will not exceed 1,000 rpm or
more.
P2122
P2123
P2127
P2128
P2138 Accelerator pedal position
sensor
The ECM controls the electric throttle control actuator in regulating the throttle opening in
order for the idle position to be within +10 degrees.
The ECM regulates the opening speed of the throttle valve to be slower than the normal
condition.
So, the acceleration will be poor.
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

TROUBLE DIAGNOSISEC-109
< SERVICE INFORMATION > [VQ35DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
ECM Harness Connector Terminal LayoutINFOID:0000000001325934
ECM Terminal and Reference ValueINFOID:0000000001325935
PREPARATION
ECM is located behind the passenger side instrument lower panel.
For this inspection, remove passenger side instrument lower panel.
ECM INSPECTION TABLE
Specification data are reference values
and are measured between each terminal and ground.
Pulse signal is measured by CONSULT-III.
CAUTION:
Do not use ECM ground terminals wh en measuring input/output voltage. Doing so may result in dam-
age to the ECMs transistor. Use a ground ot her than ECM terminals, such as the ground.
PBIB3368E
PBIB1578E
TER-
MI-
NAL
NO. WIRE
COLOR ITEM CONDITION DATA (DC Voltage)
1 B ECM ground [Engine is running]
 Idle speed Body ground
2R/L A/F sensor 1 heater
(bank 1) [Engine is running]

Warm-up condition
 Idle speed Approximately 5V
3R Throttle contro
l motor relay
power supply [Ignition switch: ON] BATTERY VOLTAGE
(11 - 14V)
4L/W Throttle control motor
(Close) [Ignition switch: ON]
 Engine stopped
 Selector lever: D
 Accelerator pedal: Fully released 0 - 14V
PBIB1584E
PBIB1104E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

EC-116
< SERVICE INFORMATION >[VQ35DE]
TROUBLE DIAGNOSIS
99 G/YICC steering switch
(models with ICC system) [Ignition switch: ON]
 ICC steering switch: OFF
Approximately 4.3V
[Ignition switch: ON]
 MAIN switch: Pressed Approximately 0V
[Ignition switch: ON]
 CANCEL switch: Pressed Approximately 1.3V
[Ignition switch: ON]
 RESUME/ACCELERATE switch: Pressed Approximately 3.7V
[Ignition switch: ON]
 SET/COAST switch: Pressed Approximately 3.0V
[Ignition switch: ON]
 DISTANCE switch: Pressed Approximately 2.2V
99 G/Y ASCD steering switch
(models with ASCD system) [Ignition switch: ON]
 ASCD steering switch: OFF
Approximately 4.0V
[Ignition switch: ON]
 MAIN switch: Pressed Approximately 0V
[Ignition switch: ON]
 CANCEL switch: Pressed Approximately 1.0V
[Ignition switch: ON]
 RESUME/ACCELERATE switch: Pressed Approximately 3.0V
[Ignition switch: ON]
 SET/COAST switch: Pressed Approximately 2.0V
101 P/L Stop lamp switch [Ignition switch: OFF]
 Brake pedal: Fully released
Approximately 0V
[Ignition switch: OFF]
 Brake pedal: Slightly depressed BATTERY VOLTAGE
(11 - 14V)
102 LG/B PNP switch [Ignition switch: ON]
 Selector lever: P or N
Approximately 0V
[Ignition switch: ON]
 Except above position BATTERY VOLTAGE
(11 - 14V)
104 L/OR Throttle co ntrol motor relay[Ignition switch: OFF]
BATTERY VOLTAGE
(11 - 14V)
[Ignition switch: ON] 0 - 1.0V
106 OR Accelerator pedal position
sensor 1 [Ignition switch: ON]
 Engine stopped
 Accelerator pedal: Fully released
0.5 - 1.0V
[Ignition switch: ON]
 Engine stopped
 Accelerator pedal: Fully depressed 3.9 - 4.7V
107 PU/W Fuel tank temperature sen-
sor [Engine is running] Approximately 0 - 4.8V
Output voltage varies with fuel
tank temperature.
108 SB ICC brake switch
(models with ICC system)
ASCD brake switch
(models with ASCD system) [Ignition switch: ON]
 Brake pedal: Slightly depressed
Approximately 0V
[Ignition switch: ON]
 Brake pedal: Fully released BATTERY VOLTAGE
(11 - 14V)
109 W/L Ignition switch [Ignition switch: OFF]
0V
[Ignition switch: ON] BATTERY VOLTAGE
(11 - 14V)
TER-
MI-
NAL NO. WIRE
COLOR
ITEM CONDITION DATA (DC Voltage)
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C