2008 INFINITI FX35 ignition switch

TROUBLE DIAGNOSISAT-83
< SERVICE INFORMATION >
DE
F
G H
I
J
K L
M A
B
AT
N
O P
TCM Input/Output Signal Reference ValueINFOID:0000000001327162
A/T ASSEMBLY HARNESS CONNECTOR TERMINAL LAYOUT
TCM INSPECTION TABLE
68
Others Engine does not start
in “N” or “P” position.
Refer to
AT- 1 7 0 , "En-
gine Cannot Be Start-
ed in "P" or "N"
Position". ON vehicle
1. Ignition switch and starter
PG-3
,
SC-
8
2. A/T position AT- 2 0 7
3. PNP switchAT- 1 0 2
69Engine starts in posi-
tions other than “N” or
“P”. ON vehicle1. Ignition switch and starter
PG-3
,
SC-
8
2. A/T position AT- 2 0 7
3. PNP switchAT- 1 0 2
70 Engine stall.ON vehicle1. A/T fluid level and state
AT- 4 9
2. Engine speed signalAT- 11 2
3. Turbine revolution sensorAT- 1 0 6
4. Torque converter clutch solenoid valveAT- 1 2 4
5. CAN communication line AT- 9 4
6. Control valve with TCMAT- 2 1 5
OFF vehicle 7. Torque converter AT- 2 6 7
71Engine stalls when se-
lector lever shifted “N”
→
“D”, “R”. ON vehicle1. A/T fluid level and state
AT- 4 9
2. Engine speed signalAT- 11 2
3. Turbine revolution sensorAT- 1 0 6
4. Torque converter clutch solenoid valveAT- 1 2 4
5. CAN communication line AT- 9 4
6. Control valve with TCMAT- 2 1 5
OFF vehicle 7. Torque converter AT- 2 6 7
72Engine speed does
not return to idle.
Refer to
AT- 1 9 4 , "En-
gine Speed Does Not
Return to Idle". ON vehicle 1. A/T fluid level and state
AT- 4 9
2. Direct clutch solenoid valveAT- 1 4 7
3. Front brake solenoid valve AT- 1 4 5
4. Accelerator pedal position sensorAT- 1 3 0
5. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 1 3 7
6. CAN communication line AT- 9 4
7. Control valve with TCMAT- 2 1 5
OFF vehicle8. Front brake (brake band)
AT- 2 6 79. Direct clutchAT- 3 0 3
No. Items Symptom Condition Diagnostic Item Reference
page
SCIA1658E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

TROUBLE DIAGNOSISAT-85
< SERVICE INFORMATION >
DE
F
G H
I
J
K L
M A
B
AT
N
O P
3. Display of solenoid valves on CONSULT-III changes at t he start of shifting, while gear position is displayed
upon completion of shifting (which is computed by TCM).
Item name Condition Display value (Approx.)
ATF TEMP SE 1 0°C (32 °F) − 20 °C (68 °F) − 80 °C (176 °F) 3.3
− 2.7 − 0.9 V
ATF TEMP SE 2 3.3 − 2.5 − 0.7 V
ATF TEMP 1 Ignition switch ON Measured ATF temperature is dis-
played.
TCC SOLENOID Lock-up is active 0.4 − 0.6 A
SLCT LVR POSI Selector lever in “N
” and “P” positions. N/P
Selector lever in “R” position. R
Selector lever in “D” position. D
VHCL/S SE-A/T During driving Approximately matches the speedom-
eter reading.
VEHICLE SPEED During driving Approximately matches the speedom-
eter reading.
ENGINE SPEED Engine running Closely matches the tachometer read-
ing.
LINE PRES SOL During driving 0.2 − 0.6 A
TURBINE REV During driving (lock-up ON) Approximately matches the engine
speed.
VHCL/S SE-MTR During driving Approximately matches the speedom-
eter reading.
ATF PRES SW 2 Low coast brake engaged. Refer to
AT- 1 8
.ON
Low coast brake disengaged. Refer to AT- 1 8
. OFF
I/C SOLENOID Input clutch disengaged. Refer to
AT- 1 8
.0.6 − 0.8 A
Input clutch engaged. Refer to AT- 1 8
.0 − 0.05 A
FR/B SOLENOID Front brake engaged. Refer to
AT- 1 8
.0.6 − 0.8 A
Front brake disengaged. Refer to AT- 1 8
. 0 − 0.05 A
D/C SOLENOID Direct clutch disengaged. Refer to
AT- 1 8
.0.6 − 0.8 A
Direct clutch engaged. Refer to AT- 1 8
.0 − 0.05 A
HLR/C SOL High and low reverse clutch disengaged. Refer to
AT- 1 8
.0.6 − 0.8 A
High and low reverse clutch engaged. Refer to AT- 1 8
.0 − 0.05 A
ON OFF SOL Low coast brake engaged. Refer to
AT- 1 8
.ON
Low coast brake disengaged. Refer to AT- 1 8
.OFF
MANU MODE SW Manual shift gate position (neutral) ON
Other than the above OFF
NON M-MODE SW Manual shift gate position OFF
Other than the above ON
UP SW LEVER Selector lever: + side ON
Other than the above OFF
DOWN SW LEVER Selector lever: - side ON
Other than the above OFF
STARTER RELAY Selector lever in “N
” and “P” positions. ON
Selector lever in other positions. OFF
ACCELE POSI Released accelerator pedal. 0.0/8
Fully depressed accelerator pedal. 8.0/8
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

AT-86
< SERVICE INFORMATION >
TROUBLE DIAGNOSIS
SELF-DIAGNOSTIC RESULT MODE
After performing “SELF-DIAGNOSTIC RESULT MODE”, place check marks for results on the AT-42, "How to
Perform Trouble Diagnosis for Quick and Accurate Repair". Reference pages are provided following the items.
Display Items List
X: Applicable, —: Not applicable
CLSD THL POSReleased accelerator pedal. ON
Fully depressed accelerator pedal. OFF
W/O THL POS Fully depressed accelerator pedal. ON
Released accelerator pedal. OFF
BRAKE SW Depressed brake pedal. ON.
Released brake pedal. OFF
GEAR During driving. 1,2,3,4,5, Item name Condition Display value (Approx.)
Items (CONSULT-
III screen terms) Malfunction is detected when... TCM self-di-
agnosis OBD-II
(DTC)
Reference page
“TRANS-
MISSION”
with CON- SULT-III MIL indica-
tor lamp(*1),
“ENGINE”
with CON-
SULT-III or GST
CAN COMM CIR-
CUIT When TCM is not transmitting or receiving CAN communication sig-
nal for 2 seconds or more.
U1000 U1000
AT- 9 4
STARTER RELAY/
CIRCIf this signal is ON other than in “P” or “N” position, this is judged to
be a malfunction.
(And if it is OFF in “P” or “N” position, this too is judged to be a mal-
function.)
P0615 —
AT- 9 7
TCM TCM is malfunctioning. P0700 P0700 AT- 1 0 1
PNP SW/CIRC PNP switch 1-4 signals input with impossible pattern.
 “P” position is detected from “N” position without any other posi-
tion being detected in between. P0705 P0705
AT- 1 0 2
TURBINE REV S/
CIRC TCM does not receive the proper voltage signal from the sensor.
 TCM detects an irregularity only at position of 4th gear for turbine
revolution sensor 2. P0717 P0717
AT- 1 0 6
VEH SPD SEN/CIR
AT  Signal from vehicle speed sensor A/T (Revolution sensor) not in-
put due to cut line or the like.
 Unexpected signal input during running.
 After ignition switch is turned ON, unexpected signal input from vehicle speed sensor MTR before the vehicle starts moving. P0720 P0720
AT- 1 0 8
ENGINE SPEED
SIGTCM does not receive the CAN communication signal from the
ECM.
P0725 P0725
AT- 11 2
A/T 1ST GR
FNCTNA/T cannot shift to 1st gear. P0731 P0731
AT- 11 4
A/T 2ND GR
FNCTNA/T cannot shift to 2nd gear. P0732 P0732
AT- 11 6
A/T 3RD GR
FNCTNA/T cannot shift to 3rd gear. P0733 P0733
AT- 11 8
A/T 4TH GR
FNCTNA/T cannot shift to 4th gear. P0734 P0734
AT- 1 2 0
A/T 5TH GR
FNCTNA/T cannot shift to 5th gear. P0735 P0735
AT- 1 2 2
TCC SOLENOID/
CIRCNormal voltage not applied to solenoid due to cut line, short, or the
like.
P0740 P0740
AT- 1 2 4
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

TROUBLE DIAGNOSISAT-91
< SERVICE INFORMATION >
DE
F
G H
I
J
K L
M A
B
AT
N
O P
DTC WORK SUPPORT MODE
Display Items List
Diagnosis Procedure without CONSULT-IIIINFOID:0000000001327164
OBD-II SELF-DIAGNOSTIC PROCEDURE (WITH GST)
Refer to EC-125, "Generic Scan Tool (GST) Function" (for VQ35DE) or EC-704, "Generic Scan Tool (GST)
Function" (for VK45DE).
OBD-II SELF-DIAGNOSTIC PROCEDURE (NO TOOLS)
Refer to EC-71, "Malfunction Indicator Lamp (MIL)" (for VQ35DE) or EC-649, "Malfunction Indicator Lamp
(MIL)" (for VK45DE).
TCM SELF-DIAGNOSTIC PROCEDURE (NO TOOLS)
Description
When the ignition switch is turned ON, the indicator la mp lights up for 2 seconds. As a method for locating the
suspect circuit, when the self-diagnostics start signal is input, the memory for the malfunction location is output
and the A/T CHECK indicator lamp flashes to display the corresponding DTC.
Diagnostic Procedure
Voltage (V) — — Displays the value measured by the voltage
probe.
Frequency (Hz) — —
The value measured by the pulse probe is dis-
played.
DUTY-HI (high) (%) — —
DUTY-LOW (low) (%) — —
PLS WIDTH-HI (ms) — —
PLS WIDTH-LOW (ms) — — Monitored item (Unit)
Select Monitor Item
Remarks
ECU IN-
PUT SIG- NALS MAIN SIG-
NALS SELEC-
TION
FROM
MENU
DTC work support item Description Check item
1ST GR FUNCTN P0731 Following items for “1st gear function” can be confirmed.
 Self-diagnosis status (whether the diagnosis is being performed
or not)
 Self-diagnostic results (OK or NG)
 Input clutch solenoid valve
 Front brake solenoid valve
 Direct clutch solenoid valve
 High and low reverse clutch solenoid valve
 Each clutch
 Hydraulic control circuit
2ND GR FUNCTN P0732
Following items for “2nd gear function” can be confirmed.
 Self-diagnosis status (whether the diagnosis is being performed
or not)
 Self-diagnostic results (OK or NG)
3RD GR FUNCTN P0733 Following items for “3rd gear function” can be confirmed.
 Self-diagnosis status (whether the diagnosis is being performed
or not)
 Self-diagnostic results (OK or NG)
4TH GR FUNCTN P0734 Following items for “4th gear function” can be confirmed.
 Self-diagnosis status (whether the diagnosis is being performed
or not)
 Self-diagnostic results (OK or NG)
5TH GR FUNCTN P0735 Following items for “5th gear function” can be confirmed.
 Self-diagnosis status (whether the diagnosis is being performed
or not)
 Self-diagnostic results (OK or NG)
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

AT-92
< SERVICE INFORMATION >
TROUBLE DIAGNOSIS
1.CHECK A/T CHECK INDICATOR LAMP
1. Start the engine with selector lever in “P” pos ition. Warm engine to normal operating temperature.
2. Turn ignition switch ON and OFF at least twice, then leave it in the OFF position.
3. Wait 10 seconds.
4. Turn ignition switch ON. (Do not start engine.)
Does A/T CHECK indicator lamp come on for about 2 seconds?
YES >> GO TO 2.
NO >> Go to AT-170, "
A/T Check Indicator Lamp Does Not Come On".
2.JUDGEMENT PROCEDURE
1. Turn ignition switch OFF.
2. Keep pressing shift lock release button.
3. Move selector lever from “P” to “D” position.
4. Release accelerator pedal. (Set the closed throttle position signal ON.)
5. Depress brake pedal. (Stop lamp switch signal ON.)
6. Turn ignition switch ON. (Do not start engine.)
7. Wait 3 seconds.
8. Move the selector lever to the manual shift gate side. (Manual mode signal ON.)
9. Release brake pedal. (Stop lamp switch signal OFF.)
10. Move the selector lever to “D” position. (Manual mode signal OFF.)
11. Depress brake pedal. (Stop lamp switch signal ON.)
12. Release brake pedal. (Stop lamp switch signal OFF.)
13. Depress accelerator pedal fully and release it.
>> GO TO 3.
3.CHECK SELF-DIAGNOSIS CODE
Check A/T CHECK indicator lamp. Refer to "Judgement Self-diagnosis Code".
If the system does not go into self-diagnostics. Refer to AT-102
, AT-155, AT-164, AT-165.
>> DIAGNOSIS END
Judgement Self-diagnosis Code
If there is a malfunction, the lamp lights up fo r the time corresponding to the suspect circuit.
No. Malfunctioning item No. Malfunctioning item
1 Revolution sensor AT- 1 0 8
12 A/T interlock AT- 1 3 9
2 Direct clutch solenoid valve AT- 1 4 713 A/T 1st engine braking AT-141
3 Torque converter clutch solenoid valve AT- 1 2 4, AT- 1 2 614 Start signal AT- 9 7
4 Line pressure solenoid valve AT- 1 2 815 Accelerator pedal position sensor AT- 1 3 0
5 Input clutch solenoid valve AT- 1 4 316 Engine speed signal AT- 11 2
6 Front brake solenoid valve AT- 1 4 517 CAN communication line AT- 9 4
7 Low coast brake solenoid valve AT- 1 5 1, AT- 1 5 318 1st gear function AT- 11 4
8 High and low reverse clutch solenoid valve AT- 1 4 919 2nd gear function AT- 11 6
9 PNP switch AT- 1 0 220 3rd gear function AT- 11 8
10 A/T fluid temperature sensor AT-13221 4th gear function AT- 1 2 0
11 Turbine revolution sensor AT- 1 0 622 5th gear function AT- 1 2 2
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

TROUBLE DIAGNOSISAT-93
< SERVICE INFORMATION >
DE
F
G H
I
J
K L
M A
B
AT
N
O P
Erase Self-diagnosis
 In order to make it easier to find the cause of
hard-to-duplicate malfunctions, malfunction information is
stored into the control unit as necessary during use by the user. This memory is not erased no matter how
many times the ignition switch is turned ON and OFF.
 However, this information is erased by turning igni tion switch “OFF” after performing self-diagnostics or by
erasing the memory using the CONSULT-III.
SCIA8153E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

AT-94
< SERVICE INFORMATION >
DTC U1000 CAN COMMUNICATION LINE
DTC U1000 CAN COMMUNICATION LINE
DescriptionINFOID:0000000001327165
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent malfunction detection ability.
Many electronic control units are equipped onto a vehi cle, and each control unit shares information and links
with other control units during operation (not independent ). In CAN communication, control units are con-
nected with 2 communication lines (CAN-H line, CAN-L line) allowing a high rate of information transmission
with less wiring. Each control unit transmits/recei ves data but selectively reads required data only.
On Board Diagnosis LogicINFOID:0000000001327166
Diagnostic trouble code “U1000 CAN COMM CIRCUIT” with CONSULT-III or 17th judgement flicker without
CONSULT-III is detected when TCM cannot communicate to other control units.
Possible CauseINFOID:0000000001327167
Harness or connectors
(CAN communication line is open or shorted.)
DTC Confirmation ProcedureINFOID:0000000001327168
NOTE:
If “DTC Confirmation Procedure” has been previously performed, alw ays turn ignition switch OFF and
wait at least 10 seconds before performing the next test.
After the repair, perform the following proc edure to confirm the malfunction is eliminated.
WITH CONSULT-III
1. Turn ignition switch ON.
2. Select “ECU INPUT SIGNALS” or “MAIN SIGNAL S” in “DATA MONITOR” mode for “TRANSMISSION”
with CONSULT-III.
3. Start engine and wait for at least 6 seconds.
4. If DTC is detected, go to AT-96, "
Diagnosis Procedure".
WITH GST
Follow the procedure “WITH CONSULT-III”.
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

AT-96
< SERVICE INFORMATION >
DTC U1000 CAN COMMUNICATION LINE
TCM terminals and data are reference value. Measured betwe en each terminal and ground.
Diagnosis ProcedureINFOID:0000000001327170
1.CHECK CAN COMMUNICATION CIRCUIT
With CONSULT-III1. Turn ignition switch ON and start engine.
2. Select “SELF-DIAG RESULTS” mode fo r “TRANSMISSION” with CONSULT-III.
Is the
“U1000 CAN COMM CIRCUIT” indicated?
YES >> Go to LAN section. Refer to LAN-43, "CAN System Specification Chart".
NO >> INSPECTION END
Te r m i n a l Wire
color Item Condition Data (Approx.)
3 L CAN-H – –
8 P CAN-L – –
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C