2008 INFINITI FX35 shaft

ON-VEHICLE SERVICEAT-227
< SERVICE INFORMATION >
DE
F
G H
I
J
K L
M A
B
AT
N
O P
1. Drain ATF through drain plug.
2. Remove exhaust front tube and center muffler with power tool. Refer to EX-3, "
Component".
3. Remove rear propeller shaft. Refer to PR-9, "
Removal and Installation".
4. Remove control rod. Refer to AT-206, "
Control Rod Removal and Installation".
5. Support A/T assembly with a transmission jack. CAUTION:
When setting transmission jack, be careful not to allow it to collide against the drain plug.
6. Remove rear engine mounting member with power tool. Refer to AT-241, "
Removal and Installation (2WD
Models)".
7. Remove engine mounting insulator (rear). Refer to AT-241, "
Removal and Installation (2WD Models)".
8. Remove tightening bolts for rear extension assembly and trans- mission case.
9. Tap rear extension assembly with soft hammer.
10. Remove rear extension assembly from transmission case. (With needle bearing.)
11. Remove bearing race from output shaft.
SCIA6941E
SCIA3432E
SCIA3431E
SCIA5245E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

AT-228
< SERVICE INFORMATION >
ON-VEHICLE SERVICE
12. Remove output shaft from transmission case by rotating left/right.
13. Remove parking gear from output shaft.
14. Remove seal rings from output shaft.
15. Remove needle bearing from rear extension.
16. Remove parking actuator support from rear extension.
SCIA5246E
SCIA5247E
SCIA5209E
SCIA6021E
SCIA3423E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

ON-VEHICLE SERVICEAT-229
< SERVICE INFORMATION >
DE
F
G H
I
J
K L
M A
B
AT
N
O P
17. Remove parking pawl (with return spring) and pawl shaft from rear extension.
18. Remove return spring from parking pawl.
19. Remove rear oil seal from rear extension. CAUTION:
Be careful not to scratch rear extension.
INSPECTION
 If the contact surface on parking actuator support, parking pawl,etc. has excessive wear, abrasion, bend, or any other damage,
replace the components.
SCIA3424E
SCIA2445E
SCIA3524E
SCIA5143E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

AT-230
< SERVICE INFORMATION >
ON-VEHICLE SERVICE
INSTALLATION
CAUTION:
After completing installation, check A/T position, A/T fluid leakage and A/F fluid level. Refer to AT-207,
"Checking of A/T Position", AT- 11 , "Checking A/T Fluid".
1. As shown in the figure, use a drift to drive rear oil seal into the rear extension until it is flush.
CAUTION:
 Do not reuse rear oil seal.
 Apply ATF to rear oil seal.
2. Install return spring to parking pawl.
3. Install parking pawl (with return spring) and pawl shaft to rear extension.
SCIA5144E
SCIA5311E
SCIA2445E
SCIA3424E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

ON-VEHICLE SERVICEAT-231
< SERVICE INFORMATION >
DE
F
G H
I
J
K L
M A
B
AT
N
O P
4. Install parking actuator support to rear extension.
5. Install needle bearing to rear extension. CAUTION:
 Take care with the direction of needle bearing. Refer to
AT-264, "
Location of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings".
 Apply petroleum jelly to needle bearing.
6. Install seal rings in output shaft. CAUTION:
 Do not reuse seal rings.
 Apply petroleum jelly to seal rings.
7. Install parking gear to output shaft
8. Install output shaft to transmission case.
SCIA3423E
SCIA6021E
SCIA5209E
SCIA5247E
SCIA5246E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

AT-232
< SERVICE INFORMATION >
ON-VEHICLE SERVICE
9. Install bearing race to output shaft.
10. Apply recommended sealant (Genuine Anaerobic Liquid Gasketor equivalent. Refer to GI-44, "
Recommended Chemical Product
and Sealant".) to rear extension assembly as shown in the fig-
ure.
CAUTION:
Completely remove all moisture, oil and old sealant, etc.
from the transmission case and rear extension assembly
mounting surfaces.
11. Install rear extension assembly to transmission case. (With nee- dle bearing.)
CAUTION:
Insert the tip of parking rod between the parking pawl and
the parking actuator support when assembling the rear
extension assembly.
12. Tighten rear extension assembly mounting bolts to specified torque. Refer to "COMPONENTS".
CAUTION:
Do not reuse self-sealing bolts.
13. Install engine mounting insulator (rear). Refer to AT-241, "
Removal and Installation (2WD Models)".
14. Install rear engine mounting member. Refer to AT-241, "
Removal and Installation (2WD Models)".
15. Install control rod. Refer to AT-206, "
Control Rod Removal and Installation".
16. Install rear propeller shaft. Refer to PR-9, "
Removal and Installation".
17. Install exhaust front tube and center muffler. Refer to EX-3, "
Component".
18. Install drain plug in oil pan, and then tighten drain plug to the specified torque. Refer to AT-215, "
Control
Valve with TCM and A/T Fluid Temperature Sensor 2".
CAUTION:
Do not reuse drain plug gasket.
19. Pour ATF into A/T assembly. Refer to AT- 11 , "
Changing A/T Fluid".
SCIA5245E
SCIA8228E
SCIA3431E
SCIA6941E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

ON-VEHICLE SERVICEAT-233
< SERVICE INFORMATION >
DE
F
G H
I
J
K L
M A
B
AT
N
O P
Rear Oil SealINFOID:0000000001327395
REMOVAL
1. Remove center muffler with power tool. Refer to EX-3, "Compo-
nent".
2. Remove rear propeller shaft. Refer to PR-9, "
Removal and
Installation".
3. Remove front propeller shaft (AWD models). Refer to PR-4,
"Removal and Installation".
4. Remove transfer assembly from A/T assembly (AWD models). Refer to TF-40, "
Removal and Installation".
5. Remove rear oil seal using a flat-bladed screwdriver. CAUTION:
Be careful not to scratch rear extension assembly (2WD
models) or adapter case assembly (AWD models).
INSTALLATION
CAUTION:
After completing installati on, check A/T fluid leakage and A/T fluid level. Refer to AT- 11 , "
Checking A/T
Fluid".
1. As shown in the figure, use the drift to drive rear oil seal into rear extension assembly (2WD models) or adapter case assembly
(AWD models) until it is flush.
CAUTION:
 Do not reuse rear oil seal.
 Apply ATF to rear oil seal.
2. Install transfer assembly to A/T assembly (AWD models). Refer to TF-40, "
Removal and Installation".
3. Install front propeller shaft (AWD models). Refer to PR-4,
"Removal and Installation".
4. Install rear propeller shaft. Refer to PR-9, "
Removal and Installa-
tion".
5. Install center muffler. Refer to EX-3, "
Component".
Revolution Sensor Component (2WD Models Only)INFOID:0000000001327396
COMPONENTS
SCIA5410E
SCIA5411E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C

AT-234
< SERVICE INFORMATION >
ON-VEHICLE SERVICE
REMOVAL
1. Disconnect the battery cable from the negative terminal.
2. Drain ATF through drain plug.
3. Remove front cross bar. Refer to FSU-6, "
Removal and Installation".
4. Remove exhaust front tube and center muffler with power tool. Refer to EX-3, "
Component".
5. Remove rear propeller shaft. Refer to PR-9, "
Removal and Installation".
6. Remove control rod. Refer to AT-206, "
Control Rod Removal and Installation".
7. Remove clips (1), oil pan (2) and oil pan gasket.  : Vehicle front
 : Bolt (22)
 Drain plug (3)
1. Rear extension 2. A/T 3. Oil pan gasket
4. Clip 5. Oil pan mounting bolt 6. Oil pan
7. Drain plug 8. Drain plug gasket 9. Revolution sensor
10. Self-sealing bolt
Refer to GI section to make sure icons (symbol marks) in the figure. Refer to GI-8, "
Component".
However, refer to the following symbol for others.
*: Apply Genuine Anaerobic Liquid Gasket or equivalent. Refer to GI-44, "Recommended Chemical Product and Sealant"
SCIA8043E
SCIA8117E
3AA93ABC3ACD3AC03ACA3AC03AC63AC53A913A773A893A873A873A8E3A773A983AC73AC93AC03AC3
3A893A873A873A8F3A773A9D3AAF3A8A3A8C3A863A9D3AAF3A8B3A8C