2008 GEELY MK suspension

Section 3 LH/RH Rear Suspension Coil SpringReplacement1. Remove rear wheel
2. Remove the wire of the wheel speed sensor(with ABS)
(1) Remove the connector of wheel speed sensor.
(2) Remove bolts and wheel speed sensor from rear axle
frame.
Notes:
Remove the right sensor wire by using same process as left.
3. Remove the load-sensing valve bracket (without ABS)
Remove two nuts and load-sensing valve bracket from the axle
bracket
4. Remove the proportioning valve and rear right brake tube
(1) Remove the proportioning valve and rear right brake tube by
the special tool
(2) Remove the clips
Notes: Don't reuse the clips
5. Remove the proportioning valve and rear left brake tube
Notes: use the same operations of the proportioning valve and
rear right brake tube to remove #3 rear brake tube.
6. Remove right parking brake cable assembly
Remove nuts and right parking brake cable assembly
assembly from rear axle frame
7. Remove left parking brake cable assembly
8. Loose the rear axle assembly
Loose two 2 boltsRear Suspension System-LH/RH Rear Suspension Coil Spring4-57

9. Remove the left rear shock absorber assembly
(1) Lift the rear axle at left sustainer by lifting jack
(2) Remove nuts, washers and left rear shock absorber assembly
10. Remove right rear shock absorber assembly
Notes: Remove right rear shock absorber assembly by using same
operations as left.
11. Remove left rear helical spring
Slowly lower lifting jack, remove helical spring and upper pads
and lower pads
12. Mount the left rear helical spring
(1) Mount the upper pad, let gap right on the helical spring.
(2) Mount lower pad, let and load the left helical sprig into the rear
axle.
13. Temporarily tighten the left rear shock absorber assembly
(1) Mount the left rear shock absorber onto rear axle frame when
lift jack.
(2) Temporarily tighten nut and washer.
14. Temporarily tighten the right rear shock absorber assembly.
Notes: Mount the right assembly by using same operations as left.
15. Mount right parking brake cable assembly
Mount right parking brake cable assembly by nuts
Torque: 5.4 N.m
16. Mount left parking brake cable assembly.
Tips: Mount the right assembly by using same operations as left.
17. Mount the proportioning valve and rear right brake tube
(1) Connect the brake hose with brake tube by special tool.
Torque: 1 5 N.m
(2) Mount clipsRear Suspension System-LH/RH Rear Suspension Coil Spring4-58

Rear Suspension System-LH/RH Rear Suspension Coil Spring4-5918. Mount rear right brake tube
Tips:
Mount the right assembly by using same operations as left.
19. Mount sideslip control sensor wire (with ABS)
(1) Tighten sideslip control sensor wire by bolts
Torque: 8.0 N.m
(2) Mount sideslip control sensor wire
Attention: Mount the right wire by using same operations as left.
20. Mount load-sensing valve bracket (without ABS)
Mount load-sensing valve bracket by two buts
21. Sufficiently tighten the rear axle frame assembly
(1) Stabilize the shock absorber assembly
Use the lifting jack and add 90Kg force on rear luggage
carrier if bolts can not be tightened at this point.
(2) Sufficiently tighten bolts
Torque: 82 N.m
22. Sufficiently tighten the left rear shock absorber assembly
Sufficiently tighten nuts
Torque: 49 N.m
23. Sufficiently tighten the right rear shock absorber assembly
Tips: Mount the right rear shock absorber by using same opera-
tions as left.
24. Release the air in the brake hose
25. Mount the rear wheel
Torque: 103 N.m
26. Check rear the wheel alignment
27. Check the wheel speed sensor signal of ABS( with ABS)

Section 4 Rear Absorber Installation AssemblyComponent ViewReplacement1. Remove the rear seat cushion assembly
2. Remove divided rear seat back assembly
3. Remove LH & RH rear seat back hinge (2 pieces)
4. Remove rear seat belt assembly
5. Remove left rear door moldingUpper suspension carrier
Rear vibration cushion
Shock absorber upper cover WasherLeft rear shock absorber assemblyRear Suspension System-Rear Absorber Installation Assembly4-60specified torqueN.
m :washer

Rear Suspension System-Rear Absorber Installation Assembly4-616. Remove rear left lower pillar interior panel
7. Remove the lower rear shelf interior panel
8. Remove rear left upper pillar interior pane
9. Remove rear right lower pillar interior pane
10. Remove the high brake lamp
11. Remove the rear shelf interior panel
12. Remove rear wheel
13. Remove the rear left shock absorber assembly
(1)Lift the rear axle frame by lifting jack (see right figure)
(2)Remove two nuts by clamping the piston push rod
(3)move the washer and upper suspension bracket
(4) Remove nut, washer and left rear shock absorber assembly
(5) Remove shock absorber upper cover
14. Check rear left shock absorber assembly
Check the abnormal resistance and noise in the operation by
compressing and extending the push rod, replace it if any abnormal.
15.Mount rear left shock absorber assembly
(1) Mount shock absorber upper cover
(2) Mount shock absorber, upper suspension bracket and washer
onto vehicle body
(3) After clamp piston push rod, mount lower nut and let piston
push rod higher 15-18mm than nut (see right figure)
(4) Mount upper nut according lower nut
Torque: 25N.m
(5) Mount shock absorber onto rear axle frame by washer and nut
at lifting jack
Torque: 49N.m
16. Mount rear wheel
Torque: 103N.m
17. Check rear wheel alignment

Section 5 Rear Suspension CrossmemberComponent ViewRear shock absorber subassembly
Upper washer
Left rear helical spring
Lower washer
Rear right support bushingLower washer Right rear helical springUpper washer
Rear suspension
crossmentber
Rear left support bushing
Parking brake cable assembly Load-sensing valve bracket without
ABSRear Suspension System-Rear Suspension Crossmember4-62specified torqueN.
m :Wheel speed sensor wire
Bracket with ABS
Brake hose
Rear brake drum
subassembly
Right rear hub and
bearing subassembly
Rear brake drum
subassembly Rear brake assembly Brake hose
Left rear hub&bearing
subassembly Clamp
Rear stabilizer
bar bushing
Non-reusable parts

Rear Suspension System-Rear Suspension Crossmember4-63Disassemble:1. Remove rear wheel
2. Remove sideslip control sensor wire (with ABS)
3. Remove load-sensing valve bracket (without ABS)
4. Remove proportioning valve and right rear brake tube
5. Remove proportioning valve and left rear brake tube
6. Remove right parking brake cable assembly
7. Remove left parking brake cable assembly
Tips: Remove right parts by using same operations as left
8. Remove rear brake drum subassembly
9. Remove left rear hub and bearing assembly
(1) Remove nuts and right parking brake cable assembly from
rear axle frame
(2) Remove four bolts and left rear hub and bearing assembly
(3) Remove rear brake assembly from rear axle frame
10. Remove rear right hub and bearing assembly
Tips: Remove right parts by using same operations as left
11. Loosen rear axle frame assembly
12. Disassemble rear left shock absorber assembly
13. Disassemble rear right shock absorber assembly
Tips: Remove right parts by using same operations as left
14. Remove rear left helical spring
15. Remove rear right helical spring
Tips: Remove right parts by using same operations as left
16. Remove rear axle assembly
(1) Lift rear axle assembly by lifting axel
(2) Remove two bolts and rear axle frame assembly

17. Remove rear stabilizer bar bushing
18. Remove left rear axle frame bushing
(1) Bend two bushing shoulders by chisel and hand hammer
Tips: Bend bushing shoulder till hooked by special tool
(2) Remove bushing from axle by special tool
Tips: Apply protective paint if axle frame scratched
19. Remove rear right axle frame bushing
Tips: Remove right parts by using same operations as left
20. Mount rear left axle frame bushing
(1) As showed in graphic, Mount left rear axle carrier onto rear
axle frame
(2) Mount bushing onto axle frame
Tips:
fix the jaw of special tool onto bushing
Don't chafe rubber of bushing
Don't deform the shoulder of bushing
21. Mount rear right axle carrier bushing
Tips: Mount right parts by using same operations as left
22. Mount rear stabilizer bar bushing4-64Front
rubber partBending
bushing shoulderRear Suspension System-Rear Suspension Crossmember