2008 GEELY MK Brake system

Front Suspension SystemFront Strut Assembly4-46Section 4 Front Strut AssemblyReplacement1. Remove screen wiper arm cover
2. Remove right screen wiper
3. Remove left screen wiper
4. Remove hood and seals of vehicle neck
5. Remove upper right ventilation shield of vehicle neck
6. Remove upper left ventilation shield of vehicle neck
7. Remove the wiper linkage assembly of windscreen
8. Remove the hood of vehicle neck
(1) Remove the bolt and 2 clips, disconnect the harness
(2) Remove the hose and harness (wiper)
(3) Remove the 8 bolts of ventilation shield of vehicle neck
9. Remove the front wheel
10. Remove the brake hose
(1) Remove the bolts, brake hose and the clamp of ABS sensor
harness from the shock absorber bracket (with ABS)
(2) Remove the bolts and brake hose from the shock absorber
(without ABS)
11. Remove the front shock absorber with helical spring
(1) Remove the shock absorber from knuckle after remove the two
nuts and bolts.
(2) Remove the front shock absorber with helical spring, remove
the three bolts mounting suspension bracket
12. Fix the front shock absorber with helical spring
(1) Mount the two bolts and one bolt onto the bracket of shock
absorber underside, and fix it onto the vise
(2) Hold down the helical spring
Notice: Don't use the impact wrench which can damage the
special tool-

Front Suspension System-Front Strut Assembly4-4828. Mount the dust seals of left front suspension bracket
29. Mount the left front suspension bracket sub-assembly
30. Mount the front bracket onto the left front shock absorber nuts
(1) Hold the bracket by two bolts and a screwdriver or analogue.
Mount the new centre nut
Torque: 33N.m
Notice: DonÕt cause damage to the stud of suspension bracket.
(2) The special tool for remove
(3) Apply the multipurpose grease onto the suspension bracket
31. Mount the dust cap of left front suspension bracket
32. Mount the front stud assembly
(1) Mount the #2 suspension bracket
(2) Mount the front stud assembly by three nuts
Torque: 39N.m
(3) Mount the shock absorber onto the knuckle
(4) Film the engine oil onto the thread of two nuts
(5) Mount the two bolts and nuts
Torque: 132N.m
33. Mount the brake hose
Torque: 29N.m
34. Mount the front wheel
Torque: 103N.m
35. Mount the outside cover of vehicle neck
(1) Mount the outside cover of vehicle neck by 8 bolts
Torque: 5N.m
(2) Connect hose and harness (screen wiper)
(3) Mount the harness by bolts and two clips
36. Mount the linkage assembly of windshield wiper
37. Mount the ventilation hood of left vehicle neck
38. Mount the ventilation hood of right vehicle neck
39. Mount the engine hood and seals of vehicle neck
40. Mount the left front wiper arm
41. Mount the right front wiper arm
42. Check and adjust the front wheel alignmentMulti-purpose grease

Component ViewUpper washer
Left rear
helical spring
Lower washer Rear shock absorber assembly Right rear helical spring
Left rear helical spring
Lower washer829.09849Chapter 6 Rear Suspension SystemSection 1 Rear Suspension SystemLoad-sensing valve
bracketRear supension crossmemberRear Suspension System-Rear Suspension System4-54specified torqueN.
m :With ABS
Side slip control sensor wire
Washer
Clip Brake hose
Brake hoseNon-reusable parts

Section 3 LH/RH Rear Suspension Coil SpringReplacement1. Remove rear wheel
2. Remove the wire of the wheel speed sensor(with ABS)
(1) Remove the connector of wheel speed sensor.
(2) Remove bolts and wheel speed sensor from rear axle
frame.
Notes:
Remove the right sensor wire by using same process as left.
3. Remove the load-sensing valve bracket (without ABS)
Remove two nuts and load-sensing valve bracket from the axle
bracket
4. Remove the proportioning valve and rear right brake tube
(1) Remove the proportioning valve and rear right brake tube by
the special tool
(2) Remove the clips
Notes: Don't reuse the clips
5. Remove the proportioning valve and rear left brake tube
Notes: use the same operations of the proportioning valve and
rear right brake tube to remove #3 rear brake tube.
6. Remove right parking brake cable assembly
Remove nuts and right parking brake cable assembly
assembly from rear axle frame
7. Remove left parking brake cable assembly
8. Loose the rear axle assembly
Loose two 2 boltsRear Suspension System-LH/RH Rear Suspension Coil Spring4-57

9. Remove the left rear shock absorber assembly
(1) Lift the rear axle at left sustainer by lifting jack
(2) Remove nuts, washers and left rear shock absorber assembly
10. Remove right rear shock absorber assembly
Notes: Remove right rear shock absorber assembly by using same
operations as left.
11. Remove left rear helical spring
Slowly lower lifting jack, remove helical spring and upper pads
and lower pads
12. Mount the left rear helical spring
(1) Mount the upper pad, let gap right on the helical spring.
(2) Mount lower pad, let and load the left helical sprig into the rear
axle.
13. Temporarily tighten the left rear shock absorber assembly
(1) Mount the left rear shock absorber onto rear axle frame when
lift jack.
(2) Temporarily tighten nut and washer.
14. Temporarily tighten the right rear shock absorber assembly.
Notes: Mount the right assembly by using same operations as left.
15. Mount right parking brake cable assembly
Mount right parking brake cable assembly by nuts
Torque: 5.4 N.m
16. Mount left parking brake cable assembly.
Tips: Mount the right assembly by using same operations as left.
17. Mount the proportioning valve and rear right brake tube
(1) Connect the brake hose with brake tube by special tool.
Torque: 1 5 N.m
(2) Mount clipsRear Suspension System-LH/RH Rear Suspension Coil Spring4-58

Rear Suspension System-LH/RH Rear Suspension Coil Spring4-5918. Mount rear right brake tube
Tips:
Mount the right assembly by using same operations as left.
19. Mount sideslip control sensor wire (with ABS)
(1) Tighten sideslip control sensor wire by bolts
Torque: 8.0 N.m
(2) Mount sideslip control sensor wire
Attention: Mount the right wire by using same operations as left.
20. Mount load-sensing valve bracket (without ABS)
Mount load-sensing valve bracket by two buts
21. Sufficiently tighten the rear axle frame assembly
(1) Stabilize the shock absorber assembly
Use the lifting jack and add 90Kg force on rear luggage
carrier if bolts can not be tightened at this point.
(2) Sufficiently tighten bolts
Torque: 82 N.m
22. Sufficiently tighten the left rear shock absorber assembly
Sufficiently tighten nuts
Torque: 49 N.m
23. Sufficiently tighten the right rear shock absorber assembly
Tips: Mount the right rear shock absorber by using same opera-
tions as left.
24. Release the air in the brake hose
25. Mount the rear wheel
Torque: 103 N.m
26. Check rear the wheel alignment
27. Check the wheel speed sensor signal of ABS( with ABS)

Rear Suspension System-Rear Absorber Installation Assembly4-616. Remove rear left lower pillar interior panel
7. Remove the lower rear shelf interior panel
8. Remove rear left upper pillar interior pane
9. Remove rear right lower pillar interior pane
10. Remove the high brake lamp
11. Remove the rear shelf interior panel
12. Remove rear wheel
13. Remove the rear left shock absorber assembly
(1)Lift the rear axle frame by lifting jack (see right figure)
(2)Remove two nuts by clamping the piston push rod
(3)move the washer and upper suspension bracket
(4) Remove nut, washer and left rear shock absorber assembly
(5) Remove shock absorber upper cover
14. Check rear left shock absorber assembly
Check the abnormal resistance and noise in the operation by
compressing and extending the push rod, replace it if any abnormal.
15.Mount rear left shock absorber assembly
(1) Mount shock absorber upper cover
(2) Mount shock absorber, upper suspension bracket and washer
onto vehicle body
(3) After clamp piston push rod, mount lower nut and let piston
push rod higher 15-18mm than nut (see right figure)
(4) Mount upper nut according lower nut
Torque: 25N.m
(5) Mount shock absorber onto rear axle frame by washer and nut
at lifting jack
Torque: 49N.m
16. Mount rear wheel
Torque: 103N.m
17. Check rear wheel alignment

Section 5 Rear Suspension CrossmemberComponent ViewRear shock absorber subassembly
Upper washer
Left rear helical spring
Lower washer
Rear right support bushingLower washer Right rear helical springUpper washer
Rear suspension
crossmentber
Rear left support bushing
Parking brake cable assembly Load-sensing valve bracket without
ABSRear Suspension System-Rear Suspension Crossmember4-62specified torqueN.
m :Wheel speed sensor wire
Bracket with ABS
Brake hose
Rear brake drum
subassembly
Right rear hub and
bearing subassembly
Rear brake drum
subassembly Rear brake assembly Brake hose
Left rear hub&bearing
subassembly Clamp
Rear stabilizer
bar bushing
Non-reusable parts