2008 GEELY MK Brake system

Brake System -Rear Brake Drum4-1018. Remove the left brake automatic adjustment rod.
Remove the brake adjustment rod and its spring.
9. Remove the return spring of the brake shoe.
Remove the return spring from the brake shoe.
10. Remove the rear brake shoe.
(1) Prize the end cover with a special tool, and remove the set
spring and pin.
(2) Remove the parking brake cable from the parking brake
extension rod with a pair of pinchers.
11. Remove the parking brake shoe extension rod accessory.
Remove the C-washer and parking brake shoe extension rod with
screwdriver.
12. Check the thickness of the brake shoe lining.
Measure the thickness of the brake shoe lining with ruler.
Standard Thickness: 5.0mm
Minimum Thickness: 1.0mm
If the thickness reaches the minimum thickness or below, or
serious/uneven abrasion occurs, replace a new brake shoe.

Brake System -Rear Brake Drum4-10213. Check the brake shoe and the brake shoe lining whether they
touch normally.
Mark the inner surface of the brake drum with chalk, joint and
abrade the brake shoe and the inner surface.
If the drum and the lining touch poorly, abrade the brake shoe or
replace a new one.
14. Remove the left front or top brake wheel cylinder.
(1) Unfix the brake oil pipe with a special tool, and collect the
brake fluid with a container.
(2) Remove the bolt and brake wheel cylinder.
15. Remove the brake cup.
(1) Remove the two dust shields from the brake cylinder.
(2) Remove the two pistons and springs.
(3) Remove the two brake cylinder caps from every piston.
16. Check the brake cylinder.
Check the cylinder wall and piston whether there is any rust or nick.
17. Remove the rear discharge screw plug of the brake drum.
18. Tighten the rear discharge screw plug of the brake drum
temporarily.
19. Install the brake wheel cylinder cup.
(1) Apply the lithium soap-base glycol lube on the two brake
wheel cylinder cups and the piston.
(2) Install two brake cylinder caps on every piston.
(3) Install the compression spring and the two pistons on the
brake wheel cylinder.
(4) Install two new dust shields on the brake wheel cylinder.
20. Install the left front or top brake cylinder.
(1) Install the brake cylinder with bolt.
Torque: 9.8N.m
(2) Connect the brake oil pipe with a special tool.
Torque: 15N.m
21. Apply the heat-resistant lube.
Apply the heat-resistant lube on the touch surface of the brake
backboard and the brake shoe.

Brake System -Rear Brake Drum4-10322. Install the parking brake shoe extension rod accessory.
Install a new C-washer, and install the parking brake shoe
extension rod.
23. Install the brake shoe.
(1) Connect the parking brake cable to the parking brake
extension rod with a pair of pinchers.
(2) Install the brake shoe, pin, set spring and set spring cap with
a special tool.
24. Install the return spring of the brake shoe.
Install the return spring on the brake shoe.
25. Install the left brake automatic adjustment rod.
Install the automatic adjustment rod and its spring on the front
brake shoe.
26. Install the parking brake shoe post.
(1) Apply the heat-resistant lube on the adjustment bolt.

Brake System -Rear Brake Drum4-104 (2) As shown in the figure, install the parking brake left post.
27. Install the front brake shoe.
(1) Install the return spring on the front brake shoe.
(2) Install the front brake shoe, pin, set spring and set spring cap
with a special tool.
28. Connect the parking brake shoe left post.
Connect the extension spring to the front/rear brake shoe with a
special tool.
Note:
Be careful not to damage to the dust shield of the brake wheel
cylinder.
29. Check the installation of the brake drum.
(1) Check all parts whether they are installed properly.Braking Plate
parking brake left post

Brake System -Rear Brake Drum4-105 (2) Measure the inner diameter of the brake drum and the
diameter of the brake shoe, and check the difference of them
whether it is a proper brake shoe clearance.
Brake Shoe Clearance: 0.3mm
Note:
Don't apply the oil or lube on the friction surface of the brake shoe
lining and brake drum.
30. Adjust the shoe clearance of the brake drum.
(1) Install two wheel hub nuts temporarily.
(2) Turn around eight teeth of the adjustor.
(3) Install the hole plug.
31. Install the rear brake drum sub-assembly.
32. Add the brake fluid to the storage tank.
33. Discharge the air in the master cylinder.
34. Discharge the air in the brake pipeline.
35. Check the level height in the storage tank.
36. Check the brake fluid whether there is any leakage.
37. Install the rear wheel.
Torque: 103N.m
38. Check the stroke of the parking brake extension rod.
39. Adjust he stroke of the parking brake extension rod.Extend

Brake System -Parking Brake System4-106Section 8 Parking Brake SystemComponent View#3 parking brake extension rod
Lithium soap base glycol lubespecified torqueN.
m :Parking brake balance port Parking brake extension rod
Inhaul cable #1 adjustment nutParking brake balance port Parking brake extension rod accessory
Parking brake switch component

Brake System -Parking Brake System4-107Adjustment1. Remove the rear wheel.
2. Adjust the clearance of the brake shoe.
3. Install the rear wheel.
Torque: 103N.m
4. Check the stroke of the parking brake extension rod.
Pull the parking brake extension rod, and count the number of sound.
Parking Brake Extension Rod Stroke: Pull with 196N force till 6-9 clicks.
5. Adjust the stroke of the parking brake extension rod.
(1) Remove the glove box cover.
(2) Turn #1 adjustment nut inhaul cable till the stroke is ok.
(3) Install the glove box cover.Parking Brake System The table below can help you find out the possible failure reasons. The number means the possible sequence
of the reasons. Check the parts, and replace the corresponding parts if necessary.Parking Brake Tension Rod Component1. Remove the accessories of the console.
2. Remove the middle console.
3. Remove #1 adjustment nut wire.
Remove #1 adjustment nut wire.
4. Remove the accessories of the parking brake extension rod.
(1) Remove the connector of the parking brake extension rod
switch.
(2) Remove the two bolts, and remove the parking brake exten
sion rod.
5. Remove the parking brake switch component.
Remove the screw and parking brake switch component.Suspected location
1. The stroke of the parking brake extension rod is misadjusted.
2. The parking brake inhaul cable is trapped.
3. The clearance of the parking brake shoe is misadjusted.
4. The parking brake lining is cracked or deformed.
5. The return or extension spring is damaged.Symptom
Brake is blocked.#1 adjustment nut inhaul cable

Brake System -Parking Brake System4-108Brake shoe baseboard
Parking brake shoe
Left positioning postRear Brake shoe
Shoe pad set spring cap
Rear brake shoe
Shoe pad set spring cap Shoe pad set springParking System Component
Replacement For left parking brake inhaul cable component, carry out the same steps as the right side.
1. Remove the accessories of the console. 6. Install the parking brake switch component.
Install the parking brake switch component with screw.
7. Install the accessories of the parking brake extension rod.
(1) Install the extension rod on the parking brake inhaul cable, and install #1 adjustment nut wire.
(2) Fasten the parking brake extension rod with two bolts.
Torque: 13N.m
(3) Connect the connector of the parking brake switch.
8. Install the accessories of the console.
9. Install the middle console.
10. Check the stroke of the parking brake extension rod.
11. Adjust the stroke of the parking brake extension rod.Shoe pad set spring
Brake drum Return spring Rear brake automatic adjustment
rod springLeft rear brake automatic
Adjustment rod