2008 GEELY FC battery

2. Inspect the function of generator
(a) low speed:
Connect battery positive wire with joint terminal SWL, connect negative to terminal ES. Inspect whether
generator work at low speed.
If its function does not in conformity with regulations, replace wiper.
(b) high speed
Connect battery positive wire with joint terminal SWH, connect negative to terminal WS. Inspect
whether generator work at high speed.
If its function does not in conformity with regulations, replace wiper.
(c) Free stop position
(1) Connect battery positive wire with joint terminal SWL, connect negative to terminals ES to make
generator work at low speed. Disassemble terminal SWL
lead to make generator stop except stop position.
(2) Connect terminal SWL with terminal AS
(3) Connect battery positive wire with joint terminal SWL to
make generator work at low speed again. Inspect gen-
erator whether stop at the stop position.
If its function does not in conformity with regulations,
replace wiper.
Wiper and cleaner--Wiper and cleaner system
Free stop
position
 301 

Audio system
Audio system
Notes
1. Observe notes for disposal and operation
(a) Please explain to customers: when take battery’s negative terminal off, the memory broadcasting
station on the audio AM/FM set on the radio will be deleted. So, before taking battery
s negative
terminal off ,note the station’s information according to your need. After taking back negative terminal,
set former station again.
(b) Before disassemble/assemble the radio, inspect and take cassette and CD out in.
Clues on: the malfunction of disassemble/assemble the radio is because the tape or CD can
not take out. Do not take it out by force. Drive the car to the service station.
(c) Do not touch the audio film of loudhailer
2. Refer to instructions about using and maintaining audio system
Audio system--Audio system
 307 

Audio system--Outdoor antenna
Outdoor antenna
Change
1. Disassemble battery negative wire
2. Put the front tyre forward
3. Disassemble safety airbag assembly at the side of the driver
4. Disassemble steering wheel
5. Disassemble integration instrument cap
6. Disassemble integration instrument
7. Disassemble panel NO.3 air outlet
8. Disassemble panel NO.1 air outlet
9. Disassemble panel center air outlet trim board
10. Disassemble glove box
11. Disassemble right front pillar trim board
12. Disassemble left front pillar trim board.
13. Disassemble the joint of the safety airbag at the side of the passenger
14. Disassemble panel
15. Disassemble right front door trim board.
16. Disassemble right side trim board.
17. Disassemble antenna assembly [67000136]
(a) Take removable antenna pillar plug apart from radio.
18. Assemble antenna assembly [67000136]
19. Assemble panel
20. Assemble helix cable.
21. Assemble steering wheel
22. Inspect steering wheel whether it dead against the center.
23. Inspect horn button.
24 Assemble horn button
25. Inspect SRS warning light
 312 

Horn--system
Horn system
Horn system
Position
Inspect
1. Inspect the relay
(a) Inspect Whether horn relay (mark: HORN)is conduct
If the conduction situation does not accord with regulations, re-
place the relay.
Horn (alt)
Horn (undertone)
 316 
Condition regular situations
Normal 1-2conduction
Supply battery voltage 3-5conduction
to Terminal 1 and 2avometer connection terminal

Windshield/bodywork glass/wing mirror--Electric window control system
Switch position avometer terminalssituations
UP 4-5, 2-3conduction
OFF 4-5, 1-3conduction
DOWN 2-5, 1-3conduction
Battery terminals working direction
Battery anode lead-terminal 5 main driving axis working
Battery cathode lead-terminal 4 as clockwise
Battery anode lead-terminal 4 main driving axis working
Battery cathode lead-terminal 5 as anticlockwise
2. Inspect electric window switch assembly
Active switch, inspect the conduction among the joint terminals.
If the conduction does not limit to regulations, replace electric
window main switch.
3. Inspect left rear electric window motor assembly.
(a) Inspect the function of left rear electric window assembly.
(1) Inspect whether the motor works calmly.
4. Inspect electric window shift relay [67000061]
Check the conduction of relay (mark: P/W)
If the conduction does not limit to regulations, replace relay.
 320 
Conditionsavometerregular situations
Always 1-2conduction
Supply battery voltage
To that between terminal 13-5 conduction
and terminal 2

Windshield/bodywork glass/wing mirror--Fogbroom system
Inspect
1. Inspect the relay
Inspect the conduction of rear window demist(defrost) relay
(mark: DEF)
If the conduction does not accord with the regulations, replace
relay.
 328 
Conditionsavometer terminals regular situations
Always 1-2conduction
Supply battery voltage
between terminal1 and 3-5 conduction
Terminal2

Windshield/bodywork glass/wing mirror--Electric rearview mirror control system
INSPECT
1. Inspect rear view mirrors switch
Inspect conduction of rearview mirror.
(1) Adjust left or right for side of the switch.
Inspect conduction of rearview mirror on left side
Replace the switch if it does not accord with the regulations.
(2) Adjust right side of left and right switch.
Inspect conduction of rearview mirror on right side
Replace the switch if it does not accord with the regulations.
(3) Inspect conduction of retracting switch
Switch positionsAvometer terminalsRegular situations
ON - Not conduction
Up 3-8, 6-7Conduction
Down3-7, 6-8Conduction
Left 2-8, 6-7Conduction
Right2-7, 6-8Conduction
Switch positionsAvometer terminalsRegular situations
Position of driving 8-9, 7-10Conduction
Position of retracting 8-10, 7-9Conduction
Replace the switch if it does not accord with the regulations,
2. Inspect rear rear view mirror
(a) Inspect motor function of rearview mirror
(b) Inspect function of electric retracted motor
Battery terminals Positions of rearview mirror
Positive wire (+) -A
Turn left
Negative wire (-) -B
Positive wire (+) -B
Turn right
Negative wire (-) -A
Positive wire (+) -C
Turn up
Negative wire (-) -B
Positive wire (+) -B
Turn down
Negative wire (-) -C
Left and right
adjusting switchFolding switch
(optional)
Rearview
mirror
switch
 332 
Switch positionsAvometer terminalsRegular situations
ON - Not conduction
Up 5-8, 6-7Conduction
Down5-7, 6-8Conduction
Left 4-8, 6-7Conduction
Right4-7, 6-8Conduction

Windshield/bodywork glass/wing mirror--Electric rearview mirror control system
Replace the rearview mirror if actuation does not accord with regulations. Notes:
zWhen repeat the same inspection, cut off the voltage of battery, then inspect again with
same steps.
zWhen supply battery voltage, the rearview mirror will not retract even if trying to move the
crust of rearview mirror.
Outer rearview mirror assembly L
Outer rearview mirror assembly R
L terminal
connecting wireL terminal
connecting
wire
assembly L assembly R
 333 
Positions of rearview mirror
A (position of driving)
B (between position of driving
and retracting)
C (position of retract)Connection style
Connect wire G to positive
Connect wire D to negative
Connect wire D to positive, connect wire G to negative
Connect wire G to positive, connect wire D to negative
Connect wire D to positive
Connect wire G to negativeActuated style
Not actuated
A-B-C
C-B-A
Not actuated
Positions of rearview mirror
A (position of driving)
B (between position of driving
and retracting)
C (position of retract)Connection style
Connect wire D to positive
Connect wire G to negative
Connect wire G to positive, connect wire D to negative
Connect wire D to positive, connect wire G to negative
Connect wire G to positive
Connect wire D to negativeActuated style
Not actuated
A-B-C
C-B-A
Not actuated