2008 GEELY FC mirror

Windshield/bodywork glass/wing mirror--Electric rearview mirror control system
(c) When operating left and right rearview mirrors, inspect whether ignition switch works when turn it to
OFF.
(1) When operating left and right rearview mirrors, turn ignition switch to OFF and inspect rearview
mirrors function whether they stop.
(2) Turn ignition switch to ACC again, inspect whether rearview mirrors work
Clues on: Turn ignition switch to OFF, if you press retractable switch and turn ignition
switch to ACC, then left and right rearview mirrors will move to opposite position.
(d) Inspect whether rearview mirrors work when restricted by others.
(1) When left and right rearview mirrors move to retractable position or steering position, restrict left
and right rearview mirrors manually, inspect retraction stops.
(2) Press retractable switch again, inspect whether it works.(at the opposite direction of stop position)
 330 

Windshield/bodywork glass/wing mirror--Electric rearview mirror control system
Positions
Trouble table
Trouble
rearview mirrors do not work
rearview mirrors work abnormallyComponents name
1. (accessory) fuse
2. rearview mirror switch
3. wiring harness
1. rearview mirror switch
2. wiring harnessReference page
-
332
-
332
-
 331 
Left rear view mirrorsElectric rear view mirrors
switch
Right rearview mirrors

Windshield/bodywork glass/wing mirror--Electric rearview mirror control system
INSPECT
1. Inspect rear view mirrors switch
Inspect conduction of rearview mirror.
(1) Adjust left or right for side of the switch.
Inspect conduction of rearview mirror on left side
Replace the switch if it does not accord with the regulations.
(2) Adjust right side of left and right switch.
Inspect conduction of rearview mirror on right side
Replace the switch if it does not accord with the regulations.
(3) Inspect conduction of retracting switch
Switch positionsAvometer terminalsRegular situations
ON - Not conduction
Up 3-8, 6-7Conduction
Down3-7, 6-8Conduction
Left 2-8, 6-7Conduction
Right2-7, 6-8Conduction
Switch positionsAvometer terminalsRegular situations
Position of driving 8-9, 7-10Conduction
Position of retracting 8-10, 7-9Conduction
Replace the switch if it does not accord with the regulations,
2. Inspect rear rear view mirror
(a) Inspect motor function of rearview mirror
(b) Inspect function of electric retracted motor
Battery terminals Positions of rearview mirror
Positive wire (+) -A
Turn left
Negative wire (-) -B
Positive wire (+) -B
Turn right
Negative wire (-) -A
Positive wire (+) -C
Turn up
Negative wire (-) -B
Positive wire (+) -B
Turn down
Negative wire (-) -C
Left and right
adjusting switchFolding switch
(optional)
Rearview
mirror
switch
 332 
Switch positionsAvometer terminalsRegular situations
ON - Not conduction
Up 5-8, 6-7Conduction
Down5-7, 6-8Conduction
Left 4-8, 6-7Conduction
Right4-7, 6-8Conduction

Windshield/bodywork glass/wing mirror--Electric rearview mirror control system
Replace the rearview mirror if actuation does not accord with regulations. Notes:
zWhen repeat the same inspection, cut off the voltage of battery, then inspect again with
same steps.
zWhen supply battery voltage, the rearview mirror will not retract even if trying to move the
crust of rearview mirror.
Outer rearview mirror assembly L
Outer rearview mirror assembly R
L terminal
connecting wireL terminal
connecting
wire
assembly L assembly R
 333 
Positions of rearview mirror
A (position of driving)
B (between position of driving
and retracting)
C (position of retract)Connection style
Connect wire G to positive
Connect wire D to negative
Connect wire D to positive, connect wire G to negative
Connect wire G to positive, connect wire D to negative
Connect wire D to positive
Connect wire G to negativeActuated style
Not actuated
A-B-C
C-B-A
Not actuated
Positions of rearview mirror
A (position of driving)
B (between position of driving
and retracting)
C (position of retract)Connection style
Connect wire D to positive
Connect wire G to negative
Connect wire G to positive, connect wire D to negative
Connect wire D to positive, connect wire G to negative
Connect wire G to positive
Connect wire D to negativeActuated style
Not actuated
A-B-C
C-B-A
Not actuated

Engine cover/automobile door--Front automobile door 368 Name of parts Specification Amount Marked
number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33Number of parts
68000147
68000162
68000149
Q1860610
68000159
67000157
Q32006
68000153
Q2580816
Q1860610
JQ2756316
67000123
Q1860610
68000145
Q2716319
67000132
68000144
Q2714216
68010050
Q2204816
67000107
68000141
68000160
62000479
62000025
62000024
Q1840820
68000163JQ1840816T1F31Q1400616
62000027
68010052
68000151Right front glass assembly
Seal tape of right front glass leading slot
Right front glass leading slot assembly
Hexagon flange face bolt
Exterior seal tape of right front door glass
Right exterior electric rearview mirror assembly
Hexagon flange face nut
Right front door locker organization assembly
Inner hexagon floriated raised countersunk head screw
Hexagon flange face bolt
Combination part of hexagon head self-tapping screw with flat gasket
Right front door glass lift assembly
Hexagon flange face bolt
Right front door board bracket
Cross slot plate head self-tapping screw
Right front small speaker cover assembly
Right front door control panel assembly
Freerson plate head self-tapping screw
Right front door inner defending board assemblyCombination part of cross slot plate head self-tapping screw with flat washerDoor light assembly
Right front door defender water curtain assembly
Right front door seal tape assembly
Right front door assembling assembly
Right front door upper hinge assembly
Hexagon flange face bolt (with step)
Hexagon flange face bolt
Front door limiter assembly
Hexagon flange face bolt
Combination part of hexagon head bolt with flat washer
Right front door lower hinge assembly
Right side door inner handle assembly
Right front door exterior handle assembly1
1
1
1
1
1
3
1
3
2
1
1
6
1
2
1
1
1
1
1
1
1
1
1
1
2
4
2
2
2
1
2
1M6 × 10
M6
M6× 18
M6× 10
ST6.3 × 16
M6 × 10
ST6.3 × 19
ST4.2 × 16
ST4.8 × 16
M8× 20
M8× 20
M8× 16
M8× 16

Engine cover/automobile door--Front automobile door
Overhaul
Hint:
zWhen assembling, please work by the sequence which is opposite with disassembling
sequence; but when it has items that need to pay special attention, it will add special
specification.
zOverhaul procedure for right side is same as the left side.
zPlease refer to subassembly figure of front door on page 360.
1. Disassemble left front door control panel assembly [68000142]
(a) Disassemble the screw.
(b) Use screw driver to disassemble left front door control panel assembly.
Hint: before using screw driver, it is necessary to wrap its needled top with adhesive tape.
(c) Disassemble the joint.
2. Disassemble left front door inner defending board assembly [68010049]
(a) Disassemble the screw.
(b) Without equipping with door control light: use screw driver to disassemble door inner defending board
assembly.
(c) Equipping with door control light: use screw driver to disassemble door inner defending board assembly,
then disassemble the joint again.
(d) Equipping with door control light: use screw driver to disassemble door control light.
3. Disassemble left door inner handle assembly [68010051]
(a) Disassemble inner handle, and disassemble two pull cables from inner handle.
4. Disassemble repairing hole cover of left front door
5. Disassemble left front small loudhail cover assembly [67000131]
 369  6. Disassemble left exterior electric rearview mirror
assembly [67000155]
(a) Disassemble the joint.
(b) Disassemble three screw caps and left exterior electric
rearview mirror.
7. Disassemble exterior seal tape of left front door glass
[68000158]

Exterior/inner trim board--Inner trim board of top
left pillar [68010018]
13. Disassemble upper inner trim board assembly of
right pillar [68010025]
(a) Disassemble the bolt and upper fixing bolt trim cover of front
safety belt.
(b) Use screw driver to disassemble upper inner trim board of
right stand pole.
Hint: before using screw driver, its needled top should
be twisted by adhesive tape.
(C) Use same method to disassemble the trim board at the
other side.
14. Disassemble upper inner trim board assembly of
left pillar [68010023]
15. Disassemble rear row chair cushion (referring to
page 352).
16. Disassemble rear row chair backrest (fixing type)
(referring to page 354).
17. Disassemble rear row chair right backrest assem-
bly (referring to page 352).
18. Disassemble rear row chair left backrest assembly
(referring to page 352).
19. Disassemble inner trim board of right rear pillar
assembly [68010027]
(a) Use screw driver to disassemble inner trim board of right
rear pillar assembly.
Hint: before using screw driver, its needled top should
be twisted by adhesive tape.
(b) Use same method to disassemble the trim board at the
other side.
20. Disassemble inner trim board of left rear pillar as-
sembly [68010026]
21. Disassemble inner trim board of right front pillar
assembly [68010017]
(a) Use screw driver to disassemble inner trim board of right
front pillar assembly.
Hint: before using screw driver, its needled top should
be twisted by adhesive tape.
(b) Use same method to disassemble the trim board at the
other side.
22. Disassemble inner trim board of left front pillar as-
sembly [68010014]
23. Disassemble inner rear view mirror assembly [67010013]
(a) Use screw driver to disassemble trim cover of inner rearview
mirror pedestal.
Hint: before using screw driver, its needled top should
be twisted by adhesive tape.
(b) Disassemble two screws and inner rearview mirror assembly.
Fixing
clamp
Fixing
clamp
Fixing
clamp
 391 

Electric rearview mirrorElectrical schematic diagram--Electric rearview mirror 401