198Chapter 5 Light SystemSection 1 Survey of Light SystemI. COMPOSITION1. Front combination lamp assembly: turn signal lamp, high beam, low beam, head lamp, front position lamp.
2. Rear combination lamp: turn signal lamp, back-up lamp, rear fog lamp, tail lamp, brake lamp, retro reflector.
3. Front fog lamp
4. Side turn signal lamp
5. High mounted stop lamp
6. Rear trunk lamp
7. License plate lamp
8. Interior dome lamp
9. Rear row reading lamp
10. Door lampshield and bulb assemblyII. NOTES FOR REPAIR1. NOTES WHEN REPAIRING ELECTRICAL EQUIPMENTS
(a) Disconnect the battery ground cable.
2. Notes when replacing a headlamp bulb
(a) Before replacing a halogen bulb, turn the headlamp OFF to make it cool.
(b) When installing a new halogen bulb, do not touch the glass part of the bulb with bare hands.
(c) If there is oil stain on the surface of halogen bulb (headlamp and front fog lamp) when the lamps are
turned ON, its service life will be shortened.
(d) Halogen bulbs (headlamp and front fog lamp) have pressurized gas inside and require special handling.
They can explode if dropped to ground.The glass fragments will splash up.
(e) When replacing, make sure to use the bulbs with the same power, same model.
(f) After the bulb is installed, make the lamp holder tight.
2044. TURN SIGNAL AND HAZARD WARNING SYSTEM
5. BRAKE LAMP SYSTEMSymptom Suspec te d Area
1. HAZARD Fuse
2. Ce ntra l c ontrolle r
3. H a rne ss
1. Hazard warning switch
2. H a rne ss
1. Turn s igna l sw itc h
2. H a rne ss
1. Turn s igna l sw itc h
2. H a rne ss
1. Bulb
2. H a rne ss Only one bulb dose not light up “Haza rd" a nd “Turn” doe s not ope ra te
Ha za rd wa rning la mp doe s not ope ra te (Turn is
norma l)
Ha za rd wa rning la mp is abnormal (Ha za rd is
a bnorma l)
Turn signa l dose not light up in one direc tionSymptom Suspec te d Area
1. Bra ke la mp fus e
2. Brake lamp switch
3. H a rne ss
1. Brake lamp switch
2. H a rne ss
1. Bulb
2. H a rne ss
1. Bulb
2. H a rne ss Brake la mps on both side s do not light up
Br a ke la mp re ma ins a lw a ys O N
Bra ke la mp dose not light (One side )
High mounte d Bra ke la mp dose not light up
(Stop la mp is norma l)
212II.INSTALLATION1. Install the electrical connector of the headlamp assembly.
2. Install the headlamp assembly and the 3 mounting bolts.
3. Install the front bumper.
4. Adjust the condition of the vehicle.
5. Adjust the headlamp beam.III.HEADLAMP BULB REPLACEMENT1 - LOW BEAM DUST COVER 2 - HIGH BEAM DUST COVER 3 - TURN SIGNAL LAMP DUST
COVER 4 - HEADLAMP HOLDER
1. Replace the high and low beam bulbs
y Turn and remove the dust cover counter-clockwise
y Pull out the bulb plug
y Press and release the wire clip
y Pull out the lamp-holder, and remove the bulb
y Replace the bulb
2. Replace the turn signal lamp bulbs
y Remove the 3 screws on the dust cover with screwdriver
yTurn the lamp-holder counter-clockwise. Pull out the lamp-holder, and remove the bulb
yReplace the bulb
3. Replace the headlamp bulbs
yTurn the lamp-holder counter-clockwise. Pull out the lamp-holder, remove the bulb, and replace the
bulb.1 2 3 4
