2008 GEELY CK engine oil

Table of ContentsPart I Engine ...........................................................................1Chapter 1 Engine Assembly (MR479Q, MR479QA, MR481QA)...................1Section 1 Routine Inspection.........................................................................................1
Section 2 Drive Belt Replacement ...............................................................................5
Section 3 Valve Clearance Adjustment...........................................................................6Chapter 2 Engine Components Replacement
(MR479Q, MR479QA, MR481QA)................................................................10Section 1 Engine Components....................................................................................10
Section 2 Engine Components Replacement............................................................13
Section 3 Timing Belt Replacement.........................................................................17
Section 4 Camshaft Replacement............................................................................22
Section 5 Cylinder Head Gasket Replacement.........................................................28
Section 6 Oil Pump Oil Seal Replacement................................................................33
Section 7 Engine Rear Oil Seal Replacement............................................................34Chapter 3 Lubrication System (MR479Q, MR479QA, MR481QA)...............35Section 1 Oil Pressure Gage Sensor Replacement....................................................35
Section 2 Oil Pump Assembly Replacement..............................................................36
Section 3 Oil Filter Replacement................................................................................38
Section 4 Starter Replacement.................................................................................39
Section 5 Generator Replacement............................................................................40Chapter 4 Fuel System (MR7131A, MR7151A, MR7161A)........................41Section 1 Check Fuel System Pressure.....................................................................41
Section 2 Fuel Pump Inspection...................................................................................42
Section 3 Fuel Injector Replacement.........................................................................43
Section 4 Fuel Pump Replacement............................................................................45
Section 5 Fuel Emission Control System....................................................................47
Section 6 Carbon Canister Replacement....................................................................48Chapter 5 Exhaust System (MR7131A, MR7151A, MR7161A).................50

Chapter 6 Cooling System Inspection
(MR7131A, MR7151A, MR7161A).................................................................52Section 1 System Check
Section 2 Water Pump, Thermostat and Radiator Replacement.................................... 54Chapter 7 Clutch (MR7131A, MR7151A, MR7161A)....................................56Section 1 Clutch Replacement...................................................................................57Chapter 8 Maunal Transaxle Assembly
(MR7131A, MR7151A, MR7161A)................................................................59Section 1 Manual Transaxle Replacement..................................................................60
Section 2 Vehicle Speed Sensor Replacement
Section 3 Transmission Case Oil Seal..........................................................................62
Section 4 Transaxle Case Oil Seal Replacement........................................................63Chapter 9 General Engine Troubles and Their Troubleshooting....................64Section 1 Overview........................................................................................................64
Section 2 General Engine Fault and Troubleshooting.......................................................64
Section 3 Engine Noise Diagnosis and Troubleshooting................................................77Chapter 10 Engine Management Unit..............................................................81Section 1 System Description.........................................................................................81
Section 2 System Component and Working Principle......................................................82Part II Chassis............................................................................85Chapter 1 Transmission Control Device.........................................................85Section 1 Transmission Control Device.........................................................................85
Section 2 Lever Type Transmission Control Device......................................................85
Section 3 Cable Type Transmission Control Module......................................................87Chapter 2 Accelerator Pedal............................................................................90Section 1 Accelerator Pedal..........................................................................................90Chapter 3 Clutch Control System....................................................................91Section 1 Clutch Control System....................................................................................91
Section 2 Clutch Cable Control Mechanism.....................................................................91
Section 3 Clutch hydraulic Control Device.......................................................................94Chapter 4 Propeller Shaft...............................................................................97...............................................................................................52
..............................................................61

1Part I EngineChapter 1 Engine Assembly
(MR479Q, MR479QA, MR481QA)Section 1 Routine Inspection1. Check coolant
2. Check engine oil
3. Check battery
4. Check air cleaner element assembly
5. Check spark plug
6. Check drive belt
Figure 1
Notice:
zCheck the belt deflection at the specified point See (Figure 1).
zSet tension to specified value when installing new belt.
zCheck the deflection to ensure it is below the specified value after the belt runs for over 5 minutes.
zReinstall the belt which has been running for over 5 minutes. The deflection of the old belt is regarded as
the standard for inspection.
zCheck V-belt for tension and distortion after the engine cranks for 2
turns.
7. Check ignition timing See (Figure 2)
a) Warm up the engine.
b) When using fault diagnosis tester
Connect fault diagnosis tester to fault diagnosis interface socket.
Ignition timing:
MR479Q: 10 ± 2° BTDC (before top dead center) at idle
MR479QA: 10 ± 2° BTDC at idle
MR481QA: 10 ± 2° BTDC at idleFigure 2New Belt mm Old Belt mm
Fan Belt 7～
13. 5
Power steering Belt 5～
66～
8
A/C Belt 6. 5
～78～
9 Belt deflection See (Table 1)
Be lt pre ssure : 98NBelt Looseness
Measuring PointWater pump
Power steering
crankshaftgenerator
Air condition
compressor pump11.5～
9

3The Min. compression pressure: 980 kPa
The tolerance range of the cylinders pressure: 100 kPa
Notice:
zEnsure sufficient battery power and the engine speed is no less than 250 RPM (revolutions per minute).zCheck the compression pressure of other cylinders in the same way.
zComplete the measure as quick as possible.
(4) If the compression pressure in several cylinder is too low, fill some engine oil to the cylinder via the
hole of the spark plug. Check by repeating step 1-3.
Hint:
zIf the compression pressure is improved after filling oil, the piston ring or the cylinder may be abrased
or damaged.
zIf the pressure is still too low, the valve is stagnation or poor seal, or there is a leakage in gasket.
10. Check CO/HC
(a) Start engine.
(b) Running engine at 2500rpm for approximately 3 minutes.
(c) Insert CO/HC meter testing probe into tailpipe at least 40cm during idling.
(d) Check CO/HC concentration at idle and 2500rpm.
Hint:
zComplete measurement within 3 minutes.
zTest the CO/HC emission concentration at idle and 2500 rpm on QC/T630-1999 standard.
(e) Take the following steps to diagnose the fault if the CO/HC concentration does not comply with standard .
(1) Check the oxygen sensor operation.
(2) See (Table 3) for the possible cause and check and repair.

8Notice:Due to the small end play on camshaft, the cylinder head may be damaged by the thrust force when removingit, it may stuck or damage camshaft. Take the following steps to avoid damage: (1) Turn the crankshaft pulley to make exhaust camshaft dowel pin is a bit higher than the cylinder head. See(Figure 15). (2) Align the matchmark on each gear to engage intake camshaft gear and exhaust camshaft gear. See(Figure 16).
(3) When the gears are engaged, install the intake camshaft bearing onto bearing journal.
Hint:
The intake camshaft lobe of cylinder 1 and 3 can jack up their own valve tappet.
(5) Install 4 bearing caps to the right position.
(6) Apply a light layer of engine oil on the thread and under the head of bearing cap bolts.
(7) Uniformly install and tighten 8 bearing cap bolts in several times, in the sequence shown in the figure.
Torque: 13N. m
(8) Remove service screw.
(9) Install the bearing cap No. 1. in the direction of the forward arrow mark.
(10)Apply a light layer of engine oil on the thread and under the head of bearing cap bolts.
(11)Alternatively tighten and install 2 bearing bolts.
Torque: 13N. m
7. Adjust exhaust valve clearance. See (Figure 17)
Remove adjust gasket.
(1) Crank to keep the camshaft head upward.
(2) Face valve tappet nick to vehicle front. (3) Press valve tappet, put special tool between camshaft and valve tappet.Hint:
zLean the end with mark "9" into the position in (Figure 18).Figure 15Install MarkTiming MarkMarch MarkCam LobeUpward
NickFrontFigure 17
Figure 18 Figure 16

9(4) Alternatively press valve tappet with the special tool (A) (B). Check
valve clearance. See (Figure 19).
8. Install cylinder head sub-assembly
(a) Remove all old gasket material.
(b) Apply the seal glue to the cylinder head.
(c) Connect wire harness and clip.
(d) Install gasket under of cylinder head.
(e) Install the cylinder head cover with 4 seal gaskets and 4 screw caps.
Torque: 7.8N. m
(f) Install 2 ventilation hoses to cylinder head cover.
(g) Connect generator wire joint.
(h) Connect generator wires.
(i) Connect oil pressure switch connector.
(j) Install wire clip.
(k) Connect A/C compressor switch connector.
9. Install electronic ignition coil and high voltage cable
10. Check engine oil for leakage
Figure 19

10Chapter 2 Engine Components Replacement
(MR479Q, MR479QA, MR481QA)Section 1 Engine ComponentsComponent 1Air Filter Assembly W/ Hose
Accelerator Control
Cable Assembly
Heater Inlet Hose
Heater Outlet Hose
Fuel Sub-Assembly
Efi Fuel Pipe Clamp
MT:
Transmission
Control Cable
Assembly
AT :
Transmission Control Cable Assembly MT:
Clutch Release
Cylinder Assembly
Radiator Outlet Pipe Radiator Inlet Pipe
Starter AssemblyAT: Oil Cooler Outlet Pipe
AT: Oil Cooler Inlet Pipe
Radiator Assembly
BatteryFront Exhaust
Pipe Assy.3-way catalytic
converterMufflerTail PipeFigure 20

1421. Remove radiator assembly
22. Remove engine V-belt
23. Remove No. 1 V- belt (A/C compressor to crankshaft pulley)
24. Remove generator assembly
25. Remove A/C compressor
26. Remove compressor installing No. 1 bracket. Remove 4 bolts and compressor installing No.
1 bracket.
27. Remove starter assembly
28. Remove power steering pump V- belt
29. Detach power steering pump assembly
30. Remove power steering pump, adjust the bracket
31. Detach manual transaxle assembly (Separate automatic transaxle assembly)
32. Detach clutch cover panel assembly.
33. Detach clutch pressure plate assembly.
34. Detach flywheel sub-assembly.
35. Remove engine rear end cover.
36. Remove injector assembly and remove intake manifold.
Remove 2 bolts and intake manifold support and remove 7 bolts,
2 nuts, intake manifold and gasket. See (Figure 27).
37. Remove knock sensor
38. Remove water temperature gauge sensor
39. Remove crankshaft position sensor
40. Remove engine oil pressure switch
41. Remove water inlet hose housing
42. Remove water outlet hose joint
43. Detach exhaust manifold. See (Figure 28)
44. Remove engion oil filter sub-assembly
45. Remove ignition coil and high voltage cable
46. Install engine sub-assembly
47. Install ignition coil and high voltage cable
48. Install engine oil filter sub-assembly
49. Install exhaust manifold
(a) Install new gasket and exhaust manifold stay with
5 nuts, Torque: 34N. m
(b) Install exhaust manifold stay with two bolts.
Torque: 59N. m
(c) Install upper heat shield with 4 bolts.Torque: 17N. mFigure 27
Figure 28